DLA A-A-59590 4 D-2013 HOLDER ELECTRICAL CARD WEDGE RETAINERS 3 PIECE SCREW ACTUATED DRIVE 225 X 260 INCH BODY SIZE.pdf

1、INCHPOUND AA59590/4D 4 May 2013 SUPERSEDING AA59590/4C 4 October 2010 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET HOLDER, ELECTRICAL CARD, WEDGE RETAINERS, 3 PIECE, SCREW ACTUATED DRIVE, .225 X .260 INCH BODY SIZE The General Services Administration has authorized the use of this commercial item

2、 description for all federal agencies. The complete requirements for procuring electrical card holders described herein shall consist of this document and the latest issue in effect of AA59590. CLASSIFICATION/PART OR IDENTIFICATION NUMBER (PIN). This commercial item description (CID) specification s

3、heet uses a classification system which is included in the Part Identification Number (PIN) as shown in the following example (see notes). AA59590 CID number /04 Applicable CID specification sheet * Finish * Mounting * * Length (see table I) W, D, E Configuration (see table II) Example: AA59590/04EV

4、28W is the PIN for a nickel finished, 2.8 inch (71.1 mm) long card holder. The card holder also features two tapped mounting holes for use with 256 UNC 2B fasteners and a lockwasher and flat washer under the screw head for added resistance to loosening. SALIENT CHARACTERISTICS. Performance. Card hol

5、ders shall hold the circuit card assembly firmly in its installed position. When the card holder is installed properly, it is capable of withstanding 60g/6ms of shock, 25 Grms of vibration, and provides from 2 to 4 degrees C/W/inch thermal resistance transfer between the circuit card assembly and th

6、e heat sink surfaces. Material. Unless otherwise specified herein, the card holder materials shall be as specified in AA59590. Interface and physical dimensions. The card holders supplied to this CID specification sheet shall be as specified on figures 1, 2, 3, in table I, and AA59590. Actuating scr

7、ew hex drive socket. The across flats dimension for the hex drive socket shall be as follows: .094 inch (2.38 mm) for mounting options “J“, “K“, “N“, “T“, “R“, “V“, and “S“ and 2.5 mm (0.098 inch) for mounting options “G“ and “M“. Cold plate slot width dimensions. The recommend cold plate slot width

8、 to accommodate the circuit card assembly with attached card holder is .300 inch (7.62 mm) plus the thickness of the printed board of the circuit card assembly (see AA59590). Nominal installation torque. When card holders are used in cold plate applications, the nominal installation torque of each c

9、ard holder shall be as follows: 6 inch-pounds (0.68 N-m) for assemblies using no options or option “W“ and 7.2 inch-pounds (0.81 N-m) for assemblies using options “E“ or “D“. AMSC N/A FSC 5998 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/4

10、D 2 Inches mm Inches mm Inches mm Inches mm .070 .12 1.8 3.1 .20 .225 5.1 5.7 .250 .270 6.4 6.9 .325 .70 8.3 17.8 NOTES: 1. Dimensions are in inches. Millimeters are given for general information only. 2. Unless otherwise specified, tolerances are .02 inch (0.5 mm) for two place decimals and .010 in

11、ch (0.25 mm) for three place decimals. 3. Dimension shall be .20 inch (5.1 mm) maximum on card holders without option “W“ or “D“ and .30 inch (7.6 mm) maximum on card holders with option “W“ or “D“. 4. The across flats dimension for hex drive socket shall be .094 inch (2.38 mm) for mounting options

12、“J“, “K“, “N“, “T“, “R“, “V“, and “S“. The across flats dimension for hex drive socket shall be a metric dimension of 2.5 mm (.098 inch) across flats for mounting options “G“ and “M“. FIGURE 1. Relaxed and expanded dimensions. Provided by IHSNot for ResaleNo reproduction or networking permitted with

13、out license from IHS-,-,-AA59590/4D 3 TABLE I. Additional assembly dimensions (see figure 1). 1/ PIN length designator Dimension “LENGTH“ .02 (0.5) Dimension “A“ (maximum) Dimension “B“ .03 (0.8) Dimension “C“ .005 (0.13) Without options “W“ or “D“ With options “W“ or “D“ 18 1.8 (45.7) 2.00 (50.8) 2

