DLA A-A-59590 2 C-2010 HOLDER ELECTRICAL CARD WEDGE RETAINERS 3 PIECE SCREW ACTUATED DRIVE 225 X 260 INCH BODY SIZE WITH EJECTION ACTION.pdf

1、INCHPOUND AA59590/2C 2 October 2010 SUPERSEDING AA59590/2B 20 April 2007 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET HOLDER, ELECTRICAL CARD, WEDGE RETAINERS, 3 PIECE, SCREW ACTUATED DRIVE, .225 X .260 INCH BODY SIZE, WITH EJECTION ACTION The General Services Administration has authorized the us

2、e of this commercial item description for all federal agencies. The complete requirements for procuring electrical card holders described herein shall consist of this document and the latest issue in effect of AA59590. CLASSIFICATION/PART IDENTIFICATION NUMBER (PIN). This commercial item description

3、 (CID) specification sheet uses a classification system which is included in the Part Identification Number (PIN) as shown in the following example (see notes). AA59590 CID number /02 Applicable CID specification sheet * Finish * Mounting * * Length (see table I) W, D, E Configuration (see table II)

4、 Example: AA59590/02BG28D is the PIN for a black anodized, 2.8 inches (71 mm) long card holder with a flat washer, lockwasher, and screw self-locking element. The card holder also features two tapped mounting holes for use with metric M2.5 x 0.45 fasteners. SALIENT CHARACTERISTICS. Performance. Card

5、 holders shall hold the circuit card assembly firmly in its installed position and provide high resistance to loosening due to shock and vibration. Card holders shall also provide maximum thermal transfer from the circuit card assembly to the cold plate or heat sink surfaces. Material. Unless otherw

6、ise specified herein, the card holder materials shall be as specified in AA59590. Interface and physical dimensions. The card holders supplied to this CID specification sheet shall be as specified herein (see figures 1, 2, 3, 4, and table I) and meet the general requirements of CID AA59590. Card hol

7、ders shall have an ejection action feature that forces the circuit card assembly to disengage from its installed position. Actuating screw hex drive socket. The across flats dimension for the hex drive socket shall be as follows: .094 inch (2.38 mm) for mounting options “J“, “K“, “N“, “T“, “R“, “V“,

8、 and “S“ and 2.5 mm (0.098 inch) for mounting options “G“ and “M“. Cold plate slot width dimensions. The recommend cold plate slot width to accommodate the circuit card assembly with attached card holder is .300 inch (7.62 mm) plus the thickness of the printed board of the circuit card assembly (see

9、 AA59590). Nominal installation torque. When card holders are used in cold plate applications, the nominal installation torque of each card holder shall be as follows: 6 inch-pounds (0.68 N-m) for assemblies using no options or option “W“ and 8 inch-pounds (0.9 N-m) for assemblies using options “D“

10、or “E“. AMSC N/A FSC 5998 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/2C 2 Inches mm Inches mm Inches mm Inches mm .225 5.72 .25 .250 6.4 6.35 .270 .325 6.86 8.26 .62 .95 15.7 24.1 NOTES: 1. Dimensions are in inches. Millimeters are given

11、 for general information only. 2. Unless otherwise specified, tolerances are .02 inch (0.51 mm) for two place decimals and .010 inch (0.25 mm) for three place decimals. 3. The tolerance for the mounting hole spacing is .005 inches (0.13 mm). 4. The across flats dimension for hex drive socket shall b

12、e .094 inch (2.39 mm) for mounting options “J“, “N“, “T“, and “V“. The across flats dimension for hex drive socket shall be a metric dimension of 2.5 mm (.098 inch) across flats for mounting option “G“. FIGURE 1. Relaxed and expanded dimensions. Provided by IHSNot for ResaleNo reproduction or networ

13、king permitted without license from IHS-,-,-AA59590/2C 3 Ejection action (see figure 2). The ejection action shall allow for the initial ejection of the circuit card assembly from its installed position without damaging circuits, components, or the mating connector(s). The minimal amount of ejection

