ImageVerifierCode 换一换
格式:PDF , 页数:10 ,大小:69.07KB ,
资源ID:687549      下载积分:10000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-687549.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(DLA A-A-59582 C-2008 BEARING BALL ANNULAR SINGLE ROW RADIAL NON-FILLING SLOT DIMENSION SERIES 19《19尺寸系列的环形径向单排无装填槽滚珠轴承》.pdf)为本站会员(brainfellow396)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

DLA A-A-59582 C-2008 BEARING BALL ANNULAR SINGLE ROW RADIAL NON-FILLING SLOT DIMENSION SERIES 19《19尺寸系列的环形径向单排无装填槽滚珠轴承》.pdf

1、 METRIC A-A-59582C 05 August 2008 SUPERSEDING A-A-59582B 23 September 2003 Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any data COMMERCIAL ITEM DESCRIPTION BEARING, BALL, ANNULAR, SINGLE ROW, RADIAL, NON-FILLING SLOT, DIMENSION SERIES 19 The General Services

2、Administration has authorized the use of this commercial item description for all federal agencies. 1. SCOPE. This commercial item description (CID) covers metric, single row, radial, non-filling slot, annular ball bearings for general-purpose use. These bearings are not intended for use in critical

3、 aeronautical or critical special precision applications. 2. CLASSIFICATION. The ball bearings shall be classified by the class, sizes, cage materials, shield and seal configurations, precision tolerances, and lubricant and preservative requirements listed below: Class 5 - dimension series 19 Size -

4、 bearing dimensions (see table I) Cage materials (see table II) Shield and seal configurations (see table III) Precision tolerances (see table IV) Lubricant and preservative requirements (see table V) 3. SALIENT CHARACTERISTICS 3.1 Dimensions. Bearing boundary dimensions shall conform to the require

5、ments specified in table I for each of the coded bearing sizes. The listed dimensions conform to the requirements specified for the listed bearing sizes from dimension series 19 in the American Bearing Manufacturers Association (ABMA) Standard 20, “Radial Bearings of Ball, Cylindrical Roller, and Sp

6、herical Roller Types, Metric Design“. The bearing size shall be as specified in the acquisition order (see 7.3(b). For unlisted bearing sizes, the associated dimensional and dynamic load rating requirements should also be specified in the acquisition order. that may improve this document should be s

7、ent to: STDZNMGTdla.mil or Defense Supply Center Richmond (DSCR), ATTN: DSCR-VEB, 8000 Jefferson Davis Highway, Richmond, VA 23297-5616. AMSC N/A FSC 3110 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59582C 2 TABLE I. Dimensional requirements

8、(ABMA series 19). Bearing size code Bore diameter (mm) Outside diameter (mm) Width (mm) Chamfer r/min (mm) Minimum shaft shoulder diameter1(mm) Dynamic load rating (minimum) (lb.) 00 10 22 6 0.3 12 565 01 12 24 6 0.3 14 649 02 15 28 7 0.3 17 906 03 17 30 7 0.3 19 980 04 20 37 9 0.3 22 1,427 05 25 42

9、 9 0.3 27 1,490 06 30 47 9 0.3 32 1,629 07 35 55 10 0.6 39 2,150 08 40 62 12 0.6 44 3,100 09 45 68 12 0.6 49 3,150 10 50 72 12 0.6 54 3,259 11 55 80 13 1.0 60 3,570 12 60 85 13 1.0 65 3,700 13 65 90 13 1.0 70 3,890 14 70 100 16 1.0 75 5,110 15 75 105 16 1.0 80 5,440 16 80 110 16 1.0 85 5,590 17 85 1

10、20 18 1.1 91.5 7,150 18 90 125 18 1.1 96.5 7,310 19 95 130 18 1.1 101.5 7,550 20 100 140 20 1.1 106.5 9,250 21 105 145 20 1.1 111.5 9,460 22 110 150 20 1.1 116.5 9,790 24 120 165 22 1.1 126.5 11,900 26 130 180 24 1.5 138 14,600 28 140 190 24 1.5 148 14,900 30 150 210 28 2.0 159 19,000 32 160 220 28

