DLA A-A-59649 C-2011 BEARINGS ROLLER TAPERED SINGLE ROW NORMAL ANGLE (TYPE TS).pdf

1、Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any data that may improve this document should be sent to: STDZNMGTdla.mil or DLA Aviation VEB, 8000 Jefferson Davis Highway, Richmond, VA 23297-5616. Since contact information can change, you may want to verify the

2、 currency of this address information using the ASSIST database at https:/assist.daps.dla.mil/. FSC 3110 INCH-POUND A-A-59649C 8 September 2011 SUPERSEDING A-A-59649B 28 September 2005 COMMERCIAL ITEM DESCRIPTION BEARINGS, ROLLER, TAPERED, SINGLE ROW, NORMAL ANGLE (TYPE TS) The General Services Admi

3、nistration has authorized the use of this commercial item description for all federal agencies. 1. SCOPE. This commercial item description (CID) covers government acquisition requirements for complete (cone with rollers and cup) single row, normal angle (type TS), tapered, roller bearings for genera

4、l-purpose use. These bearings are not intended for use in special precision applications such as on aircraft, precision ordnance or submarine equipment. 2. CLASSIFICATION. The roller bearings shall be of one type (TS) and classified by the size codes listed in table I. The column headings in table I

5、 refer to bearing characteristics defined in figure 1. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59649C 2 FIGURE 1. Bearing characteristics. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-T

6、ABLE I. Size codes and dimensions. 1For each size code there are 3 options for the PIN (see 7.1): Add a code A for cone only or a code B for cup only; use no code if for a whole bearing assembly. 2Part numbers are for reference only. Part numbers reflect the cup and cone numbers used by industry and

7、 the ABMA. Some cones and cups may be used in multiple configurations and are not limited to one bearing assembly. 3These maximum fillet radii shall be cleared by the bearing corners. 4Minus value indicates load center inside cone backface. 3 Size code 1Part number 2d D T B C R 3r 3d bd aD bD aK fac

8、torBasic dynamic load ratings (lb.) a 4Bore Outside diameterBearing width Cone width Cup width Max. shaft fillet radius Max. housing fillet radius Recommended shoulder diameters Effective load center Cone-cup Shaft Housing Radial001 A2037-A2126 0.3750 1.2595 0.3940 0.4246 0.3125 0.05 0.05 0.59 0.53

9、1.02 1.14 1.44 1900 -0.12 002 A4050-A4138 0.5000 1.3775 0.4330 0.4326 0.3437 0.05 0.05 0.73 0.67 1.14 1.26 1.29 2100 -0.10 003 00050-00150 0.5000 1.5000 0.5313 0.5540 0.4375 0.06 0.06 0.75 0.65 1.30 1.34 2.12 3400 -0.20 004 L21549-L21511 0.6250 1.3775 0.4330 0.4330 0.3430 0.05 0.05 0.85 0.77 1.14 1.

10、28 1.83 2500 -0.13 005 A6062-A6157 0.6250 1.5745 0.4730 0.4391 0.3750 0.05 0.05 0.87 0.81 1.34 1.46 1.11 2200 -0.06 006 A6062-A6162 0.6250 1.6250 0.4687 0.4391 0.3437 0.05 0.05 0.87 0.81 1.36 1.46 1.11 2200 -0.06 007 03062-03162 0.6250 1.6250 0.5625 0.5780 0.4375 0.05 0.08 0.85 0.79 1.34 1.48 1.88 3

11、900 -0.20 008 17580-17520 0.6250 1.6875 0.6563 0.6563 0.5313 0.06 0.06 0.91 0.83 1.44 1.54 1.76 5100 -0.23 009 05062-05185 0.6250 1.8504 0.5662 0.5662 0.4375 0.06 0.05 0.93 0.83 1.59 1.67 1.64 4400 -0.16 010 09062-09195 0.6250 1.9380 0.7813 0.8480 0.5625 0.03 0.05 0.87 0.85 1.65 1.75 2.20 6900 -0.36

