DLA A-A-59632 B-2011 BEARING BALL ANNULAR SINGLE ROW ANGULAR CONTACT CONTACT ANGLE 33 THROUGH 45 DIMENSION SERIES 10.pdf

1、Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any data that may improve this document should be sent to: STDZNMGTdla.mil or Defense Logistics Agency Aviation VEB, 8000 Jefferson Davis Highway, Richmond, VA 23297-5616. Since contact information can change, you m

2、ay want to verify the currency of this address information using the ASSIST database at https:/assist.daps.dla.mil/. FSC 3110 METRIC A-A-59632B 28 January 2011 SUPERSEDING A-A-59632A 6 August 2004 COMMERCIAL ITEM DESCRIPTION BEARING, BALL, ANNULAR, SINGLE ROW, ANGULAR CONTACT, CONTACT ANGLE 33 THROU

3、GH 45, DIMENSION SERIES 10 The General Services Administration has authorized the use of this commercial item description for all federal agencies. 1. SCOPE. This commercial item description (CID) covers metric, single row, angular contact, annular ball bearings for general-purpose use. These bearin

4、gs are not intended for use in critical aeronautical or critical special precision applications. 2. CLASSIFICATION. The ball bearings shall be classified by the class, sizes, cage materials, shield and seal configurations, precision tolerances, lubricant and preservative requirements, and duplex mou

5、nting configurations listed below: Class 4 - dimension series 10 Sizes - bearing dimensions (see table I) Cage materials (see table II) Shield and seal configurations (see table III) Precision tolerances (see table IV) Lubricant and preservative requirements (see table V) Duplex mounting configurati

6、ons (see table VI) 3. SALIENT CHARACTERISTICS 3.1 Dimensions. Bearing boundary dimensions shall conform to the requirements specified in table I for each of the coded bearing sizes. The listed dimensions conform to the requirements Provided by IHSNot for ResaleNo reproduction or networking permitted

7、 without license from IHS-,-,-A-A-59632B 2 specified for the listed bearing sizes from dimension series 10 in the American Bearing Manufacturers Association (ABMA) Standard 20, “Radial Bearings of Ball, Cylindrical Roller, and Spherical Roller Types, Metric Design“. The bearing size shall be as spec

8、ified in the acquisition order (see 7.3(b). For unlisted bearing sizes, the dimensional and dynamic load rating requirements should also be specified in the acquisition order. TABLE I. Dimensional requirements (ABMA series 10). Bearing size code Bore diameter (mm) Outside diameter (mm) Width (mm) Ch

9、amfer r/min. (mm) Minimum shaft shoulder diameter 1(mm) Dynamic load rating (minimum) (lbs.) 00 10 26 8 0.3 12.5 67001 12 28 8 0.3 14.5 72002 15 32 9 0.3 17.5 76003 17 35 10 0.3 19.5 1,08004 20 42 12 0.6 25 1,36505 25 47 12 0.6 30 1,49006 30 55 13 1.0 36 1,92007 35 62 14 1.0 41 2,30508 40 68 15 1.0

10、46 2,36509 45 75 16 1.0 51 2,92510 50 80 16 1.0 56 2,99511 55 90 18 1.1 62 4,09012 60 95 18 1.1 67 4,19013 65 100 18 1.1 72 4,28514 70 110 20 1.1 77 5,05515 75 115 20 1.1 82 5,16016 80 125 22 1.1 87 6,64517 85 130 22 1.1 92 6,78018 90 140 24 1.5 98.5 8,22019 95 145 24 1.5 103.6 9,75020 100 150 24 1.

11、5 108.5 8,57021 105 160 26 2.0 115 10,16522 110 170 28 2.0 120 11,80524 120 180 28 2.0 130 11,99026 130 200 33 2.0 140 16,45528 140 210 33 2.0 150 16,24030 150 225 35 2.1 162 18,58032 160 240 38 2.1 172 21,06034 170 260 42 2.1 182 25,26036 180 280 46 2.1 192 28,16038 190 290 46 2.1 202 28,73040 200

12、310 51 2.1 212 32,6501 Listed for reference purposes only. Shoulder height shall be determined to provide sufficient clearance for the direct application of bearing removal force against the bearing inner ring. If the required minimum clearance is not available, an alternative non-destructive bearin

13、g removal capability shall be provided. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59632B 3 3.2 Materials. 3.2.1 Rings. The bearing ring material shall be chromium-alloy steel 52100 (UNS G52986) as specified in ASTM International (ASTM) A295

14、/A295M, “Standard Specification for High-Carbon Anti-Friction Bearing Steel“. The finished rings shall not exceed the associated billet material inclusion rating also specified in ASTM A295/A295M. Ring hardness shall be at least 58 HRC as defined in ASTM E18, “Standard Test Methods for Rockwell Hard

15、ness and Rockwell Superficial Hardness of Metallic Materials“. The grain size of the ring material shall be determined in accordance with ASTM E112, “Standard Methods for Determining Average Grain Size“. 3.2.2 Balls. The bearing ball material shall be chromium-alloy steel 52100 (UNS G52986) as speci