11、2.0 169 19,500 34 170 230 28 2.0 179 19,300 36 180 250 33 2.0 189 26,600 38 190 260 33 2.0 199 26,300 40 200 280 38 2.1 211 32,100 1Listed for reference purposes only. Shoulder height shall be determined to provide sufficient clearance for the direct application of bearing removal force against the

12、bearing inner ring. If the required minimum clearance is not available, an alternative non-destructive bearing removal capability shall be provided. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59582C 3 3.2 Materials. 3.2.1 Rings. The bearing

13、ring material shall be chromium-alloy steel 52100 (UNS G52986) as specified in ASTM International (ASTM) A 295/A 295M, “Standard Specification for High-Carbon Anti-Friction Bearing Steel“. The finished rings shall not exceed the associated billet material inclusion rating that is also specified in A

14、STM A 295/A 295M. Ring hardness shall be at least 58 HRC as defined in ASTM E 18, “Standard Test Methods for Rockwell Hardness of Metallic Materials“. The grain size of the ring material shall be determined in accordance with ASTM E 112, “Standard Methods for Determining Average Grain Size“. 3.2.2 B

15、alls. The bearing ball material shall be chromium-alloy steel 52100 (UNS G52986) as specified in ASTM A 295/A 295M. The finished balls shall not exceed the associated billet material inclusion rating, which is also specified in ASTM A 295/A 295M. Balls shall be through-hardened no less than 60 HRC a

16、nd no more than 67 HRC as defined in ASTM E 18. The grain size of the ball material shall be determined in accordance with ASTM E 112. 3.2.3 Cage. The bearing cage material shall be impervious to deterioration from any lubricant, preservative, solvent, or other chemical substance expected to contact

17、 the bearing during normal use or storage. Similarly, the material shall not cause any chemical deterioration of any other bearing component. Metallic cage materials shall operate from -40 F to 250 F (-40 C to 121 C). Non-metallic cage materials shall operate from -20 F to 250 F (-30 C to 121 C). Un

18、less otherwise specified in the acquisition order, the cage material shall be one of the optional coded types listed in table II (see 7.3(c). TABLE II. Cage materials. Code1Material type J Pressed steel M Machined bronze or brass P Molded plastic (nylon 6/6 or equal) T Machined non-metallic (phenoli

19、c) Y Pressed brass X Other 1No significant changes from FF-B-171/2. 3.2.4 Shields and seals. When used, the shield or seal material shall be as recommended by the manufacturer, unless otherwise specified in the acquisition order (see 7.3(d). The material shall be impervious to deterioration from any

20、 lubricant, preservative, solvent, or other chemical substance expected to contact the bearing during normal use or storage. Similarly, the material shall not cause any chemical deterioration of any other bearing component. The shield or seal shall remain functionally effective at a minimum temperat

21、ure range of -20 F to 250 F (-30 C to 121 C) for non-metallic and -40 F to 250 F (-40 C to 121 C) for metallic materials. Unless otherwise specified in the acquisition order, the shield and seal configuration for the bearing shall be one of the coded options listed in table III (see 7.3(e). Provided

22、 by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59582C 4 TABLE III. Shield and seal configurations. Code1Configuration option A Open B Single shield C Double shield D Single seal E Double seal F Single shield and seal X Other (specify in acquisition orde

23、r) 1No significant changes from FF-B-171/2. 3.3 Precision tolerance. The bearing precision tolerance level shall conform to Annular Bearing Engineers Committee (ABEC) class ABEC-1, ABEC-3, ABEC-5, or ABEC-7 as defined in ABMA Standard 20. The tolerance class and associated radial internal clearance