12、 011 LM11749-LM11710 0.6875 1.5700 0.5450 0.5750 0.4200 0.05 0.05 0.91 0.85 1.34 1.46 2.04 4000 -0.20 012 A6075-A6157 0.7500 1.5745 0.4730 0.4391 0.3750 0.04 0.05 0.94 0.91 1.34 1.46 1.11 2200 -0.06 013 A6075-A6162 0.7500 1.6250 0.4687 0.4391 0.3437 0.04 0.05 0.94 0.91 1.36 1.46 1.11 2200 -0.06 014

13、4A-6 0.7500 1.7500 0.5000 0.4688 0.3750 0.06 0.06 1.00 0.93 1.50 1.16 1.22 3500 -0.07 015 LM11949-LM11910 0.7500 1.7810 0.6100 0.6550 0.4750 0.05 0.05 0.98 0.93 1.56 1.63 1.94 5400 -0.22 016 05075-05185 0.7500 1.8504 0.5662 0.5662 0.4375 0.05 0.05 0.98 0.93 1.59 1.67 1.64 4400 -0.16 017 09067-09195

14、0.7500 1.9380 0.7100 0.7500 0.5625 0.05 0.05 1.00 0.94 1.65 1.75 2.20 6900 -0.29 018 09074-09195 0.7500 1.9380 0.7813 0.8480 0.5625 0.06 0.05 1.02 0.94 1.65 1.75 2.20 6900 -0.36 019 09074-09194 07500 1.9380 0.9063 0.8480 0.6875 0.06 0.14 1.02 0.94 1.54 1.75 2.20 6900 -0.36 020 09078-09195 0.7500 1.9

15、380 0.7813 0.8480 0.5625 0.05 0.05 1.00 0.94 1.65 1.75 2.20 6900 -0.36 021 09067-09194 0.7500 1.9380 0.8350 0.7500 0.6875 0.05 0.14 1.00 0.94 1.54 1.75 2.20 6900 -0.29 A-A-59649C Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TABLE I. Size codes and

16、 dimensions - Continued. 1For each size code there are 3 options for the PIN (see 7.1): Add a code A for cone only or a code B for cup only; use no code if for a whole bearing assembly. 2Part numbers are for reference only. Part numbers reflect the cup and cone numbers used by industry and the ABMA.

17、 Some cones and cups can be used in multiple configurations and are not limited to one bearing assembly. 3These maximum fillet radii shall be cleared by the bearing corners. 4Minus value indicates load center inside cone backface. 4 Size code 1Part number 2d D T B C R 3r 3d bd aD bD aK factorBasic d

18、ynamic load ratings (lb.) a 4Bore Outside diameterBearing width Cone width Cup width Max. shaft fillet radius Max. housing fillet radius Recommended shoulder diameters Effective load center Cone-cup Shaft Housing Radial022 09067-09196 0.7500 1.9380 0.8350 0.7500 0.6875 0.05 0.06 1.00 0.94 1.63 1.75

19、2.20 6900 -0.29 023 1775-1729 0.7500 2.2400 0.7625 0.7810 0.6250 0.06 0.05 1.06 0.98 1.93 2.01 1.90 7300 -0.27 024 12580-12520 0.8125 1.9380 0.7813 0.7813 0.6250 0.06 0.06 1.12 1.02 1.67 1.79 1.81 7000 -0.28 025 M12649-M12610 0.8437 1.9687 0.6900 0.7200 0.5500 0.05 0.05 1.14 1.00 1.73 1.81 2.10 7200

20、 -0.25 026 LL52549-LL52510 0.8750 1.6563 0.4400 0.4400 0.3400 0.05 0.05 1.08 1.02 1.44 1.56 1.47 2700 -0.07 027 07807-07196 0.8750 1.9687 0.5313 0.5614 0.3750 0.05 0.04 1.12 1.06 1.75 1.85 1.45 4800 -0.11 028 M12648-M12610 0.8750 1.9687 0.6900 0.7200 0.5500 0.05 0.05 1.12 1.04 1.73 1.81 2.10 7200 -0