16、fied in ASTM A295/A295M. The finished balls shall not exceed the associated billet material inclusion rating, which is also specified in ASTM A295/A295M. Balls shall be through-hardened no less than 60 HRC and no more than 67 HRC as defined in ASTM E18. The grain size of the ball material shall be d

17、etermined in accordance with ASTM E112. 3.2.3 Cage. The bearing cage material shall be impervious to deterioration from any lubricant, preservative, solvent, or other chemical substance expected to contact the bearing during normal use or storage. Similarly, the material shall not cause any chemical

18、 deterioration of any other bearing component. Metallic cage materials shall operate from -40 F to 250 F (-40 C to 121 C). Non-metallic cage materials shall operate from -20 F to 250 F (-30 C to 121 C). Unless otherwise specified in the acquisition order, the cage material shall be one of the option

19、al coded types listed in table II (see 7.3(c). TABLE II. Cage materials. Code 1 Material type J Pressed steel M Machined bronze or brass P Molded plastic (nylon 6/6 or equal) T Machined non-metallic (phenolic) Y Pressed brass X Other (specify in acquisition order) 1 No significant changes from FF-B-

20、171/28. 3.2.4 Shields and seals. Unless otherwise specified in the acquisition order, the shield and seal configuration for the bearing shall be one of the coded options listed in table III (see 7.3(d). The acquisition order shall state which side of the outer ring (heavy shoulder or counterbore sid

21、e) the shield or seal is to be located (see 7.3(e). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59632B 4 TABLE III. Shield and seal configurations. Code 1 Configuration option A Open X Other (specify in acquisition order)1 No significant chan

22、ges from FF-B-171/28. 3.2.4.1 If a single shield or seal is required, the shield or seal material shall be as recommended by the manufacturer, unless otherwise specified in the acquisition order (see 7.3(f). The material shall be impervious to deterioration from any lubricant, preservative, solvent,

23、 or other chemical substance expected to contact the bearing during normal use or storage. Similarly, the material shall not cause any chemical deterioration of any other bearing component. The shield or seal material shall remain functionally effective at a minimum temperature range of -20 F to 250

24、 F (-30 C to 121 C) for non-metallic and -40 F to 250 F (-40 C to 121 C) for metallic materials. 3.3 Precision tolerance. The bearing precision tolerance level shall conform to Annular Bearing Engineers Committee (ABEC) class ABEC-1, ABEC-3, ABEC-5, or ABEC-7 as defined in ABMA Standard 20. The tole

25、rance class shall be one of the coded options listed in table IV (see 7.3(g). TABLE IV. Precision tolerance requirements. Code Tolerance class B ABEC-1 F ABEC-3 K ABEC-5 P ABEC-7 3.3.1 Bearing precision tolerance levels and internal clearances may be affected by the addition of shields and/or seals.

26、 Manufacturers/suppliers should be consulted for availability of desired precision tolerances when shields and/or seals are required. 3.4 Lubrication and preservation requirements. Unless otherwise specified in the acquisition order, the bearing lubricant or preservative requirement shall be as sele

27、cted from the approved coded options listed in table V (see 7.3(h). When grease fill is required, the bearing void (the airspace between the inner and outer rings of the assembled bearing) shall be 25 to 50 percent filled. Bearing preservative shall be in accordance with MIL-DTL-197, “Packaging of B

28、earings, Associated Parts and Subassemblies“. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59632B 5 TABLE V. Lubricant and preservative requirements. Code Lubricant or preservative compound B Grease in accordance with MIL-PRF-81322 E Grease in

29、 accordance with DOD-G-24508 H Grease in accordance with MIL-PRF-23827 L Grease with SRI-2 or qualified equivalent S No fill T Preservation compound in accordance with MIL-DTL-197 X Other (specify in the acquisition order) 3.5 Duplex mounting. When required, the adjoining faces of bearings used in d

30、uplex applications shall be match ground and marked for proper mounting. The duplex mounting configuration shall be one of the coded options listed in table VI. If required, the duplex mounting configuration shall be specified in the acquisition order (see 7.3(i). TABLE VI. Duplex mounting. Code Con

31、figuration option F Face to face B Back to back T Tandem U Universal (F, B, or T) 3.6 Preload. Preload requirements shall be listed in the acquisition order (see 7.3(j). 4. REGULATORY REQUIREMENTS 4.1 Recovered materials. The offeror/contractor is encouraged to use recovered materials to the maximum

32、 extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 4.2 Foreign acquisition restrictions. Unless otherwise indicated in the solicitation and resulting contract, the foreign acquisition restrictions in Section 252.225, Clause 252.225.7016, of the Defe

33、nse Federal Acquisition Regulation Supplement (DFARS) apply to products described by this CID. 5. PRODUCT CONFORMANCE PROVISIONS 5.1 Product conformance. The products provided shall meet the salient characteristics of this CID, conform to the producers own drawings, specifications, standards, and qu