14、 distance shall be .25 inch (6.4 mm). FIGURE 2. View of assembly installed and ejected. Finish. The finish designator shall be as specified in AA59590. The finishes available for this CID specification sheet are as follows: “B“ (black anodize), “C“ (gold chemical film), “E“ (electroless nickel), or

15、“H“ (hard black anodize). Mounting. The mounting designators shall be as specified in AA59590. Except when using mounting option “N“, two mounting holes are required on the card holders. The mounting options available for this CID specification sheet are as follows: “J“ (rivet mounting holes), “N“ (

16、no mounting holes), “T“ (tapped 0-80 UNF 2B holes), “V“ (tapped 2-56 UNC 2B holes), or “G“ (tapped M2.5 x.45 metric holes). See figure 1 and table I for mounting hole spacing requirements. Card holders using mounting option “J“ may be shipped unassembled. Counterbore holes (for rivet mounting). The

17、holes used for rivet mounting shall be .066/.073 inch (1.68/1.85 mm) diameter, countersunk 100 degrees by .140 inch (3.56 mm) diameter through holes with an access/clearance counterbore of .156 inch (3.96 mm) diameter by .200 inch (5.08 mm) deep. Rivets. This card holder uses rivet style B as specif

18、ied in AA59590 when rivet mounting is used. Length, expanded, and relaxed dimensions. The length, expanded, and relaxed dimensions shall be as specified on figure 1. The length designator shall be as specified in AA59590 and the lengths available for this CID specification sheet are listed in table

19、I. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/2C 4 TABLE I. Assembly dimensions (see figure 1). 1/ PIN length designator Dimension “LENGTH“ .02 (0.5 mm) Dimension “M“ .005 (0.13 mm) 28 2.8 (71 mm) .530 (13.5 mm) 35 3.5 (89 mm) 1.23 (31.2

20、 mm) 38 3.8 (97 mm) 1.53 (38.9 mm) 40 4.0 (102 mm) 1.73 (43.9 mm) 48 4.8 (122 mm) 2.53 (64.3 mm) 58 5.8 (147 mm) 3.53 (89.7 mm) 64 6.4 (163 mm) 4.13 (104.9 mm) 1/ Dimensions are in inches. Millimeters, in parenthesis, are given for information only. Configuration. The configuration of a card holder

21、shall be as specified in table II. The details of a particular configuration consist of those on figures 1, 3, and 4. Card holders not requiring the options described by table II shall leave the configuration position in the PIN blank. TABLE II. Configurations. Configuration Applicable figures Hardw

22、are options - 1 No added options W 1 and 3 Lockwasher and flat washer E 1 and 4 Screw self-locking element D 1, 3, and 4 Lockwasher, flat washer and screw self-locking element Lockwasher and flat washer (see figure 3). A lockwasher and flat washer located under the screw head will provide for additi

23、onal resistance to loosening from shock and vibration. Card holders requiring a lockwasher and flat washer shall include a configuration suffix “W“ in the PIN (see classification and notes). FIGURE 3. Lockwasher and flat washer details. Provided by IHSNot for ResaleNo reproduction or networking perm

24、itted without license from IHS-,-,-AA59590/2C 5 Screw self-locking element (see figure 4). The use of a screw self-locking element will provide prevailing torque for resistance to loosening from shock and vibration. Card holders requiring a screw self-locking element shall include a configuration su

25、ffix “E“ in the PIN (see classification and notes). FIGURE 4. Screw self-locking element details. Lockwasher, flat washer, and screw self-locking element. Card holders requiring a lockwasher, flat washer, and screw self-locking element shall include a configuration suffix “D“ in the PIN (see classif

26、ication and notes). NOTES. PIN. The PIN should be used for Government purposes to buy commercial products to this CID specification sheet. See the classification section for PIN format example. Source of documents. Commercial Item Description. AA59590 Holder, Electrical Card, Wedge Retainers, 3 Piec

27、e, Screw Actuated Drive, General Requirements For. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or https:/assist.daps.dla.mil/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 191115094.) Other Publicatio

28、ns. AEROSPACE INDUSTRIES ASSOCIATION (AIA) AIA/NAS 1283 Fasteners, Male Threaded, Selflocking. (Application for copies should be addressed to the Aerospace Industries Association, 1250 Eye Street, NW, Suite 1200, Washington, DC 200053924 or at URL: http:/www.aia-aerospace.org.) Ordering data. Orderi

