DLA A-A-59590 7 C-2013 HOLDER ELECTRICAL CARD WEDGE RETAINERS 3 PIECE SCREW ACTUATED DRIVE 220 X 220 INCH BODY SIZE.pdf

1、INCHPOUND AA59590/7C 7 August 2013 SUPERSEDING AA59590/7B 22 April 2010 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET HOLDER, ELECTRICAL CARD, WEDGE RETAINERS, 3 PIECE, SCREW ACTUATED DRIVE, .220 X .220 INCH BODY SIZE The General Services Administration has authorized the use of this commercial it

2、em description for all federal agencies. The complete requirements for procuring electrical card holders described herein shall consist of this document and the issue in effect of AA59590. CLASSIFICATION/PART IDENTIFICATION NUMBER (PIN). This commercial item description (CID) specification sheet use

3、s a classification system which is included in the Part Identification Number (PIN) as shown in the following example (see notes). AA59590 CID number /07 Applicable CID specification sheet B, C, H, R Finish * Mounting * * Length (see table I) W, D, E Configuration Example: AA59590/07HJ48D is the PIN

4、 for a hard black anodize finished, 4.8 inch (121.9 mm) long card holder. The card holder also features two counterbored through holes for rivet mounting, and a combination of a lockwasher, flat washer, and screw self-lock element for added resistance to loosening. SALIENT CHARACTERISTICS. Performan

5、ce. Card holders shall hold the circuit card assembly it is attached to firmly in its installed position and prevent loosening or movement as a result of shock and vibration. When the card holder is installed properly, it is capable of withstanding 60g/6ms of shock, 25 G-rms of vibration, and provid

6、es from 2 to 4 degrees C/W/inch thermal resistance transfer between the circuit card assembly and the heat sink surfaces. Interface and physical dimensions. The card holders supplied to this CID specification sheet shall be as specified on figures 1, 2, 3, in table I, and AA59590. Actuating screw he

7、x drive socket. The across flats dimension for the hex drive socket shall be as follows: .094 inch (2.38 mm) for mounting options “J“, “K“, “N“, “T“, “R“, “V“, and “S“ and .098 inch (2.5 mm) for mounting options “G“ and “M“. Material. Unless otherwise specified herein, the card holder materials shal

8、l be as specified in AA59590. Nominal installation torque. When card holders are used in cold plate applications, the nominal installation torque of each card holder shall be as follows: 6 inch-pounds (0.68 N-m) for assemblies using no options or option “W“ and 8 inch-pounds (0.90 N-m) for assemblie

9、s using options “E“ or “D“. AMSC N/A FSC 5998 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/7C 2 Inches mm Inches mm Inches mm .070 .20 1.78 5.1 .225 .275 5.72 6.99 .28 .67 7.1 17.0 NOTES: 1. Dimensions are in inches. Millimeters are given

10、for general information only. 2. Unless otherwise specified, tolerances are .02 inch (0.51 mm) for two place decimals and .010 inch (0.25 mm) for three place decimals. 3. The across flats dimension for hex drive socket shall be .094 inch (2.38 mm) for mounting options “J“, “K“, “N“, “T“, “R“, “V“, a

11、nd “S“. The across flats dimension for hex drive socket shall be a metric dimension of .098 inch (2.5 mm) across flats for mounting options “G“ and “M“. FIGURE 1. Relaxed and expanded dimensions. Cold plate slot width dimensions (when applicable). The recommend cold plate slot width to accommodate t

12、he circuit card assembly with attached card holder is .250 inch (6.35 mm) plus the thickness of the printed board of the circuit card assembly (see AA59590). Finish. The finish designator shall be as specified in AA59590. The wedge body finishes available for this CID specification sheet are as foll

13、ows: “B“ (black anodize), “C“ (gold chemical film), “H“ (hard black anodize), or “R“ (clear chemical film). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/7C 3 Mounting. The mounting designators shall be as specified in AA59590. The mounting

14、 options available for this CID specification sheet are as follows: “J“ or “K“ (rivet mounting holes), “N“ (no mounting holes), “T“ or “R“ (tapped 0-80 UNF 2B holes), “V“ or “S“ (tapped 2-56 UNC 2B holes), or “G“ or “M“ (tapped M2.5 x.45 metric holes). Card holders using mounting option “J“ may be s

