DLA A-A-59590 12 B-2010 HOLDER ELECTRICAL CARD WEDGE RETAINERS 3 PIECE SCREW ACTUATED DRIVE 240 X 180 INCH BODY SIZE WITH SCREW RETENTION.pdf

1、INCHPOUND AA59590/12B 12 October 2010 SUPERSEDING AA59590/12A 19 January 2006 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET HOLDER, ELECTRICAL CARD, WEDGE RETAINERS, 3 PIECE, SCREW ACTUATED DRIVE, .240 X .180 INCH BODY SIZE, WITH SCREW RETENTION The General Services Administration has authorized t

2、he use of this commercial item description for all federal agencies. The complete requirements for procuring electrical card holders described herein shall consist of this document and the latest issue in effect of AA59590. CLASSIFICATION/PART IDENTIFICATION NUMBER (PIN). This commercial item descri

3、ption (CID) specification sheet uses a classification system which is included in the Part Identification Number (PIN) as shown in the following example (see notes). AA59590 CID number /12 Applicable CID specification sheet * Finish * Mounting * * Length (see table I) W, D, E Configuration (see tabl

4、e II) Example: AA59590/12CT48 is the PIN for a chemical film finished, 4.8 inch long card holder with a lock nut on the screw for captivation. The card holder also features two tapped mounting holes for use with 080 UNF fasteners. SALIENT CHARACTERISTICS. Performance. Card holders shall hold the cir

5、cuit card assembly firmly in its installed position. When the card holder is installed properly, it is capable of withstanding 60g/6ms of shock, 25 G-rms of vibration, and provides from 2 to 4 degrees C/W/inch thermal resistance transfer between the circuit card assembly and the heat sink surfaces.

6、Material. Unless otherwise specified herein, the card holder materials shall be as specified in AA59590. Interface and physical dimensions. The card holders supplied to this CID specification sheet shall be as specified on figures 1, 2, 3, 4, in table I, and AA59590. Actuating screw hex drive socket

7、. The across flats dimension for the hex drive socket shall be as follows: .094 inch (2.38 mm) for mounting options “J“, “N“, “T“, “R“, “V“, and “S“ and 2.5 mm (.098 inch) for mounting options “G“ and “M“. Screw retention (locknut). The screw retention feature intended to prevent unintentional disas

8、sembly of the card holder shall be as specified in figure 2. The locknut shall be fabricated of a corrosion resistant material. Nominal installation torque. When card holders are used in cold plate applications, the nominal installation torque of each card holder shall be 4 to 6 inch-pounds (0.45 to

9、 0.68 N-m). Cold plate slot width dimensions (when applicable). The recommended cold plate slot width to accommodate the circuit card assembly with attached card holder is .210 inch (5.33 mm) plus the thickness of the printed board of the circuit card assembly (see AA59590). AMSC N/A FSC 5998Provide

10、d by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/12B 2 Inches mm Inches mm Inches mm .08 .180 2.0 4.57 .220 .240 5.59 6.1 .42 10.7 NOTES: 1. Dimensions are in inches. Millimeters are given for general information only. 2. Unless otherwise specified,

11、tolerances are .02 inch (0.5 mm) for two place decimals and .010 inch (0.25 mm) for three place decimals. 3. Dimension shall be .20 inch (5.1 mm) maximum on card holders without option “W“ or “D“ and .30 inch (7.6 mm) maximum on card holders with option “W“ or “D“. 4. The across flats dimension for

12、hex drive socket shall be .094 inch (2.38 mm) for mounting options “J“, “K“, “N“, “T“, “R“, “V“, and “S“. The across flats dimension for hex drive socket shall be a metric dimension of 2.5 mm (.098 inch) across flats for mounting options “G“ and “M“. FIGURE 1. Relaxed and expanded dimensions. FIGURE

13、 2. Screw retaining self-locking nut (corrosion resistant) details. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/12B 3 Finish. The finish options shall be as specified in AA59590. The finish options available for this specification sheet a

14、re as follows: “B“ (black anodize), “C“ (gold chemical film), “E“ (electroless nickel), “H“ (hard black anodize), and “R“ (clear chemical film). Mounting. The mounting options shall be as specified in AA59590. The mounting options available for this specification sheet are as follows: “J“ (rivet mou

