DLA A-A-59487 B-2010 PADLOCK (KEY OPERATED).pdf

1、ASMC N/A FSC 5340 INCH-POUND A-A-59487B 3 May 2010 SUPERSEDING A-A-59487A 3 July 2001 COMMERCIAL ITEM DESCRIPTION PADLOCK (KEY OPERATED) The General Services Administration has authorized the use of this Commercial Item Description for all federal agencies. 1. SCOPE: This Commercial Item Description

2、 (CID) covers key operated, dead bolt padlocks intended for low security use. 2. SALIENT CHARACTERISTICS: 2.1 Padlock furnished under this CID shall be individually keyed, double dead -bolt locking construction and shall conform with the requirements of ASTM F883, Type P01, Option A (captive key). P

3、adlocks shall conform to the dimensions as specified in Table I and figures below. FIGURE 1. PADLOCK. Comments, suggestions, or questions on this document should be addressed to Defense Supply Center Philadelphia, ATTN: DSCP-NASA, 700 Robbins Avenue, Philadelphia, PA 19111-5096 or email to dscpg&isp

4、ecommentsdla.mil. Since contact information can change, you may want to verify the currency of this address information using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59487B 2Table

5、I. DASH NUMBER and DIMENSIONS DASH NUMBER A .100 B REF C .040 D E F MIN MAX MIN MAX MIN MAX 1 1.500 2.790 .281 .688 1.188 1.250 2.000 .594 .770 1.500LONG SHACKLE 4.660 2.500 3.0002 1.750 3.375 .343 1.125 1.500 1.250 2.000 .688 .820 2.2 Material. Shackle, case, spring and attachments shall be in acco

6、rdance with the following: a. Brass or bronze conforming to ASTM B16/B16M, B30, B505/B505M, B584, or B770. b. Corrosion resistant steel, carbon steel or alloy steel as required in commercial practice unless otherwise specified. c. Spring shall be phosphor bronze conforming to ASTM B159/B159M. d. Ste

7、el shackle Shall be uniformly case hardened and shall meet the minimum desired grade requirements as specified for Forcing Tests of ASTM F883. e. Attachment clevis Shall be brass or steel with zinc electroplated coating of ASTM B633. 2.3 Finish. Brass or bronze clear lacquer on exterior in accordanc

8、e with commercial practice. Carbon steel or alloy steel shall be zinc or chromium electroplated conforming to ASTM B633 or B177. Prior to application of any coating, all exterior surface shall have a smooth finish. Sharp edges and burrs shall be removed. The case surface shall have a smooth or tumbl

9、ed finish for laminated construction. 2.4 Lubrication. Working parts shall be lubricated as needed with a lubricant normally used for the intended purpose. 2.5 Case. Unless The case shall be either laminated or solid as specified (see 6.4) of the materials indicated for the type of padlock. If a sol

10、id steel case is specified, the case shall be uniformly case hardened steel with a hardness in the range of 40 to 50 on the Rockwell C scale (40-50 HRC). 2.6 Shackle. The shackle shall be “U” shaped and may be either spring released or pull released. The diameter of the shackle shall be as specified

11、 in Table I. When steel shackle is specified, the shackle shall be uniformly case hardened. 2.7 Keying. All keys shall be captive (unremovable) in the cylinder when unlocked. Each padlock shall be furnished with two (2) keys. No key shall operate more than one (1) padlock per 50 padlocks. Individual

12、ly keyed padlocks shall have at least as many possible key changes as follow: DASH NUMBER 1 4,000 DASH NUMBER 2 10,000 2.8 Chain. When specified, the chain supplied with the padlock shall conform to RR-C-271, Type II, Class 2 or 6 (brass or steel as applicable). The chain shall be nine (9) inches lo

13、ng one (1) link. 2.9 Marking. The markings “U.S.” shall be .25 inch minimum size and can be located on either side of the padlock. 2.10 Padlocks, as a minimum, shall be able to withstand the testing requirements for Grade 2 of ASTM F883 with the following exception: a. Substitute the tensile force v

14、alue per ASTM F883 with 800 pound-force (lbf) for dash number 1 padlocks and 2,000 lbf for dash number 2. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59487B 33. REGULATORY REQUIREMENTS. 3.1 The offerer/contractor is encouraged to use recovere

15、d materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 4. PRODUCT CONFORMANCE PROVISIONS. 4.1 Product conformance. The products provided shall meet the salient characteristics of this commercial item description, conform to the

16、 producers own drawings, specifications, standards, and the quality assurance practices, and be the same product offered for sale in the commercial market. The government reserves the right to require proof of such conformance. 5. PACKAGING. 5.1 Preservation, packing and marking shall be as specifie

17、d in the contract or order. 6. NOTES. 6.1 Unless otherwise specified, all dimensions are in inches. 6.2 Unless otherwise specified in the contract or purchase order, packaging shall be in accordance with ASTM D3951. 6.3 In the event that the requirements of this document should conflict with ASTM F8

18、83, this document should take precedence. 6.4 The following part or identification numbering procedure is for government purposes and does not constitute a requirement for the contractors. The Part Identification Number (PIN) shall consist of the basic commercial item description number followed by

19、a dash number from Table I, plus other options as specified in the example below: AA59487 1 B C L S Add “S” for solid case, omit for laminated case Add “L” for long shackle, omit for standard shackle Add “C” for chain attachment B = brass, S = steel steel (Designations “B” and “S” refer to the mater

20、ial to be used for both the lock body and the shackle.) DASH NUMBER from Table IBasic CID number 6.5 Cross-reference data. Padlocks conforming to this CID, either laminated case or solid case, are interchangeable/substitutable with padlock sets conforming to MS35647E dated 27 Jul 1992. Provided by I

21、HSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59487B 4Table II. CROSS REFERENCE TABLE FOR ACTIVE MS PIN Cancelled MS PIN Replacement CID PIN (Laminated Case) Replacement CID PIN (Solid Case) MS35647-3 AA59487-1BC AA59487-1BCS MS35647-4 AA59487-1B AA59487-1B

22、S MS35647-5 AA59487-1BCL AA59487-1BCLS MS35647-6 AA59487-1BL AA59487-1BLS MS35647-9 AA59487-2SC AA59487-2SCS MS35647-10 AA59487-2S AA59487-2SS 6.6 Source of documents. 6.6.1 FAR. The FAR may be obtained from the Regulatory Secretariat, 1800 F Street NW, Washington DC 20405 or online at http:/www.acq

23、net.gov. 6.6.2 ASTM Standards. Copies of ASTM standards may be obtained from the ASTM International, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959 or online at http:/www.astm.org. 6.7 Ordering data. The contract or order should specify the following: a. CID document number, revision, and C

24、ID PIN. b. Product conformance provisions. c. Packaging requirements. 6.8 Key words. Chain Laminated case Shackle Solid case 6.9 Changes from previous issue. The margins of this specification are marked with vertical lines to indicate where changes (additions, modifications, corrections, deletions)

25、from the previous issue were made. This was done as a convenience only, and the government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marg

26、inal notations and relationship to the last previous issue. MILITARY ACTIVITIES: CIVIL AGENCY COORDINATING ACTIVITY: GSA FAS Custodian: Army AR Preparing activty: Navy YD DLA IS Air Force 99 Review activities: (Project 5340-2010-008) Army AV, CR, MI Navy MC NOTE: The activities listed above were int

27、erested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-