21、.25 029 1380-1328 0.8750 2.0625 0.7625 0.7940 0.5625 0.06 0.06 1.16 1.06 1.77 1.91 2.00 7800 -0.30 030 1380-1329 0.8750 2.1250 0.7625 0.7940 0.5625 0.06 0.06 1.16 1.06 1.81 1.93 2.00 7800 -0.30 031 1755-1729 0.8750 2.2400 0.7625 0.7810 0.6250 0.05 0.05 1.14 1.08 1.93 2.01 1.90 7300 -0.27 032 1280-12

22、20 0.8750 2.2500 0.0750 0.8750 0.6875 0.03 0.06 1.16 1.14 1.93 2.05 1.69 8900 -0.27 033 1975-1932 0.8750 2.3125 0.7500 0.7620 0.5937 0.03 0.05 1.14 1.10 2.05 2.13 1.77 7800 -0.23 034 2684-2631 0.8750 2.6150 0.9375 1.0013 0.7500 0.06 0.05 1.24 1.14 2.28 2.36 2.30 12400 -0.37 035 07093-07196 0.9375 1.

23、9687 0.5313 0.5614 0.3750 0.06 0.04 1.20 1.12 1.75 1.85 1.45 4800 -0.11 036 L44640-L44610 0.9375 1.9800 0.5600 0.5800 0.4200 0.06 0.05 1.20 1.12 1.75 1.85 1.56 4900 -0.13 037 1779-1729 0.9375 2.2400 0.7625 0.7810 0.6250 0.03 0.05 1.16 1.12 1.93 2.01 1.90 7300 -0.27 038 3659-3620 0.9375 2.4375 1.1250

24、 1.1975 0.9375 0.09 0.13 1.40 1.24 2.05 2.27 2.07 14200 -0.47 039 07100-07196 1.0000 1.9687 0.5313 0.5614 0.3750 0.04 0.04 1.20 1.16 1.75 1.85 1.45 4800 -0.11 040 07100-S-07196 1.0000 1.9687 0.5313 0.5614 0.3750 0.06 0.04 1.24 1.16 1.75 1.85 1.45 4800 -0.11 041 L44642-L44610 1.0000 1.9800 0.5600 0.5

25、800 0.4200 0.14 0.05 1.42 1.16 1.75 1.85 1.56 4900 -0.13 A-A-59649C Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TABLE I. Size codes and dimensions - Continued. 1For each size code there are 3 options for the PIN (see 7.1): Add a code A for cone o

26、nly or a code B for cup only; use no code if for a whole bearing assembly. 2Part numbers are for reference only. Part numbers reflect the cup and cone numbers used by industry and the ABMA. Some cones and cups can be used in multiple configurations and are not limited to one bearing assembly. 3These

27、 maximum fillet radii shall be cleared by the bearing corners. 4Minus value indicates load center inside cone backface. 5 5 Size code 1Part number 2d D T B C R 3r 3d bd aD bD aK factorBasic dynamic load ratings (lb.) a 4Bore Outside diameterBearing width Cone width Cup width Max. shaft fillet radius

28、 Max. housing fillet radius Recommended shoulder diameters Effective load center Cone-cup Shaft Housing Radial042 L44643-L44610 1.0000 1.9800 0.5600 0.5800 0.4200 0.05 0.05 1.24 1.16 1.75 1.85 1.56 4900 -0.13 043 07100-07204 1.0000 2.0470 0.5910 0.5614 0.5000 0.04 0.05 1.20 1.16 1.77 1.89 1.45 4800

29、-0.11 044 1780-1729 1.0000 2.2400 0.7625 0.7810 0.6250 0.03 0.05 1.20 1.18 1.93 2.01 1.90 7300 -0.27 045 M84548-M84510 1.0000 2.6500 0.7650 0.7650 0.5800 0.06 0.06 1.42 1.30 1.91 2.13 1.07 7900 -0.12 046 1986-1932 1.0000 2.3125 0.7500 0.7620 0.5937 0.05 0.05 1.28 1.20 2.05 2.13 1.77 7800 -0.23 047 M

