DLA A-A-59545-2001 JACKS DOLLY TYPE HYDRAULIC AUTOMOTIVE [Superseded DLA GGG-J-1564 C CANC NOTICE 1 DLA GGG-J-1564 C DLA GGG-J-1564 B DLA GGG-J-1564 A INT AMD 1 DLA GGG-J-1564 A DL.pdf

1、Beneficial comments (recommendations, additions, deletions) and any pertinent data that may be of usein improving this document should be addressed to: Defense Logistics Agency, Defense Supply Center,Columbus (DSCC-VAI), P.O. Box 3990, Columbus, OH 43216-5000.FSC 4910I NCH POUNDA-A-5954527 July 2001

2、SUPERSEDINGGGG-J-1564C31 March 1992COMMERCIAL ITEM DESCRIPTIONJACKS, DOLLY TYPE, HYDRAULIC, AUTOMOTIVEThe General Services Administration has authorized the use of thiscommercial item description for all federal agencies.1. SCOPE. This (CID) covers both manually operated and pneumatic assisted dolly

3、 typehydraulic jacks used for lifting automotive vehicles. These jacks are intended for use by themilitary and other government agencies for maintenance procedures on staff and tacticalvehicles.2. CLASSIFICATION. The hydraulic jacks covered by this CID are listed by type (minimum liftingcapacity) an

4、d style (manual operation and pneumatic assisted) (see 7.3).2.1 Types.Type I - 2 US ton load capacit yType II - 4 US ton load capacityType III - 10 US ton load capacityType IV - 20 US ton load capacity2.2 Style.Style A - Manual operation.B - Pneumatic assisted.3. SALIENT CHARACTERISTICS.3.1 Load cap

5、acities and dimensions . Jacks furnished under this CID shall meet the load liftingcapacities and dimensions of table I. Capacities and dimensions apply to both manual operatedand pneumatic assisted hydraulic jacks.Provided by IHSNot for ResaleNo reproduction or networking permitted without license

6、from IHS-,-,-A-A-595452TABLE I. Capacities and dimensions.TypesJack Characteristics(dimensions in inches unless otherwise specified) I II III IVLoad capacity US tons (minimum). 2 4 10 20Saddle in lowest position (measured to the highest point onthe saddle) (maximum). 5.50 5.50 6.50 8.50Saddle in the

7、 highest position (measured to the lowestpoint in the saddle) (minimum). 19.00 21.00 21.00 21.00Diameter of saddle (if shape is circular) (minimum). 6.00 6.50 6.50 6.50Size of saddle (area if saddle is not circular) measured insquare inches as seen from above (minimum). 28.27 33.18 33.18 33.183.2 De

8、sign . Jacks shall be new and shall meet all the requirements in this document andparagraphs 10-2.1 and 10-2.2 of ASME PALD (Safety Standard For Portable Automotive LiftingDevices). The standard referenced shall be the latest issue in effect. Pneumatic assisted jacksmust be capable of operating thro

9、ughout their full range and lifting the specified load without theuse of a pneumatic source.3.3 Overload capacity . Jacks shall meet the overload requirements of paragraph 10-2.3 ofASME PALD.3.4 Saddle periphery load . Jacks shall meet the requirements of paragraph 10-2.4 of ASMEPALD.3.5 Safety mark

10、ings and messages . Markings shall conform to section 10-3 of ASME PALD.3.6 Maintainability . Maintenance and adjustment of the jack shall require a minimum of skills andbe accomplished using common tools. Instructions for disassembly, repair, assembly andadjustment shall be clear and concise and in

11、cluded in a manual(s) supplied with each jack. Partsshall be clearly identified in an illustration that depicts part number, description, and quantity perassembly and reflects the relationship of an individual part to the complete assembly.3.7 Portability . Jacks must be equipped with wheels and cas

12、ters to permit easy movement andre-positioning of the jack on a hard level surface.3.8 Materials . Materials used shall be in accordance with the manufacturers specifications.When dissimilar metals are used in contact with each other, suitable protection against galvaniccorrosion shall be applied.3.

13、9 Workmanship . The jacks shall be fabricated and finished using commercially acceptableworkmanship standards.3.10 Painting . Painting and finishing shall be in accordance with industry practice. Beforepainting, all surfaces shall be clean and free of foreign matter detrimental to painting.3.11 Desi

14、gn Qualification . For each jack of a specific model, type or design sold to USgovernment agencies, a jack representative of that specific model, type or design shall be testedand shall meet the design qualification testing requirements as specified in section 10-4 of ASMEPALD. Following the Saddle

15、Periphery Test specified in 10-4.1.4, and with the jack in anunloaded condition, the jack frame shall be inspected for any permanent deformation. Permanentdeformation of the frame shall not result in a clearance between any wheel or caster and the floorProvided by IHSNot for ResaleNo reproduction or

16、 networking permitted without license from IHS-,-,-A-A595453equal to or greater than .125 inch. Any frame deformation found greater than specified above iscause for that jack design to be rejected and that specific jack design, type, or model not to besold to US government agencies.4. REGULATORY REQ

17、UIREMENTS. The offeror/contractor is encouraged to use recoveredmaterials to the maximum extent practicable, in accordance with paragraph 23.403 of the FederalAcquisition Regulation (FAR).5. PRODUCT CONFORMANCE.5.1 Product Conformance . The hydraulic jacks provided shall meet the salient characteris

18、tics ofthis CID, conform to the producers own drawings, specifications, standards and qualityassurance practices, and be the same product offered for sale in the commercial market. Thegovernment reserves the right to require proof of such conformance.5.2 Market Acceptability . The hydraulic jacks of

19、fered must have been sold to the government orcommercial market for a minimum of one year.6. PACKAGING. Preservation, packing, and marking shall be as specified in the contract ororder.7. NOTES.7.1 Part or Identification Number (PIN) . The following part or identification numbering procedureis for g

20、overnment purposes and does not constitute a requirement for the contractor.AA59545 - XX XStyle: A - Manual operationB - Pneumatic assistedType: I - 2 US ton load capacityII - 4 US ton lo ad capacityIII - 10 US ton load capacityIV - 20 US ton capacityCID number7.2 Source of Documents .7.2.1 A copy o

21、f the current version of ANSI/ASME PALD-1997 is available from the AmericanNational Standard s Institute (ANSI), 11 W 42nd Street, New York, NY 10036.7.2.2 The FAR may be obtained from the Superintendent of Documents, US GovernmentPrinting Office, Washington, D.C. 20402.7.3 Ordering data . The contr

22、act or order should specify the following:a. Number, ti tle and date of this CID.b. Type and Style required (see 2.1 and 2.2).c. Quantity ordered by type.d. Preservation, packing, and marking requirements (see 6).Provided by IHSNot for ResaleNo reproduction or networking permitted without license fr

23、om IHS-,-,-A-A5954547.4 Key words .CapacityHydraulicJackLiftingManualPALDPneumaticMILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY:GSA FSSCustodians: Preparing activity:Army - AR DLA - CCNavy -SHAir Force 99 (Project 4910-0826)DLA - CCReview activities:Army - ATNavy - SAProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-