15、nting holes), “N“ (no mounting holes), “T“ or “R“ (tapped 0-80 UNF 2B holes), “V“ or “S“ (tapped 2-56 UNC 2B holes), or “G“ or “M“ (tapped M2.5 x.45 metric holes). Card holders using mounting option “J“ may be shipped unassembled. Rivet mounting holes. The holes used for rivet mounting shall be .066

16、 to .073 inch (1.68 to 1.85 mm) diameter through holes, countersunk 100 degrees by .140 inch (3.56 mm) diameter with an access/clearance counterbore hole of .156 inch (3.96 mm) diameter by .130 to .140 inch (3.30 to 3.56 mm) deep. Mounting hole locations (when required). Two mounting holes are requi

17、red on card holders less than 5.30 inches (134.6 mm) in length. Three mounting holes are required on card holders 5.30 inches (134.6 mm) or greater in length. The third mounting hole shall be centered on the mounting body. See figure 1 and table I for mounting hole locations and spacing requirements

18、. Length, expanded, and relaxed dimensions. The length, expanded, and relaxed dimensions shall be as specified on figure 1. The length designator shall be as specified in AA59590 and the available lengths for this specification sheet are listed in table I. TABLE I. Additional assembly dimensions (se

19、e figures 1 and 2). 1/ PIN length designator Dimension “LENGTH“ .02 (0.5) Dimension “A“ (maximum) Dimension “B“ .02 (0.5) Dimension “C“ .005 (0.13) Dimension “D“ .01 (0.3) Without options “W“ or “D“ With options “W“ or “D“ 18 1.8 (45.7) 2.10 (53.3) 2.20 (55.9) .95 (24.1) .40 (10.2) .275 (6.99) 23 2.

20、3 (58.4) 2.60 (66.0) 2.70 (68.6) 1.45 (36.8) .70 (17.8) .370 (9.39) 28 2.8 (71.1) 3.10 (78.7) 3.20 (81.3) 1.95 (49.5) .90 (22.9) .525 (13.3) 30 3.0 (76.2) 3.30 (83.8) 3.40 (86.4) 2.15 (54.6) 1.10 (27.9) .525 (13.3) 33 3.3 (83.8) 3.60 (91.4) 3.70 (94.0) 2.45 (62.2) 1.40 (35.6) .525 (13.3) 35 3.5 (88.

21、9) 3.80 (96.5) 3.90 (99.1) 2.65 (67.3) 1.60 (40.6) .525 (13.3) 38 3.8 (96.5) 4.10 (104.1) 4.20 (106.7) 2.95 (74.9) 1.90 (48.3) .525 (13.3) 40 4.0 (101.6) 4.30 (109.2) 4.40 (111.8) 3.15 (80.0) 2.10 (53.3) .525 (13.3) 43 4.3 (109.2) 4.60 (116.8) 4.70 (119.4) 3.45 (87.6) 2.40 (60.9) .525 (13.3) 45 4.5

22、(114.x) 4.80 (121.9) 4.90 (124.5) 3.65 (92.7) 2.60 (66.0) .525 (13.3) 48 4.8 (121.9) 5.10 (129.5) 5.20 (132.1) 3.95 (100.3) 2.90 (73.7) .525 (13.3) 50 5.0 (127.0) 5.30 (134.6) 5.40 (137.2) 4.15 (105.4) 3.10 (78.7) .525 (13.3) 53 5.3 (134.6) 5.60 (142.2) 5.70 (144.8) 4.45 (113.0) 3.40 (86.4) .525 (13

23、.3) 58 5.8 (147.3) 6.10 (154.9) 6.20 (157.5) 4.95 (125.7) 3.90 (99.1) .525 (13.3) 1/ Dimensions are in inches. Millimeters, in parenthesis, are given for general information only. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/12B 4 Configur

24、ation. The configuration of a card holder shall be as specified in table II. The details of a particular configuration consist of those on figures 1, 2, 3, and 4. Card holders not requiring the options described by table II shall leave the configuration position in the PIN blank. TABLE II. Configura