30、84249-M84210 1.0000 2.3437 0.9200 0.9100 0.7200 0.03 0.06 1.42 1.27 1.95 2.20 1.07 9300 -0.20 048 15578-15523 1.0000 2.3750 0.7812 0.6875 0.6250 0.05 0.06 1.28 1.20 2.01 2.13 1.69 7500 -0.20 049 15101-15243 1.0000 2.4375 0.7500 0.8125 0.5625 0.03 0.08 1.28 1.24 2.13 2.28 1.67 8200 -0.23 050 15100-15

31、245 1.0000 2.4409 0.7500 0.8125 0.5625 0.14 0.05 1.50 1.24 2.17 2.28 1.67 8200 -0.23 051 15101-15245 1.0000 2.4409 0.7500 0.8125 0.5625 0.03 0.05 1.28 1.24 2.17 2.28 1.67 8200 -0.23 052 15102-15245 1.0000 2.4409 0.7500 0.8125 0.5625 0.06 0.05 1.34 1.24 2.17 2.28 1.67 8200 -0.23 053 15101-15244 1.000

32、0 2.4409 0.8125 0.8125 0.6250 0.03 0.05 1.28 1.24 2.17 2.28 1.67 8200 -0.23 054 15101-15250 1.0000 2.5000 0.8125 0.8125 0.6250 0.03 0.05 1.28 1.24 2.20 2.32 1.67 8200 -0.23 055 15101-15250X 1.0000 2.5000 0.8125 0.8125 0.6250 0.03 0.06 1.28 1.24 2.17 2.32 1.67 8200 -0.23 056 M86643-M86610 1.0000 2.53

33、12 0.8438 0.8438 0.6563 0.06 0.06 1.50 1.44 2.13 2.40 1.07 9700 -0.13 057 2687-2631 1.0000 2.6150 0.9375 1.0013 0.7500 0.05 0.05 1.32 1.24 2.28 2.36 2.30 12400 -0.37 058 02473-02420 1.0000 2.6875 0.8750 0.8750 0.6875 0.03 0.06 1.36 1.32 2.32 2.48 1.40 10400 -0.20 059 HM88630-HM88610 1.0000 2.8438 1.

34、0000 1.0000 0.7812 0.03 0.09 1.56 1.56 2.36 2.72 1.07 12300 -0.18 060 3189-3120 1.0000 2.8593 1.1875 1.1810 0.9375 0.03 0.13 1.40 1.38 2.40 2.64 1.76 15200 -0.40 061 L44649-L44610 1.0625 1.9800 0.5600 0.5800 0.4200 0.14 0.05 1.48 1.22 1.75 1.85 1.56 4900 -0.13 A-A-59649C Provided by IHSNot for Resal

35、eNo reproduction or networking permitted without license from IHS-,-,-TABLE I. Size codes and dimensions - Continued. 1For each size code there are 3 options for the PIN (see 7.1): Add a code A for cone only or a code B for cup only; use no code if for a whole bearing assembly. 2Part numbers are for

36、 reference only. Part numbers reflect the cup and cone numbers used by industry and the ABMA. Some cones and cups can be used in multiple configurations and are not limited to one bearing assembly. 3These maximum fillet radii shall be cleared by the bearing corners. 4Minus value indicates load cente

37、r inside cone backface. 6 Size code 1Part number 2d D T B C R 3r 3d bd aD bD aK factorBasic dynamic load ratings (lb.) a 4Bore Outside diameterBearing width Cone width Cup width Max. shaft fillet radius Max. housing fillet radius Recommended shoulder diameters Effective load center Cone-cup Shaft Ho

