DLA A-A-59535 A-2013 PUMP FUEL ELECTRICAL 12 AND 24 VOLT DC.pdf

1、AMSC N/A FSC 2910 INCH-POUND A-A-59535A 9 December 2013 SUPERSEDING A-A-59535 2 February 2000 COMMERCIAL ITEM DESCRIPTION PUMP, FUEL, ELECTRICAL: 12 AND 24 VOLT DC The General Services Administration has authorized the use of this commercial item description for all federal agencies. 1. SCOPE. This

2、commercial item description (CID) covers the general requirements for pump, fuel, electrical: 12 and 24 volt DC. Pump, fuel, electrical: 12 and 24 volt DC covered by this CID are intended for commercial/industrial applications. 2. CLASSIFICATION/PART OR IDENTIFICATION NUMBER (PIN). This CID uses a c

3、lassification system which is included in the PIN as shown in the following example (see 7.1). AA59535 - 001 CID number Type code 2.1 CID codes for types: CID code 001 = type I (12 VDC nominal) CID code 002 = type II (24 VDC nominal) Beneficial comments, recommendations, additions, deletions, clarif

4、ications, etc., and any data that may improve this document should be sent to: DLA Land and Maritime, ATTN: VAI, P.O. Box 3990, Columbus OH 432183990, or email fluidflow.dla.mil. Since contact information can change you may want to verify the currency of the address information using the ASSIST Onli

5、ne database at https:/assist.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59535A 2 3. SALIENT CHARACTERISTICS. 3.1 Interface and physical dimensions. Pump, fuel, electrical: 12 and 24 volt DC supplied to this CID shall be as specifie

6、d herein. 3.1.1 Envelope. The external dimensions of the pump shall conform to the envelope dimensions shown on figure 1. 3.1.2 Fuel filter. The pump shall incorporate a fuel filter to protect the fuel supply system. The filter shall be removable for cleaning without demounting the pump. 3.1.3 Inlet

7、 and outlet connections. The inlet and outlet connections shall be threaded to interface with the mating threaded part. Internal threads shall be 0.1250 - 27 NPT (American National Standard Taper Pipe Threads) and external threads shall be 0.2500 - 18 NPT. If internal threads are used on the pump, a

8、 threaded adapter shall be provided with external threads of 0.2500 - 18 NPT. The adapter shall not protrude from the pump body more than 0.5 inches. 3.1.4 Electrical connector and cable. The electrical connector shall be as shown on figure 1. The electrical connector shall withstand a pull of not l

9、ess than 60 pounds. The mated connector shall not require more than 30 pounds to separate from its mate at a temperature of -55 degrees Fahrenheit (F). The cable shall conform to MIL-DTL-13486 type I, class A, or equal. When necessary, part or all of the cable may conform to MIL-DTL-13486 type II, c

10、lass A, or equal, provided that a separate cable ground is used. Cables shall exit the pump within or before the area marked “CABLE CLEARANCE” shown on figure 1. Both the cable and the cable ground shall be external to the pump body and shall be located within the cable clearance area shown on figur

11、e 1. The cable shall be flexible down to -55 F. The junction between the connector and cable shall be waterproof. The boot attached to the power cable shall be made of rubber ASTM D2000 M5BC 610 A14E034F19 Z1 (Z1 is method B of C12) in accordance with ASTM D2000, or equal. 3.2 Performance. 3.2.1 Fue

12、l compatibility. The pump shall be capable of operating with the following fuels: a. Diesel fuel oil, grades 1-D and 2-D, conforming to ASTM D975. b. Diesel fuel oil conforming to A-A-52557. c. Jet A-1 turbine fuel conforming to ASTM D1655. 3.2.2 Output. The output of each pump type shall equal or e

13、xceed the applicable performance curve shown on figure 2 when operated at temperatures between 65 and 75 F. The pump fuel flow, at any given pressure, shall be not less than 67% of the value shown in figure 2 in ambient temperatures ranging from -55 to +65 F. 3.2.3 Electrical. The pump shall operate

14、 within the voltage range listed in table I. The negative terminal of the pump shall be connected to ground. The load current shall not exceed 1.75 amperes. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59535A 3 TABLE I. DC voltage. Pump type N

15、ominal voltage Minimum voltage Maximum voltage I 12 6 18 II 24 18 30 3.2.4 Electromagnetic interference suppression. Conducted emissions and radiated emissions on power leads shall not exceed the values shown on figures 3 and 4, respectively. 3.2.5 Dry operation. The pump shall be capable of withsta