24、shall be one of the coded options listed in table IV (see 7.3(f). TABLE IV. Precision tolerance requirements. Code Tolerance class Radial internal clearance A Group 2 (less than normal) B Group N (normal) C Group 3 (greater than normal) D Group 4 (greater than group 3) T ABEC-1 Group 5 (greater than

25、 group 4) E Group 2 (less than normal) F Group N (normal) G Group 3 (greater than normal) H Group 4 (greater than group 3) U ABEC-3 Group 5 (greater than group 4) J Group 2 (less than normal) K Group N (normal) L Group 3 (greater than normal) M Group 4 (greater than group 3) V ABEC-5 Group 5 (greate

26、r than group 4) N Group 2 (less than normal) P Group N (normal) R Group 3 (greater than normal) S Group 4 (greater than group 3) W ABEC-7 Group 5 (greater than group 4) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59582C 5 3.3.1 Bearing precis

27、ion tolerance levels and internal clearances may be affected by the addition of shields and/or seals. Manufacturers/suppliers should be consulted for availability of desired precision tolerances when shields and/or seals are required. 3.4 Lubrication and preservation requirements. Unless otherwise s

28、pecified in the acquisition order, the bearing lubricant or preservative requirement shall be as selected from the approved coded options listed in table V (see 7.3(g). When grease fill is required, the bearing void (the airspace between the inner and outer rings of the assembled bearing) shall be 2

29、5 to 50 percent filled. Bearing preservative shall be in accordance with MIL-DTL-197, “Packaging of Bearings, Associated Parts and Subassemblies“. TABLE V. Lubricant and preservative requirements. Code Lubricant or preservative compound B Grease in accordance with MIL-PRF-81322 E Grease in accordanc

30、e with DOD-G-24508 H Grease in accordance with MIL-PRF-23827 L Grease with SRI-2 or qualified equivalent S No fill T Preservation compound in accordance with MIL-DTL-197 X Other (specify in the acquisition order) 4. REGULATORY REQUIREMENTS 4.1 Recovered materials. The offeror/contractor is encourage

31、d to use recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 4.2 Unless otherwise specified in the solicitation and resulting contract, the foreign acquisition restrictions in Section 252.225, Clause 252.225.7016 of

32、the Defense Federal Acquisition Regulation Supplement (DFARS) apply to products described by this CID. 5. PRODUCT CONFORMANCE PROVISIONS 5.1 Product conformance. The products provided shall meet the salient characteristics of this commercial item description, conform to the producers own drawings, s

33、pecifications, standards, and quality assurance practices, and be the same product offered for sale in the commercial marketplace. The government reserves the right to require proof of such conformance. 5.2 Market acceptability. The product offered must have been previously sold either to the govern

34、ment or on the commercial market. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59582C 6. PACKAGING 6.1 Preservation, packing, and marking. Unless otherwise specified in the acquisition order, the bearings supplied shall be preserved, packed, a

35、nd marked in accordance with MIL-DTL-197 (see 7.3(h). 7. NOTES 7.1 Part or identification number (PIN). The following PIN numbering procedure is for government purposes and does not constitute a requirement for the contractor. AA59582 - 5 08 J C K B Example of reference part number: Lubricant and pr

36、eservative code (see table V) Precision tolerance code (see table IV) Shield and seal code (see table III) Cage material code (see table II) Bearing size code (see table I) Class 5 - dimension series 19 CID number AA59582 - 5 08 J C K B indicates: boundary dimension series 19; bore diameter 40 mm, o

37、utside diameter 62 mm, width 12 mm; pressed steel cage; double shield; ABEC-5 tolerance class, normal radial internal clearance; filled with grease in accordance with MIL-PRF-81322. 7.2 Sources of documents. 7.2.1 ABMA standards. Copies of ABMA standards may be obtained from the American Bearing Man

38、ufacturers Association, 2025 M Street NW, Suite 800, Washington, DC 20036. Electronic copies of ABMA standards may be obtained from http:/www.abma-dc.org/. 7.2.2 ASTM standards. Copies of ASTM standards may be obtained from ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken,