34、ality assurance practices, and be the same product offered for sale in the commercial marketplace. The government reserves the right to require proof of such conformance. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59632B 6 5.2 Market accepta

35、bility. The products offered must have been previously sold either to the government or on the commercial market. 6. PACKAGING 6.1 Preservation, packing, and marking. Unless otherwise specified in the acquisition order, the bearings supplied shall be preserved, packed, and marked in accordance with

36、MIL-DTL-197 (see 7.3(k). 7. NOTES 7.1 Part or identification number (PIN). The following PIN procedure is for government purposes and does not constitute a requirement for the contractor. AA59632 4 08 J A B B U Example of reference part number: Duplex mounting code (see table VI) Lubricant and prese

37、rvative code (see table V) Precision tolerance code (see table IV) Shield and seal code (see table III) Cage material code (see table II) Bearing size code (see table I) Class 4 - dimension series 10 CID numberAA59632 - 4 08 J A B B U indicates: boundary dimension series 10; bore diameter 40 mm, out

38、side diameter 68 mm, width 15 mm; pressed steel cage; open, no shield or seal; ABEC-1 tolerance class; filled with grease in accordance with MIL-PRF-81322; universal duplex mounting. 7.2 Sources of documents. 7.2.1 DFARS and FAR. Copies of DFARS and FAR may be obtained from the Superintendent of Doc

39、uments, P.O. Box 371954, Pittsburgh, PA 15250-7954. Electronic copies of DFARS may be obtained from http:/www.acq.osd.mil/dpap/dars/dfarspgi/current/index.html. Electronic copies of FAR may be obtained from https:/www.acquisition.gov/far/. 7.2.2 Military specifications. Copies of military specificat

40、ions may be obtained from Standardization Documents Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094. Electronic copies may be obtained from https:/assist.daps.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5963

41、2B 7 7.2.3 ABMA standards. Copies of ABMA standards may be obtained from the American Bearing Manufacturers Association, 2025 M Street NW, Suite 800, Washington, DC 20036. Electronic copies may be obtained from http:/www.abma-dc.org/. 7.2.4 ASTM standards. Copies of ASTM standards may be obtained fr

42、om ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959. Electronic copies may be obtained from http:/www.astm.org/. 7.3 Ordering data. The acquisition order should specify the following information: a. CID document number, revision, and CID PIN. b. Bearing size

43、 (with dimension/load requirements if size is unlisted), if different (see 3.1). c. Cage material type (see 3.2.3). d. Shield and seal configuration (see 3.2.4). e. Location of shield or seal (see 3.2.4). f. Shield or seal material (see 3.2.4.1). g. Precision tolerance requirement (see 3.3). h. Lubr

44、icant and preservative requirements (see 3.4). i. Duplex mounting configuration, if required (see 3.5). j. Preload requirement, if required (see 3.6). k. Preservation, packing, and marking requirements (see 6.1). 7.4 Codes cross-reference. Tables VII, VIII, and IX contain cross-reference data for th

45、e PIN information as listed in FF-B-171/28 and this CID. 7.4.1 Bearing class designations. The CIDs replacing 33 of 37 associated specification sheets of FF-B-171 have been assigned class codes corresponding to ABMA dimension series. Table VII lists the FF-B-171 specification sheets, the correspondi

46、ng dimension series, the CID class codes, and the replacement CIDs. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59632B 8 TABLE VII. Federal specification to CID cross-reference. FF-B-171 specification sheets ABMA dimension series CID classcod

47、es Replacement CID numbers 1 02, 03, 10 1, 2, 4 A-A-59581 2 19 5 A-A-59582 3 10 4 A-A-59583 4 02 1 A-A-59584 5 03 2 A-A-59585 6 04 3 A-A-59586 7 02 1 A-A-59587 8 03 2 A-A-59589 9 32 8 A-A-59595 10 33 9 A-A-59596 11 02 1 A-A-59597 12 03 2 A-A-59598 13 22 6 A-A-59599 14 23 7 A-A-59600 15 19 - Canceled

48、 16 10 - Canceled 17 02 - Canceled 18 03 - Canceled 19 19 5 A-A-59623 20 10 4 A-A-59624 21 02 1 A-A-59625 22 03 2 A-A-59626 23 04 3 A-A-59627 24 10 4 A-A-59628 25 02 1 A-A-59629 26 03 2 A-A-59630 27 04 3 A-A-59631 28 10 4 A-A-59632 29 02 1 A-A-59633 30 03 2 A-A-59634 31 04 3 A-A-59635 32 32 8 A-A-59

49、636 33 33 9 A-A-59637 34 32 8 A-A-59638 35 33 9 A-A-59639 36 32 8 A-A-59640 37 33 9 A-A-59641 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59632B 9 TABLE VIII. Radial internal clearance and ABEC tolerance codes. FF-B-171/28 codes A-A-59632B codes Code Radial internal