15、hipped unassembled. See figure 1 for mounting hole spacing requirements. Mounting holes and locations (when required). Two mounting holes are required on card holders less than 5.30 inches (134.6 mm) in length. Three mounting holes are required on card holders 5.30 inches (134.6 mm) or greater in le

16、ngth. The third mounting hole shall be centered on the mounting body. See figure 1 and table I for mounting hole locations and spacing requirements. Rivet mounting holes. The holes used for rivet mounting shall be .066 to .073 inch (1.68 to 1.85 mm) diameter through holes, countersunk 100 degrees by

17、 .140 inch (3.56 mm) diameter with an access/clearance counterbore hole of .156 inch (3.96 mm) diameter by .160 to .175 inch (4.06 to 4.45 mm) deep. Rivets. This card holder uses rivet type A as specified in AA59590 when rivet mounting is used. Length, expanded, and relaxed dimensions. The length, e

18、xpanded, and relaxed dimensions shall be as specified on figure 1. The length designator shall be as specified in AA59590 and the available lengths for this specification sheet are listed in table I. TABLE I. Additional assembly dimensions (see figure 1). 1/ PIN length designator Dimension “LENGTH“

19、.02 (0.5) Dimension “A“ (maximum) Dimension “B“ .03 (0.8) Dimension “C“ .005 (0.13) 18 1.8 (45.7) 2.10 (53.3) 1.24 (31.5) .75 (19.1) 23 2.3 (58.4) 2.60 (66.0) 1.74 (44.2) .40 (10.2) 28 2.8 (71.1) 3.10 (78.7) 2.24 (56.8) .90 (22.9) 30 3.0 (76.2) 3.30 (83.8) 2.44 (62.0) 1.10 (27.9) 33 3.3 (83.8) 3.60

20、(91.4) 2.74 (69.6) 1.40 (35.6) 35 3.5 (88.9) 3.80 (96.5) 2.94 (74.7) 1.60 (40.6) 38 3.8 (96.5) 4.10 (104.1) 3.24 (82.3) 1.90 (48.3) 43 4.3 (109.2) 4.60 (116.8) 3.74 (95.0) 2.40 (61.0) 48 4.8 (121.9) 5.10 (129.5) 4.24 (107.7) 2.90 (73.7) 53 5.3 (134.6) 5.60 (142.2) 4.74 (120.4) 3.40 (86.4) 58 5.8 (14

21、7.3) 6.10 (154.9) 5.24 (133.1) 3.90 (99.1) 63 6.3 (160.0) 6.60 (167.6) 5.74 (145.8) 4.40 (111.8) 68 6.8 (172.7) 7.10 (180.3) 6.24 (158.5) 4.90 (124.5) 73 7.3 (185.4) 7.60 (193.0) 6.74 (171.2) 5.40 (137.2) 78 7.8 (198.1) 8.10 (205.7) 7.24 (183.9) 5.90 (149.9) 83 8.3 (210.8) 8.60 (218.4) 7.74 (196.6)

22、6.40 (162.6) 88 8.8 (223.5) 9.10 (231.1) 8.24 (209.3) 6.90 (175.3) 1/ Dimensions are in inches. Millimeters, in parenthesis, are given for general information only. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/7C 4 Configuration. The confi

23、guration of a card holder shall be as specified in table II. The details of a particular configuration consist of those on figure 1, and may include those on figures 2 and 3. Card holders not requiring the following option shall leave the configuration position in the PIN blank. TABLE II. Configurat

24、ion. Configuration Applicable figures Hardware options 1 No added options W 1 and 2 Lockwasher and flat washer E 1 and 3 Screw self-locking element D 1, 2, and 3 Lockwasher, flat washer and screw self-locking element Lockwasher and flat washer (see figure 2). The use of a lockwasher and flat washer

25、located under the screw head will provide additional resistance to loosening of the card holder assembly from shock and vibration. Card holders requiring a lockwasher and flat washer shall include a suffix “W“ in the PIN (see table I, classification and notes). FIGURE 2. Lockwasher and flat washer d

