DLA A-A-59602-2000 TUBE SPIRAL WRAP POLYETHYLENE POLYTETRAFLUOROETHYLENE AND POLYAMIDE [Superseded DLA MIL-T-47287 A CANC NOTICE 3 DLA MIL-T-47287 A REINST NOTICE 2 DLA MIL-T-47287.pdf

1、INCH-POUNDA-A-5960231 October 2000 SUPERSEDINGMIL-T-47287A25 September 1980Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any datathat may improve this document should be sent to: Defense Supply Center Richmond(DSCR), ATTN: DSCR-VBD, 8000 Jefferson Davis Highway

2、, Richmond, VA 23297-5610.AMSC N/A FSC 9330DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.COMMERCIAL ITEM DESCRIPTIONTUBE, SPIRAL WRAP, POLYETHYLENE,POLYTETRAFLUOROETHYLENE AND POLYAMIDEThe General Services Administration has authorized the use of thiscommercial ite

3、m description for all federal agencies.1. SCOPE. This commercial item description (CID) covers spiral wrap tubing intended for useprimarily to protect and insulate electrical wiring.2. CLASSIFICATION. The spiral wrap tubing shall be classified by the following types andclasses. The type and class to

4、 be furnished shall be as specified in the acquisition order (see7.2(b).Type I - PolyethyleneType II - PolyamideType III - PolytetrafluoroethyleneClass 1 - NaturalClass 2 - Weather resistant (Types I and II only)Class 3 - Fire resistant (Type I only)3. SALIENT CHARACTERISTICS3.1 General requirements

5、. Unless otherwise specified in the acquisition order (see 7.2(c), thetubing shall be furnished in 100 foot rolls. The outside diameter (OD) of the tubes shall be asspecified in the acquisition order (see 7.2(d). Tolerance on the OD shall be 0.005 inches. If Provided by IHSNot for ResaleNo reproduct

6、ion or networking permitted without license from IHS-,-,-A-A-596022required (see 7.2(e), an assembly tool shall be provided. Unless otherwise specified in theacquisition order (see 7.2(f), the spiral wrap shall be clockwise or right-hand pitch.3.1.1 Type I, polyethylene spiral wrap tubing. Type I sp

7、iral wrap tubing shall be made frompolyethylene conforming to Type I of American Society for Testing and Materials (ASTM) D 1248,“Standard Specification for Polyethylene Plastics Extrusion Materials for Wire and Cable“ (DoDadopted). Unless otherwise specified in the acquisition order (see 7.2(g), th

8、e color shall be natural.Natural is milky white for class 1, black for class 2 and black or white for class 3. Class 3 spiralwrap tubing shall be certified as meeting V0 or V2 of Underwriters Laboratory (UL) 94, “Tests forFlammability of Plastic Materials for Parts in Devices and Appliances“ (DoD ad

9、opted). The wallthickness shall be 0.03 inches minimum for tubing less than or equal to 0.5 inches OD and 0.05inches minimum for tubing greater than 0.5 inches OD.3.1.2 Type II, polyamide spiral wrap tubing. Type II spiral wrap tubing shall be made frompolyamide conforming to group 1, class 1 of AST

10、M D 4066, “Standard Classification Systemfor Nylon Injection and Extrusion Materials (PA)“ (DoD adopted). Unless otherwise specified inthe acquisition order (see 7.2(g), the color shall be natural. Natural is milky white for class 1and black for class 2. The wall thickness shall be 0.015 inches mini

11、mum for tubing less than0.5 inches OD and 0.03 inches minimum for tubing equal to or greater than 0.5 inches OD.3.1.3 Type III, polytetrafluoroethylene spiral wrap tubing. Type III spiral wrap tubing shallbe made from polytetrafluoroethylene conforming to Type 1 of ASTM D 1710, “StandardSpecificatio

12、n for Polytetrafluoroethylene (PFTE) Rod and Heavy-Walled Tubing“ (DoDadopted). Unless otherwise specified in the acquisition order (see 7.2(g), the color shall benatural. Natural is milky white. The wall thickness shall be 0.03 inches minimum for all tubingODs.4. REGULATORY REQUIREMENTS4.1 Recovere

13、d materials. The offeror/contractor is encouraged to use recovered materials to themaximum extent practicable, in accordance with paragraph 23.403 of the Federal AcquisitionRegulation (FAR).4.2 Environmental protection. The item shall meet all applicable Environmental ProtectionAgency restrictions i

14、n effect on the date of the contract. These regulations apply to the emissionof materials hazardous to the environment or the users health and shall be met during themanufacturing, service, transportation, storage, and operation/use of the item.5. PRODUCT CONFORMANCE PROVISIONS5.1 Product conformanc

15、e. The products provided shall meet the salient characteristics of thiscommercial item description, conform to the producers own drawings, specifications, standards,and quality assurance practices, and be the same product offered for sale in the commercialmarketplace. The government reserves the rig

16、ht to require proof of such conformance.6. PACKAGING6.1 Preservation, packing, and marking. For acquisition purposes, the spiral wrap tubing shallbe preserved, packed, and marked as specified in the acquisition order (see 7.2(h).Provided by IHSNot for ResaleNo reproduction or networking permitted wi

17、thout license from IHS-,-,-A-A-5960237. NOTES7.1 Part or identification number (PIN). The following part or identification numberingprocedure is for government purposes and does not constitute a requirement for the contractor.7.2 Source of documents.7.2.1 FAR. The FAR may be obtained from the Superi

18、ntendent of Documents, U.S.Government Printing Office, Washington, DC 20402-0001.7.2.2 ASTM standards. Copies of ASTM standards may be obtained from the American Societyfor Testing and Materials, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.7.2.3 UL standards. Copies of UL standards may b

19、e obtained from Underwriters LaboratoriesInc., 333 Pfingsten Road, Northbrook, IL 60062.7.3 Ordering data. The contract or order should specify the following:a. CID document number, revision, and CID PINb. Type and class of tubing required (see 2)c. Length of tubing, if different (see 3.1)d. Outside

20、 tubing diameter (see 3.1)e. Assembly tool, if required (see 3.1)f. Pitch direction, if different (see 3.1)g. Tubing color, if different (see 3.1.1 through 3.1.3)h. Preservation, packing and marking (see 6.1)Class: A - Class 1 - NaturalB - Class 2 - Weather resistant (Types I and II only)C - Class 3

21、 - Fire resistant (Type I only)Type: 1 - Type I - Polyethylene2 - Type II - Polyamide3 - Type III - PolytetrafluoroethyleneAA59602 - X XCID numberProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-596024MILITARY INTERESTS:CIVIL AGENCYCOORDINATING ACTIVITY:Custodians:Army - ARDLA - ISGSA - 7FXEReviewer:Army - MRPreparing activity:DLA - GS(Project 9330-0125)Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-