16、nding dry pumping operation for a period of not less than 4 hours without evidence of damage or impairment of performance. 3.2.6 Dry prime. The pump shall be capable of commencing and maintaining fuel pumping operation from a dry condition with the fuel source not less than 2.5 feet below the bottom

17、 of the pump. 3.2.7 Endurance. The pump shall maintain a delivery versus pressure relationship not less than that specified in 3.2.2 for a period of not less than 3,000 hours. 3.3 Materials. Materials shall conform to the manufacturers materials specifications for pumps. Asbestos, cadmium, and radio

18、active materials defined by Title 10, Code of Federal Regulations (CFR), Part 40, and other radioactive material in which the radioactivity is greater than 0.002 microcuries per gram or 0.01 microcuries total activity, shall not be incorporated into the pump assembly. 3.4 Environmental conditions. 3

19、.4.1 Storage temperature. The pump shall operate after being stored at temperatures ranging from 65 to +160 F. 3.4.2 Vibration resistance. The pump shall show no evidence of damage or leakage and shall meet the output requirements of 3.2.2 when subjected to a simple harmonic motion with an amplitude

20、 of not less than 0.03 inch at a frequency range of 10 to 55 Hz along each of the three mutually perpendicular axes. 3.4.3 Shock resistance. The pump shall show no evidence of damage or leakage and shall meet the output requirements of 3.2.2 when subjected to sawtooth wave shocks (see figure 5) of 2

21、5 gravity units (g) with a nominal duration of 18 milliseconds along each of the three mutually perpendicular axes. 3.4.4 Corrosion resistance. The pump shall resist corrosion resulting from exposure to salt fog . 3.4.5 Fungus resistance. The pump shall be non-nutritive for fungus growth. 3.5 Recycl

22、ed, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cyc

23、le costs. 3.6 Workmanship. Pump, fuel, electrical: 12 and 24 volt DC shall be processed in such a manner as to be uniform in quality and shall be free from other defects that will affect life, serviceability, or appearance. Provided by IHSNot for ResaleNo reproduction or networking permitted without

24、 license from IHS-,-,-A-A-59535A 4 4. REGULATORY REQUIREMENTS. The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with 23.403 of the Federal Acquisition Regulation (FAR). 5. PRODUCT CONFORMANCE PROVISIONS. 5.1 Product conformance. The pro

25、ducts provided shall meet the salient characteristics of this CID, conform to the producers own drawings, specifications, standards, and quality assurance practices, and be the same product offered for sale in the commercial market place. The Government reserves the right to require proof of such co

26、nformance 5.2 Certification. Certification must be done with the procuring activity approval. The contractor shall certify that the product offered meets the salient characteristics of the description and conforms to the producers own drawings, specifications, standards, and quality assurance practi

27、ces, and is the same as the product offered for sale in the commercial marketplace. The government reserves the right to require proof of such conformance prior to first delivery and thereafter as may be otherwise provided for under the provisions of the contract 6. PACKAGING. Preservation, packing,

28、 and marking shall be as specified in the contract or order. 7. NOTES. 7.1 PIN. The PIN should be used for Government purposes to buy commercial products to this CID. See section 2 for PIN format example. 7.2 Environmentally preferable material. Environmentally preferable materials should be used to

29、 the maximum extent possible to meet the requirements of this specification. As of the dating of this document, the U.S. Environmental Protection Agency (EPA) is focusing efforts on reducing 31 priority chemicals. The list of chemicals and additional information is available on their website http:/w

30、ww.epa.gov/osw/hazard/wastemin/priority.htm. Included in the EPA list of 31 priority chemicals are cadmium, lead, and mercury. Use of these materials should be minimized or eliminated unless needed to meet the requirements specified herein (see Section 3). 7.3 Commercial and Government Entity (CAGE)

31、 code. For ordering purposes, inventory control, and submission of these pump, fuel, electrical: 12 and 24 volt DC to DLA Land and Maritime under the Parts Management Advisory Team (PMAT), CAGE code 58536 should be used. 7.4 Source of documents. COMMERCIAL ITEM DESCRIPTION A-A-52557 - Fuel Oil, Dies

32、el; for Posts, Camps and Stations DEPARTMENT OF DEFENSE SPECIFICATION MIL-DTL -13486 - Cables, Special Purpose, Electrical: Low-Tension, Heavy-Duty, Single Conductor and Multiple Conductor, Shielded and Unshielded, General Specification for (Copies of these documents are available online at https:/a

33、ssistquicksearch.daps.mil/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59535A 5 FEDERAL REGULATIONS FAR Federal Acquisition Regula