25、tions. Configuration Applicable figures Hardware options - 1 and 2 No added options W 1, 2 and 3 Lockwasher and flat washer E 1, 2 and 4 Screw self-locking element D 1, 2, 3 and 4 Lockwasher, flat washer and screw self-locking element Lockwasher and flat washer (see figure 3). The use of a lockwashe

26、r and flat washer located under the screw head will provide additional resistance to loosening from shock and vibration. Card holders requiring a lockwasher and flat washer shall include a suffix “W“ in the PIN (see classification and notes). FIGURE 3. Lockwasher and flat washer details. Screw self-

27、locking element (see figure 4). The use of a screw self-locking element will provide prevailing torque for resistance to loosening from shock and vibration. Card holders requiring a screw self-locking element shall include a suffix “E“ in the PIN (see classification and notes). FIGURE 4. Screw self-

28、locking element details. Lockwasher, flat washer, and screw self-locking element. Card holders requiring a lockwasher, flat washer, and screw self-locking element configuration shall include a suffix “D“ in the PIN (see classification and notes). NOTES. PIN. The PIN should be used for Government pur

29、poses to buy commercial products to this CID specification sheet. See the classification section for PIN format example. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/12B 5 Source of documents. Commercial Item Description AA59590 Holder, El

30、ectrical Card, Wedge Retainers, 3 Piece, Screw Actuated Drive, General Requirements For. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or https:/assist.daps.dla.mil/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philade

31、lphia, PA 191115094.) Ordering data. Ordering data is as specified in AA59590. Commercial products. As part of the market analysis and research effort, this CID specification sheet was coordinated with the following manufacturers of commercial products. At the time of preparation and coordination of

32、 this CID specification sheet, these manufacturers were known to have commercial products that would meet the requirements of this CID specification sheet. (NOTE: This information should not be considered as a list of approved manufacturers or be used to restrict procurement to only the manufacturer

33、s shown.) Manufacturer CAGE Manufacturer name and address Manufacturer contact information 18915 Birtcher A Division of Pentair Electronic Packaging 7328 Trade Street San Diego, CA 921213410 Telephone: (858) 7402400 Toll Free: (800) 8547086 Facsimile: (858) 7402430 (URL): 61081 Calmark A Division o

34、f Pentair Electronic Packaging 7328 Trade Street San Diego, CA 921213410 Telephone: (858) 7402400 Toll Free: (800) 8547086 Facsimile: (858) 7402430 Electronic mail: URL: 5BG68 Card Locks Unlimited, Inc. 2310 E. Orangethorpe Avenue Anaheim, CA 928061231 Telephone: (714) 7386194 Facsimile: (714) 446

35、0119 E-mail: URL: Part number supersession data. This CID specification sheet PINs supersedes the following manufacturers part numbers as shown in table III. The CID PINs listed in table III are only for length designator “28“. See table IV for CID PIN construction using other available lengths fo

36、r this specification sheet. This information is being provided to assist in reducing proliferation in the Government inventory system. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/12B 6 TABLE III. Commercial part number supersession data.

37、PIN designator AA59590/12 Vendor similar designator or type part number 1/ CAGE 18915 Vendor similar designator or type part number 1/ CAGE 61081 Vendor similar designator or type part number 1/ CAGE 5BG68 BJ28 416BLN A2402.80H 3240BA2.80HR BN28 416BLNA A2402.80 3240BA2.80R BT28 416BLNT A2402.80T0 3

38、240BA2.80T0R BV28 416BLNS A2402.80T2 3240BA2.80T2R BG28 416BLNM MA2402.80TM2.5 3240MBA2.80TM2.5R BJ28E 416BLNL A2402.80HL 3240BA2.80HLR BN28E 416BLNAL A2402.80L 3240BA2.80LR BT28E 416BLNTL A2402.80T0L 3240BA2.80T0LR BV28E 416BLNSL A2402.80T2L 3240BA2.80T2LR BG28E 416BLNML MA2402.80TM2.5L 3240MBA2.80

39、TM2.5LR BJ28W 416BLFLN WA2402.80H 3240WBA2.80HR BN28W 416BLFLNA WA2402.80 3240WBA2.80R BT28W 416BLFLNT WA2402.80T0 3240WBA2.80T0R BV28W 416BLFLNS WA2402.80T2 3240WBA2.80T2R BG28W 416BLFLNM MWA2402.80TM2.5 3240MWBA2.80TM2.5R BJ28D 416BLFLNL WA2402.80HL 3240WBA2.80HLR BN28D 416BLFLNAL WA2402.80L 3240W

