DLA A-A-59590 20 B-2012 HOLDER ELECTRICAL CARD WEDGE RETAINERS 3 PIECE SCREW ACTUATED DRIVE 260 X 260 INCH BODY SIZE WITH VISUAL LOCK INDICATION AND SCREW RETENTION.pdf

1、INCHPOUND AA59590/20B 20 May 2012 SUPERSEDING AA59590/20A 7 July 2007 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET HOLDER, ELECTRICAL CARD, WEDGE RETAINERS, 3 PIECE, SCREW ACTUATED DRIVE .260 X .260 INCH BODY SIZE, WITH VISUAL LOCK INDICATION AND SCREW RETENTION The General Services Administratio

2、n has authorized the use of this commercial item description for all federal agencies. The complete requirements for procuring electrical card holders described herein shall consist of this document and the latest issue in effect of AA59590. CLASSIFICATION/PART IDENTIFICATION NUMBER (PIN). This comm

3、ercial item description (CID) specification sheet uses a classification system which is included in the Part Identification Number (PIN) as shown in the following example (see notes herein). AA59590 CID number /20 Applicable CID specification sheet * Finish * Mounting * * Length (see table I) * Conf

4、iguration Example: AA59590/20ET58E is the PIN for a nickel plated, 5.8 inches (147 mm) long card holder with a visual lock indication and a screw self-locking element. The card holder also features two tapped 0-80 UNF mounting holes for use with fasteners. SALIENT CHARACTERISTICS. Performance. Card

5、holders shall hold the circuit card assembly firmly in its installed position and provide high resistance to loosening due to shock and vibration. Card holders shall also provide maximum thermal transfer from the circuit card assembly to the cold plate or heat sink surfaces. The screw retention feat

6、ure is intended to prevent unintentional disassembly of the card holder. Interface and physical dimensions. The card holders supplied to this CID specification sheet shall be as specified herein (see figures 1, 2, 3, 4, 5 and table I) and meet the general requirements of CID AA59590. Material. Unles

7、s otherwise specified herein, the card holder materials shall be as specified in AA59590. Actuating screw hex drive socket. The dimension for hex drive socket shall be .094 inch (2.39 mm) for mounting options “J“, “N“, “T“ and “V“. The dimension for hex drive socket shall be a metric dimension of 2.

8、5 mm (.098 inch) across flats for mounting option “G“. Cold plate dimensions. Recommend cold plate slot width to accommodate the circuit card assembly with attached card holder is .300 inch (7.62 mm) plus the thickness of the printed board of the circuit card assembly (see AA59590). AMSC N/A FSC 599

9、8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/20B 2 Inches mm Inches mm Inches mm Inches mm Inches mm .20 .25 5.1 6.4 .260 .270 6.60 6.86 .27 .30 6.9 7.62 .325 .39 8.26 9.9 .56 .70 14.2 17.8 NOTES: 1. Dimensions are in inches. Millimeters

10、 are given for general information only. 2. Unless otherwise specified, tolerances are .02 inch (0.51 mm) for two place decimals and .010 inch (0.25 mm) for three place decimals. 3. The tolerance for the mounting hole spacing is .005 inches (0.13 mm). 4. The across flats dimension for hex drive sock

11、et shall be .094 inch (2.39 mm) for mounting options “J“, “N“, “T“, and “V“. The across flats dimension for hex drive socket shall be a metric dimension of 2.5 mm (.098 inch) across flats for mounting option “G“. FIGURE 1. Relaxed and expanded dimensions, basic configuration. Provided by IHSNot for

12、ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/20B 3 Nominal installation torque. When card holders are used in cold plate applications, the nominal installation torque of each card holder shall be as follows: 10 inch-pounds (1.1 N-m) for assemblies using no optio

13、ns or option “W“ and 12 inch-pounds (1.4 N-m) for assemblies using options “D“ or “E“. Screw retention locknut (see figure 2). Card holders shall have a screw retention locknut intended to prevent unintentional disassembly of the card holder. The locknut shall be fabricated of a corrosion resistant

14、material. FIGURE 2. Screw retaining self-locking nut details. Visual lock indicator (see figure 3). Card holders shall have a visual indicator to show when the card holder assembly is in its relaxed (unlocked) state. When the card holder assembly is in the relaxed state, the end of the actuating scr

