DLA A-A-59562 A-2007 POST BINDING ELECTRICAL SCREW-TYPE (UNINSULATED)《螺旋式电气接线柱(非绝缘)》.pdf

1、Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any data that may improve this document should be sent to: STDZNMGTdla.mil or Defense Supply Center Richmond (DSCR), ATTN: DSCR-VEB, 8000 Jefferson Davis Highway, Richmond, VA 23297-5616. AMSC N/A FSC 5940 INCH-POUN

2、D A-A-59562A 22 March 2007 SUPERSEDING A-A-59562 23 June 2000 COMMERCIAL ITEM DESCRIPTION POST, BINDING, ELECTRICAL, SCREW-TYPE (UNINSULATED) The General Services Administration has authorized the use of this commercial item description for all federal agencies. 1. SCOPE. This commercial item descri

3、ption (CID) covers an uninsulated electrical binding post with insulated cap used as a wiring termination on terminal boards and test set panels. This binding post uses a screw-type wire gripping action. 2. CLASSIFICATION. The electrical binding post shall be classified and identified by the types i

4、n accordance with the characteristics specified in table I. The selected types of products to be supplied shall be specified in the acquisition order (see 7.3(b). TABLE I. Electrical binding post classifications and dimensions. Dimensions Type Color A1 B1 (max.)C1D1 E1 F1 I Black 0.562 0.734 0.312 6

5、-32 0.125 X 0.094 0.500 II Black 0.812 0.937 0.438 8-32 0.125 X 0.156 0.500 1See figure 1. 3. SALIENT CHARACTERISTICS 3.1 Components. The electrical binding post shall be similar to the one shown in figure 1. The product shall consist of the binding post, captive cap, and all mounting hardware. Prov

6、ided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59562A 2 NOTES: 1. The figure depicts only general characteristics and is not intended to limit specific manufacturing processes. 2. This is the insulated portion. Shape of insulated portion is optional

7、. 3. Dimensions (listed in table I) are in inches. Tolerance is 0.015 inch unless otherwise shown. FIGURE 1. Binding post configuration. 3.2 Materials. 3.2.1 Metal. Unless specified otherwise in the acquisition order (see 7.3(c), the current-carrying portions of the binding post shall be brass confo

8、rming to the requirements of ASTM B 16/B 16M, “Standard Specification for Free-Cutting Brass Rod, Bar and Shapes for Use in Screw Machines“. 3.2.2 Finish. Unless otherwise specified in the acquisition order (see 7.3(d), metal portions of the binding post shall be nickel plated in accordance with SAE

9、 AMS-QQ-N-290, “Nickel Plating (Electrodeposited)“. 3.2.3 Cap. The cap shall be insulated and non-removable. The material used for the insulated caps of the binding post shall be specified in the acquisition order (see 7.3(e). 3.3 Non-turn feature. Unless otherwise specified in the acquisition order

10、 (see 7.3(f), the non-turn feature shall be a knurled base as shown in figure 1. 4. REGULATORY REQUIREMENTS 4.1 Recovered materials. The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regul

11、ation (FAR). C F SEE NOTE 2 HEX NUT NO. 6-32 UNC-2B 0.109 X 0.312 ACROSS FLATS (TYPE I)HEX NUT NO. 8-32 UNC-2B 0.125 X 0.344 ACROSS FLATS (TYPE II)FLATWASHERINTERNAL-TOOTH LOCKWASHER D EAB (OPEN)Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-595

12、62A 3 5. PRODUCT CONFORMANCE PROVISIONS 5.1 Product conformance. The products provided shall meet the salient characteristics of this CID, conform to the producers own drawings, specifications, standards, and quality assurance practices, and be the same product offered for sale in the commercial mar

13、ketplace. The government reserves the right to require proof of such conformance. 5.2 Market acceptability. The product offered must have been previously sold either to the government or on the commercial market. 6. PACKAGING 6.1 Preservation, packing, and marking. Preservation, packing, and marking

14、 shall be as specified in the acquisition order (see 7.3(g). 7. NOTES 7.1 Part or identification number (PIN). The following PIN procedure is for government purposes and does not constitute a requirement for the contractor. 7.2 Sources of documents. 7.2.1 FAR. The FAR may be obtained from the Superi

15、ntendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250-7954. Electronic copies of FAR documents may be obtained from http:/www.arnet.gov/far/. 7.2.2 ASTM standards. Copies of ASTM standards may be obtained from ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 194

16、28-2959. Electronic copies of ASTM standards may be obtained from http:/www.astm.org/. 7.2.3 SAE standards. Copies of SAE standards may be obtained from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001. Electronic copies of SAE standards may be obtained from http:/www.sae.org/. T

17、ype 1 = type I (see table I) Type 2 = type II (see table I) AA59562 - X CID number Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59562A 4 7.3 Ordering data. The acquisition order should specify the following: a. CID document number, revision, a

18、nd CID PIN. b. Type required (see table I). c. Current-carrying material, if different (see 3.2.1). d. Binding post finish, if different (see 3.2.2). e. Insulation material (see 3.2.3). f. Non-turn feature, if different (see 3.3). g. Preservation, packing, and marking (see 6.1). 7.4 Subject term (ke

19、y word) listing. captive cap insulated cap terminal board test set panels wiring termination MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: Custodians: Army - CR Navy - EC Air Force - 11 GSA - FSS Review Activities: Army - AT, MI Navy - AS, MC, OS Air Force - 99 Preparing Activity: DLA - GS

20、2 (Project 5940-2006-003) NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-