29、ng data is as specified in AA59590. Commercial products. As part of the market analysis and research effort, this CID specification sheet was coordinated with the following manufacturers of commercial products. At the time of CID specification sheet preparation and coordination, these manufacturers

30、were known to have commercial products that would meet the requirements of this CID specification sheet. (NOTE: This information should not be considered as a list of approved manufacturers or be used to restrict procurement to only the manufacturers shown.) Provided by IHSNot for ResaleNo reproduct

31、ion or networking permitted without license from IHS-,-,-AA59590/2C 6 Manufacturer CAGE Manufacturer name and address Manufacturer contact information 18915 Birtcher A Division of Pentair Electronic Packaging 7328 Trade Street San Diego, CA 921213410 Telephone: (858) 7402400 Toll Free: (800) 8547086

32、 Facsimile: (858) 7402430 (URL): 61081 Calmark A Division of Pentair Electronic Packaging 7328 Trade Street San Diego, CA 921213410 Telephone: (858) 7402400 Toll Free: (800) 8547086 Facsimile: (858) 7402430 Electronic mail: URL: 5BG68 Card Locks Unlimited, Inc. 2310 E. Orangethorpe Avenue Anaheim

33、, CA 928061231 Telephone: (714) 7386194 Facsimile: (714) 4460119 E-mail: URL: Part number supersession data. This CID specification sheet PINs supersedes the following manufacturers part numbers as shown in table III. The CID PINs listed in table III are only for length designator “28“. See table

34、IV for CID PIN construction using other available lengths for this specification sheet. This information is being provided to assist in reducing proliferation in the Government inventory system. TABLE III. Commercial part number supersession data. PIN designator AA59590/02 Vendor similar designator

35、or type part number 1/ CAGE 18915 Vendor similar designator or type part number 1/ CAGE 61081 Vendor similar designator or type part number 1/ CAGE 5BG68 BJ28 4550712.80B EA2252.80H 3225EBA2.80H BN28 4550712.80BA EA2252.80 3225EBA2.80 BT28 4550712.80BT EA2252.80T0 3225EBA2.80T0 BV28 4550712.80BS EA2

36、252.80T2 3225EBA2.80T2 BG28 4550712.80BM MEA2252.80TM2.5 3225EMBA2.80TM2.5 BJ28E 4550712.80BL EA2252.80HL 3225EBA2.80HL BN28E 4550712.80BAL EA2252.80L 3225EBA2.80L BT28E 4550712.80BTL EA2252.80T0L 3225EBA2.80T0L BV28E 4550712.80BSL EA2252.80T2L 3225EBA2.80T2L BG28E 4550712.80BML MEA2252.80TM2.5L 322

37、5EMBA2.80TM2.5L BJ28W 4550722.80B WEA2252.80H 3225EWBA2.80H BN28W 4550722.80BA WEA2252.80 3225EWBA2.80 BT28W 4550722.80BT WEA2252.80T0 3225EWBA2.80T0 BV28W 4550722.80BS WEA2252.80T2 3225EWBA2.80T2 BG28W 4550722.80BM MWEA2252.80TM2.5 3225EWMBA2.80TM2.5 See footnote at end of table. Provided by IHSNot

38、 for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/2C 7 TABLE III. Commercial part number supersession data Continued. PIN designator AA59590/02 Vendor similar designator or type part number 1/ CAGE 18915 Vendor similar designator or type part number 1/ CAGE 6108

39、1 Vendor similar designator or type part number 1/ CAGE 5BG68 BJ28D 4550722.80BL WEA2252.80HL 3225EWBA2.80HL BN28D 4550722.80BAL WEA2252.80L 3225EWBA2.80L BT28D 4550722.80BTL WEA2252.80T0L 3225EWBA2.80T0L BV28D 4550722.80BSL WEA2252.80T2L 3225EWBA2.80T2L BG28D 4550722.80BML MWEA2252.80TM2.5L 3225EWM