15、ew shall display a red band on the side of the screw. When the actuating screw on the card holder has been tightened so that the assembly is in the expanded (locked) position, this red band shall be concealed. FIGURE 3. Visual lock indicator details. Finish. The finish designator shall be as specifi

16、ed in AA59590. The wedge body finishes available for this CID specification sheet are as follows: “B“ (black anodize), “C“ (gold chemical film), “E“ (electroless nickel), “H“ (hard black anodize), or “R“ (clear chemical film). Mounting. The mounting designators shall be as specified in AA59590. Exce

17、pt when using mounting option “N“, two mounting holes are required on the card holders. The mounting options available for this CID specification sheet are as follows: “J“ (rivet mounting holes), “N“ (no mounting holes), “T“ (tapped 0-80 UNF 2B holes), “V“ (tapped 2-56 UNC 2B holes), or “G“ (tapped

18、M2.5 x.45 metric holes). See figure 1 and table I for mounting hole spacing requirements. Card holders using mounting option “J“ may be shipped unassembled. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/20B 4 Counterbore holes (for rivet mo

19、unting). The holes used for rivet mounting shall be .068/.073 inch (1.73/1.85 mm) diameter, countersunk 100 degrees by .140 inch (3.56 mm) diameter through holes with an access/clearance counterbore of .156 inch (3.96 mm) diameter by .200 inch (5.08 mm) deep. Rivets. This card holder uses rivet type

20、 A as specified in AA59590 when rivet mounting is used. Length, expanded, and relaxed dimensions. The length designator shall be as specified in AA59590 and the lengths available for this CID specification sheet are listed in table I. The length, expanded, and relaxed dimensions shall be as specifie

21、d on figure 1. TABLE I. Assembly dimensions (see figure 1). 1/ PIN length designator Dimension “LENGTH“ .02 (0.5 mm) Dimension “B“ .03 (0.8 mm) Dimension “M“ .005 (0.13 mm) 28 2.8 (71 mm) 2.30 (58.4 mm) .90 (22.9 mm) 33 3.3 (84 mm) 2.80 (71.1 mm) 1.40 (35.6 mm) 38 3.8 (97 mm) 3.30 (83.8 mm) 1.90 (48

22、.3 mm) 43 4.3 (109 mm) 3.80 (96.5 mm) 2.40 (61.0 mm) 48 4.8 (122 mm) 4.30 (109.2 mm) 2.90 (73.7 mm) 53 5.3 (135 mm) 4.80 (121.9 mm) 3.40 (86.4 mm) 58 5.8 (147 mm) 5.30 (134.6 mm) 3.90 (99.1 mm) 1/ Dimensions are in inches. Millimeters, in parenthesis, are given for general information only. Configur

23、ation. The configuration of a card holder shall be as specified in table II. The details of a particular configuration consist of those on figures 1, 2, and 3, and may include those on figures 4 and 5. The correct PIN configuration identifier for each option is listed in table II. Card holders not r

24、equiring the options described by table II shall leave the configuration position in the PIN blank. TABLE II. Configuration. Configuration Applicable figures Hardware options 1, 2 and 3 No changes from basic configuration W 1, 2, 3 and 4 Lockwasher and flat washer E 1, 2, 3 and 5 Screw self-locking

25、element D 1, 2, 3, 4 and 5 Lockwasher, flat washer, and screw self-locking element Lockwasher and flat washer (see figure 4). The use of a lockwasher and flat washer located under the screw head will provide for additional resistance to loosening of the card holder assembly from shock and vibration.

26、 Card holders requiring a lockwasher and flat washer shall include a suffix “W“ in the PIN (see classification and notes). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/20B 5 FIGURE 4. Lockwasher and flat washer details. Screw self-locking

27、element (see figure 5). The use of a self-locking element on the screw will provide a prevailing-torque for increased resistance to loosening of the card holder assembly from shock and vibration. Card holders requiring a screw self-locking element shall include a suffix “E“ in the PIN (see classific

28、ation and notes). FIGURE 5. Screw self-locking element details. Lockwasher, flat washer, and screw self-locking element. Card holders requiring a lockwasher, flat washer, and screw self-locking element option shall include a suffix “D“ in the PIN (see classification and notes). NOTES. PIN. The PIN s