14、.10 (53.3) 1.30 (33.0) .75 (19.1) 23 2.3 (58.4) 2.50 (63.5) 2.60 (66.0) 1.80 (45.7) .40 (10.2) 28 2.8 (71.1) 3.00 (76.2) 3.10 (78.7) 2.30 (58.4) .90 (22.9) 30 3.0 (76.2) 3.20 (81.3) 3.30 (83.8) 2.50 (63.5) 1.10 (27.9) 33 3.3 (83.8) 3.50 (88.9) 3.60 (91.4) 2.80 (71.1) 1.40 (35.6) 35 3.5 (88.9) 3.70 (

15、94.0) 3.80 (96.5) 3.00 (76.2) 1.60 (40.6) 38 3.8 (96.5) 4.00 (101.6) 4.10 (104.1) 3.30 (83.8) 1.90 (48.3) 43 4.3 (109.2) 4.50 (114.3) 4.60 (116.8) 3.80 (96.5) 2.40 (61.0) 48 4.8 (121.9) 5.00 (127.0) 5.10 (129.1) 4.30 (109.2) 2.90 (73.7) 53 5.3 (134.6) 5.50 (139.7) 5.60 (142.2) 4.80 (121.9) 3.40 (86.

16、4) 55 5.5 (139.7) 5.70 (144.8) 5.80 (147.3) 5.00 (127.0) 3.60 (91.4) 58 5.8 (147.3) 6.00 (152.4) 6.10 (154.9) 5.30 (134.6) 3.90 (99.1) 61 6.1 (154.9) 6.30 (160.0) 6.40 (162.6) 5.60 (142.2) 4.20 (106.7) 63 6.3 (160.0) 6.50 (165.1) 6.60 (167.6) 5.80 (147.3) 4.40 (111.8) 67 6.7 (170.2) 6.90 (175.3) 7.0

17、0 (177.8) 6.20 (157.5) 4.80 (121.9) 1/ Dimensions are in inches. Millimeters, in parenthesis, are given for general information only. Finish. The finish designator shall be as specified in AA59590. The wedge body finishes available for this CID specification sheet are as follows: “B“ (black anodize)

18、, “C“ (gold chemical film), “E“ (electroless nickel), “H“ (hard black anodize), and “R“ (clear chemical film). Mounting options. The mounting designators shall be as specified in AA59590. The mounting options available for this CID specification sheet are as follows: “J“ or “K“ (rivet mounting holes

19、), “N“ (no mounting holes), “R“ or “T“ (tapped 080 UNF 2B holes), “V“ or “S“ (tapped 256 UNC 2B holes), or “G“ or “M“ (tapped M2.5 x.45 metric holes). Card holders using mounting option “J“ may be shipped unassembled. See figure 1 and table I for mounting hole spacing requirements. Mounting holes (w

20、hen required). Two mounting holes are required on card holders less than 5.30 inches (134.6 mm) in length. Three mounting holes are required on card holders 5.30 inches (134.6 mm) or greater in length. The third mounting hole shall be centered on the mounting body. See figure 1 and table I for mount

21、ing hole locations and spacing requirements. Rivet mounting holes. The holes used for rivet mounting shall be .066 to .073 inch (1.68 to 1.85 mm) diameter through holes, countersunk 100 degrees by .140 inch (3.56 mm) diameter with an access/clearance counterbore hole of .156 inch (3.96 mm) diameter

22、by .200 inch (5.08 mm) deep. Rivets. This card holder uses rivet style A as specified in AA59590 when rivet mounting is used. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/4D 4 Length, expanded, and relaxed dimensions. The length, expanded,

23、 and relaxed dimensions shall be as specified on figure 1. The length designator shall be as specified in AA59590 and the available lengths for this specification sheet are listed in figure 1. Configuration. The configuration of a card holder shall be as specified in table II. The details of a parti

24、cular configuration consist of those on figures 1, 2, and 3. Card holders not requiring the options described by table II shall leave the configuration position in the PIN blank. TABLE II. Configurations. Configuration Applicable figures Hardware options 1 No added options W 1 and 2 Lockwasher and f

25、lat washer E 1 and 3 Screw self-locking element D 1, 2, and 3 Lockwasher, flat washer and screw self-locking element Lockwasher and flat washer (see figure 2). The use of a lockwasher and flat washer located under the screw head will provide for additional resistance to loosening of the card holder