40、BA2.80LR BT28D 416BLFLNTL WA2402.80T0L 3240WBA2.80T0LR BV28D 416BLFLNSL WA2402.80T2L 3240WBA2.80T2LR BG28D 416BLFLNML MWA2402.80TM2.5L 3240MWBA2.80TM2.5LR CJ28 416LN 2402.80HR 3240CG2.80HR CN28 416LNA 2402.80R 3240CG2.80R CT28 416LNT 2402.80T0R 3240CG2.80T0R CV28 416LNS 2402.80T2R 3240CG2.80T2R CG28

41、 416LNM M2402.80TM2.5R 3240MCG2.80TM2.5R CJ28E 416LNL 2402.80HLR 3240CG2.80HLR CN28E 416LNAL 2402.80LR 3240CG2.80LR CT28E 416LNTL 2402.80T0LR 3240CG2.80T0LR CV28E 416LNSL 2402.80T2LR 3240CG2.80T2LR CG28E 416LNML M2402.80TM2.5LR 3240MCG2.80TM2.5LR See footnote at end of table. Provided by IHSNot for

42、ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/12B 7 TABLE II. Commercial part number supersession data Continued. PIN designator AA59590/12 Vendor similar designator or type part number 1/ CAGE 18915 Vendor similar designator or type part number 1/ CAGE 61081 Ven

43、dor similar designator or type part number 1/ CAGE 5BG68 CJ28W 416LFLN W2402.80HR 3240WCG2.80HR CN28W 416LFLNA W2402.80R 3240WCG2.80R CT28W 416LFLNT W2402.80T0R 3240WCG2.80T0R CV28W 416LFLNS W2402.80T2R 3240WCG2.80T2R CG28W 416LFLNM MW2402.80TM2.5R 3240MWCG2.80TM2.5R CJ28D 416LFLNL W2402.80HLR 3240W

44、CG2.80HLR CN28D 416LFLNAL W2402.80LR 3240WCG2.80LR CT28D 416LFLNTL W2402.80T0LR 3240WCG2.80T0LR CV28D 416LFLNSL W2402.80T2LR 3240WCG2.80T2LR CG28D 416LFLNML MW2402.80TM2.5LR 3240MWCG2.80TM2.5LR EJ28 416ENLN EN2402.80HR 3240EN2.80HR EN28 416ENLNA EN2402.80R 3240EN2.80R ET28 416ENLNT EN2402.80T0R 3240

45、EN2.80T0R EV28 416ENLNS EN2402.80T2R 3240EN2.80T2R EG28 416ENLNM MEN2402.80TM2.5R 3240MEN2.80TM2.5R EJ28E 416ENLNL EN2402.80HLR 3240EN2.80HLR EN28E 416ENLNAL EN2402.80LR 3240EN2.80LR ET28E 416ENLNTL EN2402.80T0LR 3240EN2.80T0LR EV28E 416ENLNSL EN2402.80T2LR 3240EN2.80T2LR EG28E 416ENLNML MEN2402.80T

46、M2.5LR 3240MEN2.80TM2.5LR EJ28W 416ENLFLN WEN2402.80HR 3240WEN2.80HR EN28W 416ENLFLNA WEN2402.80R 3240WEN2.80R ET28W 416ENLFLNT WEN2402.80T0R 3240WEN2.80T0R EV28W 416ENLFLNS WEN2402.80T2R 3240WEN2.80T2R EG28W 416ENLFLNM MWEN2402.80TM2.5R 3240MWEN2.80TM2.5R EJ28D 416ENLFLNL WEN2402.80HLR 3240WEN2.80H

47、LR EN28D 416ENLFLNAL WEN2402.80LR 3240WEN2.80LR ET28D 416ENLFLNTL WEN2402.80T0LR 3240WEN2.80T0LR EV28D 416ENLFLNSL WEN2402.80T2LR 3240WEN2.80T2LR EG28D 416ENLFLNML MWEN2402.80TM2.5LR 3240MWEN2.80TM2.5LR See footnote at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/12B 8 TABLE II. Commercial par