39、 PA 19428-2959. Electronic copies of ASTM standards may be obtained from http:/www.astm.org/. 7.2.3 FAR and DFARS. Copies of the FAR and DFARS may be obtained from the Superintendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250-7954. Electronic copies of the FAR may be obtained from http:/www

40、.arnet.gov/far/. Electronic copies of the DFARS may be obtained from http:/www.acq.osd.mil/dp/dars/dfars.html. 7.2.4 Military specifications and standards. Copies of military specifications and standards may be obtained from Standardization Documents Order Desk, 700 Robbins Avenue, Building 4D, Phil

41、adelphia, PA 19111-5094. Electronic copies of military specifications and standards may be obtained from http:/assist.daps.dla.mil/quicksearch/. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59582C 7 7.3 Ordering data. Acquisition documents s

42、hould specify the following information: a. CID document number, revision, and CID PIN. b. Bearing size (with dimension/load requirements if size is unlisted) (see 3.1). c. Cage material type (see 3.2.3). d. Shield or seal material (see 3.2.4). e. Shield and seal configuration (see 3.2.4). f. Precis

43、ion tolerance requirement (see 3.3). g. Lubricant and preservative requirements (see 3.4). h. Preservation, packing, and marking requirements (see 6.1). 7.4 Codes cross-reference. Tables VI, VII, and VIII contain cross-reference data for the PIN information as listed in FF-B-171/2 and this CID. 7.4.

44、1 Bearing class designations. The CIDs replacing 33 of the 37 associated specification sheets of FF-B-171 have been assigned class codes corresponding to ABMA dimension series. Table VI lists the FF-B-171 specification sheets, the corresponding dimension series, the CID class codes, and the replacem

45、ent CIDs. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59582C 8 TABLE VI. Federal specification to CID cross-reference. FF-B-171 specification sheets ABMA dimension series CID class codes Replacement CID numbers 1 02, 03, 10 1, 2, 4 A-A-59581

46、2 19 5 A-A-59582 3 10 4 A-A-59583 4 02 1 A-A-59584 5 03 2 A-A-59585 6 04 3 A-A-59586 7 02 1 A-A-59587 8 03 2 A-A-59589 9 32 8 A-A-59595 10 33 9 A-A-59596 11 02 1 A-A-59597 12 03 2 A-A-59598 13 22 6 A-A-59599 14 23 7 A-A-59600 15 19 - Canceled 16 10 - Canceled 17 02 - Canceled 18 03 - Canceled 19 19

47、5 A-A-59623 20 10 4 A-A-59624 21 02 1 A-A-59625 22 03 2 A-A-59626 23 04 3 A-A-59627 24 10 4 A-A-59628 25 02 1 A-A-59629 26 03 2 A-A-59630 27 04 3 A-A-59631 28 10 4 A-A-59632 29 02 1 A-A-59633 30 03 2 A-A-59634 31 04 3 A-A-59635 32 32 8 A-A-59636 33 33 9 A-A-59637 34 32 8 A-A-59638 35 33 9 A-A-59639

48、36 32 8 A-A-59640 37 33 9 A-A-59641 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59582C 9 TABLE VII. Radial internal clearance and ABEC tolerance codes. FF-B-171/2 codes A-A-59582C codes Code Radial internal clearance Tolerance class Code Tole

49、rance class Radial internal clearance 1 Symbol 2 A Group 2 2 Symbol 0 B Group N 3 Symbol 3 C Group 3 4 Symbol 4 D Group 4 ABEC-1 T ABEC-1 Group 5 E Group 2 F Group N G Group 3 H Group 4 U ABEC-3 Group 5 5 Symbol 2 J Group 2 6 Symbol 0 K Group N 7 Symbol 3 L Group 3 8 Symbol 4 M Group 4 ABEC-5 V ABEC-5 Group 5 N Group 2

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1