26、etails. Screw self-locking element (see figure 3). The use of a self-locking element on the screw will provide a prevailing-torque for increased resistance to loosening of the card holder assembly from shock and vibration. The screw self-locking element shall be as specified in AA59590. Card holders

27、 requiring a screw self-locking element shall include configuration identifier “E“ in the PIN (see table I, classification and notes). FIGURE 3. Screw self-locking element details. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/7C 5 Lockwash

28、er, flat washer, and screw self-locking element. Card holders requiring a lockwasher, flat washer, and screw self-locking element configuration shall include a suffix “D“ in the PIN (see table I, classification and notes). NOTES. PIN. The PIN should be used for Government purposes to buy commercial

29、products to this CID specification sheet. See the classification section for PIN format example. Source of documents. Commercial Item Description AA59590 Holder, Electrical Card, Wedge Retainers, 3 Piece, Screw Actuated Drive, General Requirements For. (Copies of these documents are available online

30、 at http:/quicksearch.dla.mil or https:/assist.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 191115094.) Ordering data. Ordering data shall be as specified in AA59590. Commercial products. As part of the market analysis and research effort

31、, this CID specification sheet was coordinated with the following manufacturers of commercial products. At the time of CID specification sheet preparation and coordination, these manufacturers were known to have commercial products that would meet the requirements of this CID specification sheet. (N

32、OTE: This information should not be considered as a list of approved manufacturers or be used to restrict procurement to only the manufacturers shown.) Manufacturer CAGE Manufacturer name and address Manufacturer contact information 18915 Birtcher A Division of Pentair Electronic Packaging 7238 Trad

33、e Street San Diego, CA 921213410 Telephone: (858) 7402400 Toll Free: (800) 8547086 Facsimile: (858) 6794555 URL: 61081 Calmark A Division of Pentair Electronic Packaging 7238 Trade Street San Diego, CA 921213410 Telephone: (858) 7402400 Toll Free: (800) 8547086 Facsimile: (858) 7402430 Electronic m

34、ail: URL: 5BG68 American Circuit Card Retainers, Inc. 2310 E. Orangethorpe Avenue Anaheim, CA 928061231 Telephone: (714) 7386194 Facsimile: (714) 4460119 E-mail: URL: http:/ 3E7U8 Wakefield Solutions 200 Towerview Court Cary, NC 27513 Telephone: (919) 4692004 Facsimile: (919) 4692827 E-mail: URL

35、: Part number supersession data. This CID specification sheet PINs supersede the following manufacturers part numbers in table III and on DESC Drawing 84103 (table IV) as shown. The CID PINs listed in table III are only for length designator “28“. See table V for CID PIN construction using other av

36、ailable lengths for this specification sheet. This information is being provided to assist in reducing proliferation in the Government inventory system. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/7C 6 TABLE III. Commercial part number su

37、persession data. PIN designator AA59590/07 Vendor similar designator or type part number 1/ 2/ CAGE 18915 CAGE 61081 CAGE 5BG68 CAGE 3E7U8 BJ28 426B A2302.80H 3220BA2.80H 422B280RSB BN28 426BA A2302.80 3220BA2.80 422B280ASB BT28 426BT A2302.80T0 3220BA2.80T0 422B280TSB BV28 426BS A2302.80T2 3220BA2.

38、80T2 422B280SSB BG28 426BM MA2302.80TM2.5 3220MBA2.80TM2.5 422B280MMB BJ28W 426BLF WA2302.80H 3220WBA2.80H 422B280RSBW BN28W 426BLFA WA2302.80 3220WBA2.80 422B280ASBW BT28W 426BLFT WA2302.80T0 3220WBA2.80T0 422B280TSBW BV28W 426BLFS WA2302.80T2 3220WBA2.80T2 422B280SSBW BG28W 426BLFM MWA2302.80TM2.5

39、 3220MWBA2.80TM2.5 422B280MMBW BJ28E 426BL A2302.80HL 3220BA2.80HL 422B280RSBP BN28E 426BAL A2302.80L 3220BA2.80L 422B280ASBP BT28E 426BTL A2302.80T0L 3220BA2.80T0L 422B280TSBP BV28E 426BSL A2302.80T2L 3220BA2.80T2L 422B280SSBP BG28E 426BML MA2302.80TM2.5L 3220MBA2.80TM2.5L 422B280MMBP BJ28D 426BLFL