34、tions (FAR) (Copies of these documents are available online at www.acquisition.gov/comp/far/index.html or from the U.S. Government Printing Office, 732 North Capital Street, NW, Washington D.C. 20401.) ASTM INTERNATIONAL ASTM D975 - Standard Specification for Diesel Fuel Oils ASTM D1655 - Standard S

35、pecification for Aviation Turbine Fuels ASTM D2000 - Standard Classification System for Rubber Products in Automotive Applications (Copies of these documents are available online at http:/www.astm.org or from the ASTM International, P.O. Box C700, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2

36、959.) 7.5 Ordering data. The contract or order should specify the following: a. CID document number, revision, and CID PIN. b. Product conformance provisions. c. Packaging requirements. 7.6 Commercial products. As part of the market analysis and research effort, this CID was coordinated with the fol

37、lowing manufacturers of commercial products. At the time of CID preparation and coordination, these manufacturers were known to have commercial products that would meet the requirements of this CID. (NOTE: This information should not be considered as a list of approved manufacturers or be used to re

38、strict acquisition to only the manufacturers shown.) MFRs CAGE MFRs name and address 0FWZ1 DAR Enterprises, Inc 2700 Rogan Rd Orlando, FL 32812-5828 (407) 896-7433 (407) 898-6066 0T0Y2 CME ARMA INC. 4500 NW 36THAVE MIAMI, FL 33142-4220 305-633-1524 Provided by IHSNot for ResaleNo reproduction or n

39、etworking permitted without license from IHS-,-,-A-A-59535A 6 MFRs CAGE MFRs name and address 0VW10 AM-MAC INCORPORATED 311 US HIGHWAY 46 STE C FAIRFIELD, NJ 07004-2419 973-575-7567 7Z016 KAMPI COMPONENTS CO. INC. 88 CANAL RD FAIRLESS HILLS, PA 19030-4302 215-736-2000 267-543-4002 7.7 Government

40、users. To acquire information on obtaining these pump, fuel, electrical: 12 and 24 volt DC from the Government inventory system, contact DLA Land and Maritime, ATTN DLA Land and Maritime Call Center (NAB), P.O. Box 3990, Columbus, OH 432183990 or telephone (614) 692-2271 or (614) 692-3191. 7.8 Legac

41、y. This commercial item description is a replacement for MIL-P-45328 and MS51321 for all federal agencies (MIL-P-45328 and MS51321 is canceled as of 30-APR-1993 and copies of these documents are available online at https:/assist.dla.mil/quicksearch/ or from the DLA Document Services Order Desk, 700

42、Robbins Avenue, Building 4D, Philadelphia, PA 191115094). 7.9 Cross reference table (See table II): TABLEII. Cross reference table. Pump type Former MS part number CID number I (12 volts) MS51321-1-12N1 AA59535-001 I (12 volts) MS51321-2-12N1 AA59535-001 II (24 volts) MS51321-3-24N1 AA59535-002 II (

43、24 volts) MS51321-1-24N1 AA59535-002 II (24 volts) MS51321-2-24N1 AA59535-002 7.10 Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extensiveness of the changes. Provided by IHSNot for ResaleNo reproductio

44、n or networking permitted without license from IHS-,-,-A-A-59535A 7 NOTE: Dimensions are in inches. Unless otherwise specified, tolerances are 0.010. FIGURE 1. Envelope dimensions for electrical fuel pump. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-

45、,-,-A-A-59535A 8 0 1 2 3 4 5 6 75101520253035DELIVERYGALLONSPER HOURPRESSURE - POUNDS PER SQUARE INCH18 VOLTS (TYPE I)30 VOLTS (TYPE II)FIGURE 2. Output performance curves. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59535A 9 5060708090100130

46、12011010k 100k 1M 10M 100MFREQUENCY (Hz)dBa/MHzFIGURE 3. Conducted emission limits. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59535A 10 FIGURE 4. Radiated emission limits. Provided by IHSNot for ResaleNo reproduction or networking permitted

47、 without license from IHS-,-,-A-A-59535A 11 0.3DD00.05P+0.05P+0.15P0.15P0.2P0.3P1.15P0.07DPIDEAL SAWTOOTH PULSETOLERANCE LIMITSP=PEAK VALUE IN GsD=NOMINAL DURATION IN MILLISECONDS (MS)FIGURE 5. Shock conditions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license fro

48、m IHS-,-,-A-A-59535A 12 MILITARY INTERESTS CIVIL AGENCY COORDINATING ACTIVITY: Custodians: GSA - FSS Army AT Navy-YD Air Force - 99 Preparing activity: DLA - CC DLA - CC Review activities: Project 2910-2014-003 Army-AR Navy- MC, SA Air Force - 71 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can