26、assembly from shock and vibration. Card holders requiring a lockwasher and flat washer shall include a configuration suffix “W“ in the PIN (see classification and notes). FIGURE 2. Lockwasher and flat washer details. Screw self-locking element (see figure 3). The use of a screw self-locking element

27、on the screw will provide prevailing torque for increased resistance to loosening of the card holder assembly from shock and vibration. The screw self-locking element shall be as specified in AA59590. Card holders requiring a screw self-locking element shall include a configuration suffix “E“ in the

28、 PIN (see classification and notes). FIGURE 3. Screw self-locking element details. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/4D 5 Lockwasher, flat washer, and screw self-locking element. Card holders requiring a lockwasher, flat washer,

29、 and screw self-locking element shall include a configuration suffix “D“ in the PIN (see classification and notes). NOTES. PIN. The PIN should be used for Government purposes to buy commercial products to this CID specification sheet. See the classification section for PIN format example. Source of

30、documents. Commercial Item Description AA59590 Holder, Electrical Card, Wedge Retainers, 3 Piece, Screw Actuated Drive, General Requirements For. (Copies of these documents are available online at http:/quicksearch.dla.mil or https:/assist.dla.mil or from the Standardization Document Order Desk, 700

31、 Robbins Avenue, Building 4D, Philadelphia, PA 191115094.) Ordering data. Ordering data shall be as specified in AA59590. Commercial products. As part of the market analysis and research effort, this CID specification sheet was coordinated with the following manufacturers of commercial products. At

32、the time of CID specification sheet preparation and coordination, these manufacturers were known to have commercial products that would meet the requirements of this CID specification sheet. (NOTE: This information should not be considered as a list of approved manufacturers or be used to restrict p

33、rocurement to only the manufacturers shown.) Manufacturer CAGE Manufacturer name and address Manufacturer contact information 18915 Birtcher A Division of Pentair Electronic Packaging 7328 Trade Street San Diego, CA 921213410 Telephone: (858) 7402400 Toll Free: (800) 8547086 Facsimile: (858) 6794555

34、 (URL): 61081 Calmark A Division of Pentair Electronic Packaging 7328 Trade Street San Diego, CA 921213410 Telephone: (858) 7402400 Toll Free: (800) 8547086 Facsimile: (858) 7402430 Electronic mail: URL: 5BG68 American Circuit Card Retainers, Inc. 2310 E. Orangethorpe Avenue Anaheim, CA 928061231

35、 Telephone: (714) 7386194 Facsimile: (714) 4460119 E-mail: URL: http:/ 3E7U8 Wakefield Solutions 200 Towerview Court Cary, NC 27513 Telephone: (919) 4692004 Facsimile: (919) 4692827 E-mail: URL: Part number supersession data. These CID specification sheet part numbers supersede the following manu

36、facturers part numbers in table III and on DESC Drawing 84103 (table IV) as shown. The CID PINs listed in table III are only for length designator “28“. See table V for CID PIN construction using other available lengths for this specification sheet. This information is being provided to assist in re

37、ducing proliferation in the Government inventory system. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/4D 6 TABLE III. Commercial part number supersession data. PIN designator AA59590/04 Vendor similar designator or type part number 1/ 2/ C

38、AGE 18915 CAGE 61081 CAGE 5BG68 CAGE 3E7UB BJ28 406B A225CR2.80H 3225BA2.80H 426B280RSB BN28 406BA A225CR2.80 3225BA2.80 426B280ASB BT28 406BT A225CR2.80T0 3225BA2.80T0 426B280TSB BV28 406BS A225CR2.80T2 3225BA2.80T2 426B280SSB BG28 406BM MA225CR2.80TM2.5 3225MBA2.80TM2.5 426B280MMB BJ28E 406BL A225

39、CR2.80HL 3225BA2.80HL 426B280RSBP BN28E 406BAL A225CR2.80L 3225BA2.80L 426B280ASBP BT28E 406BTL A225CR2.80T0L 3225BA2.80T0L 426B280TSBP BV28E 406BSL A225CR2.80T2L 3225BA2.80T2L 426B280SSBP BG28E 406BML MA225CR2.80TM2.5L 3225MBA2.80TM2.5L 426B280MMBP BJ28W 406BLF WA225CR2.80H 3225WBA2.80H 426B280RSBW

40、 BN28W 406BLFA WA225CR2.80 3225WBA2.80 426B280ASBW BT28W 406BLFT WA225CR2.80T0 3225WBA2.80T0 426B280TSBW BV28W 406BLFS WA225CR2.80T2 3225WBA2.80T2 426B280SSBW BG28W 406BLFM MWA225CR2.80TM2.5 3225MWBA2.80TM2.5 426B280MMBW BJ28D 406BLFL WA225CR2.80HL 3225WBA2.80HL 426B280RSBWP BN28D 406BLFAL WA225CR2.