40、 WA2302.80HL 3220WBA2.80HL 422B280RSBWP BN28D 426BLFAL WA2302.80L 3220WBA2.80L 422B280ASBWP BT28D 426BLFTL WA2302.80T0L 3220WBA2.80T0L 422B280TSBWP BV28D 426BLFSL WA2302.80T2L 3220WBA2.80T2L 422B280SSBWP BG28D 426BLFML MWA2302.80TM2.5L 3220MWBA2.80TM2.5L 422B280MMBWP CJ28 426 2302.80H 3220CG2.80H 42

41、2B280RSG CN28 426A 2302.80 3220CG2.80 422B280ASG CT28 426T 2302.80T0 3220CG2.80T0 422B280TSG CV28 426S 2302.80T2 3220CG2.80T2 422B280SSG CG28 426M M2302.80TM2.5 3220MCG2.80TM2.5 422B280MMG CJ28W 426LF W2302.80H 3220WCG2.80H 422B280RSGW CN28W 426LFA W2302.80 3220WCG2.80 422B280ASGW CT28W 426LFT W2302

42、.80T0 3220WCG2.80T0 422B280TSGW CV28W 426LFS W2302.80T2 3220WCG2.80T2 422B280SSGW CG28W 426LFM MW2302.80TM2.5 3220MWCG2.80TM2.5 422B280MMGW See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/7C 7 TABLE III. Commerc

43、ial part number supersession data Continued. PIN designator AA59590/07 Vendor similar designator or type part number 1/ 2/ CAGE 18915 CAGE 61081 CAGE 5BG68 CAGE 3E7U8 CJ28E 426L 2302.80HL 3220CG2.80HL 422B280RSGP CN28E 426AL 2302.80L 3220CG2.80L 422B280ASGP CT28E 426TL 2302.80T0L 3220CG2.80T0L 422B2

44、80TSGP CV28E 426SL 2302.80T2L 3220CG2.80T2L 422B280SSGP CG28E 426ML M2302.80TM2.5L 3220MCG2.80TM2.5L 422B280MMGP CJ28D 426LFL W2302.80HL 3220WCG2.80HL 422B280RSGWP CN28D 426LFAL W2302.80L 3220WCG2.80L 422B280ASGWP CT28D 426LFTL W2302.80T0L 3220WCG2.80T0L 422B280TSGWP CV28D 426LFSL W2302.80T2L 3220WC

45、G2.80T2L 422B280SSGWP CG28D 426LFML MW2302.80TM2.5L 3220MWCG2.80TM2.5L 422B280MMGWP HJ28 426B3 HA2302.80H 3220BH2.80H 422B280RSH HN28 426B3A HA2302.80 3220BH2.80 422B280ASH HT28 426B3T HA2302.80T0 3220BH2.80T0 422B280TSH HV28 426B3S HA2302.80T2 3220BH2.80T2 422B280SSH HG28 426B3M MHA2302.80TM2.5 322

46、0MBH2.80TM2.5 422B280MMH HJ28W 426B3LF WHA2302.80H 3220WBH2.80H 422B280RSHW HN28W 426B3LFA WHA2302.80 3220WBH2.80 422B280ASHW HT28W 426B3LFT WHA2302.80T0 3220WBH2.80T0 422B280TSHW HV28W 426B3LFS WHA2302.80T2 3220WBH2.80T2 422B280SSHW HG28W 426B3LFM MWHA2302.80TM2.5 3220MWBH2.80TM2.5 422B280MMHW HJ28

47、E 426B3L HA2302.80HL 3220BH2.80HL 422B280RSHP HN28E 426B3AL HA2302.80L 3220BH2.80L 422B280ASHP HT28E 426B3TL HA2302.80T0L 3220BH2.80T0L 422B280TSHP HV28E 426B3SL HA2302.80T2L 3220BH2.80T2L 422B280SSHP HG28E 426B3ML MHA2302.80TM2.5L 3220MBH2.80TM2.5L 422B280MMHP HJ28D 426B3LFL WHA2302.80HL 3220WBH2.80HL 422B280RSHWP HN28D 426B3L