29、hould be used for Government purposes to buy commercial products to this CID specification sheet. See the classification section for PIN format example. Source of documents. Commercial Item Description. AA59590 Holder, Electrical Card, Wedge Retainers, 3 Piece, Screw Actuated Drive, General Requirem

30、ents For. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or https:/assist.daps.dla.mil/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 191115094.) Ordering data. Ordering data shall be as specified in AA5

31、9590. Commercial products. As part of the market analysis and research effort, this CID specification sheet was coordinated with the following manufacturers of commercial products. At the time of CID specification sheet preparation and coordination, these manufacturers were known to have commercial

32、products that would meet the requirements of this CID specification sheet. (NOTE: This information should not be considered as a list of approved manufacturers or be used to restrict procurement to only the manufacturers shown.) Provided by IHSNot for ResaleNo reproduction or networking permitted wi

33、thout license from IHS-,-,-AA59590/20B 6 Manufacturer CAGE Manufacturer name and address Manufacturer contact information 61081 Calmark A Division of Pentair Technical Products 7328 Trade Street San Diego, CA 921213410 Telephone: (858) 7402400 Toll Free: (800) 8547086 Facsimile: (858) 7402430 E-mail

34、: URL: 5BG68 Card Locks Unlimited, Inc. 2310 E. Orangethorpe Avenue Anaheim, CA 928061231 Telephone: (714) 7386194 Facsimile: (714) 4460119 E-mail: URL: Part number supersession data. These CID specification sheet PINs supersedes the following manufacturers part numbers as shown in table III. Th

35、e CID PINs listed in table III are only for length designator “28“. See table IV for CID PIN construction using other available lengths for this specification sheet. This information is being provided to assist in reducing proliferation in the Government inventory system. TABLE III. Commercial part

36、number supersession data. PIN designator AA59590/20 Vendor similar designator or type part number 1/ 2/ CAGE 61081 CAGE 5BG68 BJ28 VA245CR2.80HR 3245VBA2.80HR BN28 VA245CR2.80R 3245VBA2.80R BT28 VA245CR2.80T0R 3245VBA2.80T0R BV28 VA245CR2.80T2R 3245VBA2.80T2R BG28 MVA245CR2.80TM2.5R 3245MVBA2.80TM2.

37、5R BJ28W WVA245CR2.80HR 3245VWBA2.80HR BN28W WVA245CR2.80R 3245VWBA2.80R BT28W WVA245CR2.80T0R 3245VWBA2.80T0R BV28W WVA245CR2.80T2R 3245VWBA2.80T2R BG28W MWVA245CR2.80TM2.5R 3245MVWBA2.80TM2.5R BJ28E VA245CR2.80HLR 3245VBA2.80HLR BN28E VA245CR2.80LR 3245VBA2.80LR BT28E VA245CR2.80T0LR 3245VBA2.80T0

38、LR BV28E VA245CR2.80T2LR 3245VBA2.80T2LR BG28E MVA245CR2.80TM2.5LR 3245MVBA2.80TM2.5LR BJ28D WVA245CR2.80HLR 3245VWBA2.80HLR BN28D WVA245CR2.80LR 3245VWBA2.80LR BT28D WVA245CR2.80T0LR 3245VWBA2.80T0LR BV28D WVA245CR2.80T2LR 3245VWBA2.80T2LR BG28D MWVA245CR2.80TM2.5LR 3245MVWBA2.80TM2.5LR See footnot

39、es at end of table.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/20B 7 TABLE III. Commercial part number supersession data Continued. PIN designator AA59590/20 Vendor similar designator or type part number 1/ 2/ CAGE 61081 CAGE 5BG68 CJ28 V

40、245CR2.80HR 3245VCG2.80HR CN28 V245CR2.80R 3245VCG2.80R CT28 V245CR2.80T0R 3245VCG2.80T0R CV28 V245CR2.80T2R 3245VCG2.80T2R CG28 MV245CR2.80TM2.5R 3245MVCG2.80TM2.5R CJ28W WV245CR2.80HR 3245VWCG2.80HR CN28W WV245CR2.80R 3245VWCG2.80R CT28W WV245CR2.80T0R 3245VWCG2.80T0R CV28W WV245CR2.80T2R 3245VWCG