41、80L 3225WBA2.80L 426B280ASBWP BT28D 406BLFTL WA225CR2.80T0L 3225WBA2.80T0L 426B280TSBWP BV28D 406BLFSL WA225CR2.80T2L 3225WBA2.80T2L 426B280SSBWP BG28D 406BLFML MWA225CR2.80TM2.5L 3225MWBA2.80TM2.5L 426B280MMBWP CJ28 406 225CR2.80H 3225CG2.80H 426B280RSG CN28 406A 225CR2.80 3225CG2.80 426B280ASG CT2

42、8 406T 225CR2.80T0 3225CG2.80T0 426B280TSG CV28 406S 225CR2.80T2 3225CG2.80T2 426B280SSG CG28 406M M225CR2.80TM2.5 3225MCG2.80TM2.5 426B280MMG CJ28E 406L 225CR2.80HL 3225CG2.80HL 426B280RSGP CN28E 406AL 225CR2.80L 3225CG2.80L 426B280ASGP CT28E 406TL 225CR2.80T0L 3225CG2.80T0L 426B280TSGP CV28E 406SL

43、 225CR2.80T2L 3225CG2.80T2L 426B280SSGP CG28E 406ML M225CR2.80TM2.5L 3225MCG2.80TM2.5L 426B280MMGP See footnote at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/4D 7 TABLE III. Commercial part number supersession data Continue

44、d. PIN designator AA59590/04 Vendor similar designator or type part number 1/ 2/ CAGE 18915 CAGE 61081 CAGE 5BG68 CAGE 3E7UB CJ28W 406LF W225CR2.80H 3225WCG2.80H 426B280RSGW CN28W 406LFA W225CR2.80 3225WCG2.80 426B280ASGW CT28W 406LFT W225CR2.80T0 3225WCG2.80T0 426B280TSGW CV28W 406LFS W225CR2.80T2

45、3225WCG2.80T2 426B280SSGW CG28W 406LFM MW225CR2.80TM2.5 3225MWCG2.80TM2.5 426B280MMGW CJ28D 406LFL W225CR2.80HL 3225WCG2.80HL 426B280RSGWP CN28D 406LFAL W225CR2.80L 3225WCG2.80L 426B280ASGWP CT28D 406LFTL W225CR2.80T0L 3225WCG2.80T0L 426B280TSGWP CV28D 406LFSL W225CR2.80T2L 3225WCG2.80T2L 426B280SSG

46、WP CG28D 406LFML MW225CR2.80TM2.5L 3225MWCG2.80TM2.5L 426B280MMGWP EJ28 406EN EN225CR2.80H 3225EN2.80H 426B280RSE EN28 406ENA EN225CR2.80 3225EN2.80 426B280ASE ET28 406ENT EN225CR2.80T0 3225EN2.80T0 426B280TSE EV28 406ENS EN225CR2.80T2 3225EN2.80T2 426B280SSE EG28 406ENM MEN225CR2.80TM2.5 3225MEN2.8

47、0TM2.5 426B280MME EJ28E 406ENL EN225CR2.80HL 3225EN2.80HL 426B280RSEP EN28E 406ENAL EN225CR2.80L 3225EN2.80L 426B280ASEP ET28E 406ENTL EN225CR2.80T0L 3225EN2.80T0L 426B280TSEP EV28E 406ENSL HEN25CR2.80T2L 3225EN2.80T2L 426B280SSEP EG28E 406ENML MEN225CR2.80TM2.5L 3225MEN2.80TM2.5L 426B280MMEP EJ28W 406ENLF WEN225CR2.80H 3225WEN2.80H 426B280RSEW EN28W 406ENLFA WEN225CR2.80 3225WEN2.80 426B280ASEW ET28W 406