40、BA2.80TM2.5L CJ28 4550712.80 E2252.80H 3225ECG2.80H CN28 4550712.80A E2252.80 3225ECG2.80 CT28 4550712.80T E2252.80T0 3225ECG2.80T0 CV28 4550712.80S E2252.80T2 3225ECG2.80T2 CG28 4550712.80M ME2252.80TM2.5 3225EMCG2.80TM2.5 CJ28E 4550712.80L E2252.80HL 3225ECG2.80HL CN28E 4550712.80AL E2252.80L 3225

41、ECG2.80L CT28E 4550712.80TL E2252.80T0L 3225ECG2.80T0L CV28E 4550712.80SL E2252.80T2L 3225ECG2.80T2L CG28E 4550712.80ML ME2252.80TM2.5L 3225EMCG2.80TM2.5L CJ28W 4550722.80 WE2252.80H 3225EWCG2.80H CN28W 4550722.80A WE2252.80 3225EWCG2.80 CT28W 4550722.80T WE2252.80T0 3225EWCG2.80T0 CV28W 4550722.80S

42、 WE2252.80T2 3225EWCG2.80T2 CG28W 4550722.80M MWE2252.80TM2.5 3225EMWCG2.80TM2.5 CJ28D 4550722.80L WE2252.80HL 3225EWCG2.80HL CN28D 4550722.08AL WE2252.80L 3225EWCG2.80L CT28D 4550722.80TL WE2252.80T0L 3225EWCG2.80T0L CV28D 4550722.80SL WE2252.80T2L 3225EWCG2.80T2L CG28D 4550722.80ML MWE2252.80TM2.5

43、L 3225EMWCG2.80TM2.5L EJ28 4550712.80EN EEN2252.80H 3225EEN2.80H EN28 4550712.80ENA EEN2252.80 3225EEN2.80 ET28 4550712.80ENT EEN2252.80T0 3225EEN2.80T0 EV28 4550712.80ENS EEN2252.80T2 3225EEN2.80T2 EG28 4550712.80ENM MEEN2252.80TM2.5 3225EMEN2.80TM2.5 See footnote at end of table. Provided by IHSNo

44、t for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/2C 8 TABLE III. Commercial part number supersession data Continued. PIN designator AA59590/02 Vendor similar designator or type part number 1/ CAGE 18915 Vendor similar designator or type part number 1/ CAGE 610

45、81 Vendor similar designator or type part number 1/ CAGE 5BG68 EJ28E 4550712.80ENL EEN2252.80HL 3225EEN2.80HL EN28E 455071280ENAL EEN2252.80L 3225EEN2.80L ET28E 455071280ENTL EEN2252.80T0L 3225EEN2.80T0L EV28E 455071280ENSL EEN2252.80T2L 3225EEN2.80T2L EG28E 455071280ENML MEEN2252.80TM2.5L 3225EMEN2

46、.80TM2.5L EJ28W 4550722.80EN WEEN2252.80H 3225EWEN2.80H EN28W 4550722.80ENA WEEN2252.80 3225EWEN2.80 ET28W 4550722.80ENT WEEN2252.80T0 3225EWEN2.80T0 EV28W 4550722.80ENS WEEN2252.80T2 3225EWEN2.80T2 EG28W 4550722.80ENM MWEEN2252.80TM2.5 3225EWMEN2.80TM2.5 EJ28D 4550722.80ENL WEEN2252.80HL 3225EWEN2.

47、80HL EN28D 455072280ENAL WEEN2252.80L 3225EWEN2.80L ET28D 455072280ENTL WEEN2252.80T0L 3225EWEN2.80T0L EV28D 455072280ENSL WEEN2252.80T2L 3225EWEN2.80T2L EG28D 455072280ENML MWEEN2252.80TM2.5L 3225EWMEN2.80TM2.5L HJ28 4550712.80B3 EHA2252.80H 3225EBH2.80H HN28 4550712.80B3A EHA2252.80 3225EBH2.80 HT28 4550712.80B3T EHA2252.80T0 3225EBH2.80T0 HV28 4550712.80B3S EHA2252.80T2 3225EBH2.80T2 HG28 4550712.80B3M MEHA2252.80TM2.5 3225