41、2.80T2R CG28W MWV245CR2.80TM2.5R 3245MVWCG2.80TM2.5R CJ28E V245CR2.80HLR 3245VCG2.80HLR CN28E V245CR2.80LR 3245VCG2.80LR CT28E V245CR2.80T0LR 3245VCG2.80T0LR CV28E V245CR2.80T2LR 3245VCG2.80T2LR CG28E MV245CR2.80TM2.5LR 3245MVCG2.80TM2.5LR CJ28D WV245CR2.80HLR 3245VWCG2.80HLR CN28D WV245CR2.80LR 324

42、5VWCG2.80LR CT28D WV245CR2.80T0LR 3245VWCG2.80T0LR CV28D WV245CR2.80T2LR 3245VWCG2.80T2LR CG28D MWV245CR2.80TM2.5LR 3245MVWCG2.80TM2.5LR EJ28 VEN245CR2.80HR 3245VEN2.80HR EN28 VEN245CR2.80R 3245VEN2.80R ET28 VEN245CR2.80T0R 3245VEN2.80T0R EV28 VEN245CR2.80T2R 3245VEN2.80T2R EG28 MVEN245CR2.80TM2.5LR

43、 3245MVEN2.80TM2.5R EJ28W WVEN245CR2.80HR 3245VWEN2.80HR EN28W WVEN245CR2.80R 3245VWEN2.80R ET28W WVEN245CR2.80T0R 3245VWEN2.80T0R EV28W WVEN245CR2.80T2R 3245VWEN2.80T2R EG28W MWVEN245CR2.80TM2.5R 3245MVWEN2.80TM2.5R See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or netw

44、orking permitted without license from IHS-,-,-AA59590/20B 8 TABLE III. Commercial part number supersession data Continued. PIN designator AA59590/20 Vendor similar designator or type part number 1/ 2/ CAGE 61081 CAGE 5BG68 EJ28E VEN245CR2.80HLR 3245VEN2.80HLR EN28E VEN245CR2.80LR 3245VEN2.80LR ET28E

45、 VEN245CR2.80T0LR 3245VEN2.80T0LR EV28E VEN245CR2.80T2LR 3245VEN2.80T2LR EG28E MVEN245CR2.80TM2.5LR 3245MVEN2.80TM2.5LR EJ28D WVEN245CR2.80HLR 3245VWEN2.80HLR EN28D WVEN245CR2.80LR 3245VWEN2.80LR ET28D WVEN245CR2.80T0LR 3245VWEN2.80T0LR EV28D WVEN245CR2.80T2LR 3245VWEN2.80T2LR EG28D MWVEN245CR2.80TM

46、2.5LR 3245MVWEN2.80TM2.5LR HJ28 VHA245CR2.80HR 3245VBH2.80HR HN28 VHA245CR2.80R 3245VBH2.80R HT28 VHA245CR2.80T0R 3245VBH2.80T0R HV28 VHA245CR2.80T2R 3245VBH2.80T2R HG28 MVHA245CR2.80TM2.5LR 3245MVBH2.80TM2.5R HJ28W WVHA245CR2.80HR 3245VWBH2.80HR HN28W WVHA245CR2.80R 3245VWBH2.80R HT28W WVHA245CR2.8

47、0T0R 3245VWBH2.80T0R HV28W WVHA245CR2.80T2R 3245VWBH2.80T2R HG28W MWVHA245CR2.80TM2.5LR 3245MVWBH2.80TM2.5R HJ28E VHA245CR2.80HLR 3245VBH2.80HLR HN28E VHA245CR2.80LR 3245VBH2.80LR HT28E VHA245CR2.80T0LR 3245VBH2.80T0LR HV28E VHA245CR2.80T2LR 3245VBH2.80T2LR HG28E VMHA245CR2.80TM2.5LR 3245MVBH2.80TM2

48、.5R HJ28D WVHA245CR2.80HLR 3245VWBH2.80HLR HN28D WVHA245CR2.80LR 3245VWBH2.80LR HT28D WVHA245CR2.80T0LR 3245VWBH2.80T0LR HV28D WVHA245CR2.80T2LR 3245VWBH2.80T2LR HG28D MWVHA245CR2.80TM2.5LR 3245MVWBH2.80TM2.5LR See footnotes at end of table.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/20B 9 TABLE III.