38、using Radial062 15580-15523 1.0625 2.3750 0.7812 0.6875 0.6250 0.14 0.06 1.52 1.26 2.01 2.13 1.69 7500 -0.20 063 15106-15245 1.0625 2.4409 0.7500 0.8125 0.5625 0.03 0.05 1.32 1.30 2.17 2.28 1.67 8200 -0.23 064 2688-2631 1.0625 2.6150 0.9375 1.0013 0.7500 0.06 0.05 1.38 1.30 2.28 2.36 2.30 12400 -0.3

39、7 065 1985-1930 1.1250 2.2400 0.7813 0.7620 0.6250 0.03 0.03 1.34 1.32 2.01 2.11 1.77 7800 -0.23 066 15590-15520 1.1250 2.2500 0.6875 0.6875 0.5313 0.14 0.06 1.56 1.32 2.01 2.09 1.69 7500 -0.20 067 1985-1932 1.1250 2.3125 0.7500 0.7620 0.5937 0.03 0.05 1.34 1.32 2.05 2.13 1.77 7800 -0.23 068 1988-19

40、32 1.1250 2.3125 0.7500 0.7620 0.5937 0.14 0.05 1.56 1.32 2.05 2.13 1.77 7800 -0.23 069 15590-15523 1.1250 2.3750 0.7812 0.6875 0.6250 0.14 0.06 1.56 1.32 2.01 2.13 1.69 7500 -0.20 070 1985-1931 1.1250 2.3750 0.7813 0.7620 0.6250 0.03 0.05 1.34 1.32 2.05 2.17 1.77 7800 -0.23 071 15113-15243 1.1250 2

41、.4375 0.7500 0.8125 0.5625 0.03 0.08 1.36 1.34 2.13 2.28 1.67 8200 -0.23 072 15113-15245 1.1250 2.4409 0.7500 0.8125 0.5625 0.03 0.05 1.36 1.34 2.11 2.28 1.67 8200 -0.23 073 15112-15245 1.1250 2.4409 0.7500 0.8125 0.5625 0.14 0.05 1.57 1.34 2.17 2.28 1.67 8200 -0.23 074 M86647-M86610 1.1250 2.5312 0

42、.8438 0.8438 0.6563 0.06 0.06 1.57 1.50 2.13 2.40 1.07 9700 -0.13 075 2689-2631 1.1250 2.6150 0.9375 1.0013 0.7500 0.05 0.05 1.42 1.34 2.28 2.36 2.30 12400 -0.37 076 2474-2420 1.1250 2.6875 0.8750 0.9375 0.6875 0.03 0.06 1.42 1.38 2.36 2.48 1.72 10900 -0.26 077 02474-02420 1.1250 2.6875 0.8750 0.875

43、0 0.6875 0.03 0.06 1.44 1.42 2.32 2.48 1.40 10400 -0.20 078 2578-2523 1.1250 2.7500 0.9375 0.9983 0.7500 0.09 0.05 1.54 1.38 2.40 2.52 2.14 13500 -0.34 079 26112-26283 1.1250 2.8346 0.7480 0.7450 0.6250 0.06 0.06 1.46 1.38 2.44 2.56 1.62 9500 -0.16 080 26112-26283-S 1.1250 2.8346 0.7480 0.7450 0.625

44、0 0.06 0.08 1.46 1.38 2.44 2.56 1.62 9500 -0.16 081 3192-3120 1.1250 2.8593 1.1875 1.1810 0.9375 0.14 0.13 1.71 1.46 2.40 2.64 1.76 15200 -0.40 082 3198-3120 1.1250 2.8593 1.1875 1.1810 0.9375 0.05 0.13 1.54 1.46 2.40 2.64 1.76 15200 -0.40 A-A-59649C Provided by IHSNot for ResaleNo reproduction or n

45、etworking permitted without license from IHS-,-,-TABLE I. Size codes and dimensions - Continued. 1For each size code there are 3 options for the PIN (see 7.1): Add a code A for cone only or a code B for cup only; use no code if for a whole bearing assembly. 2Part numbers are for reference only. Part

46、 numbers reflect the cup and cone numbers used by industry and the ABMA. Some cones and cups can be used in multiple configurations and are not limited to one bearing assembly. 3These maximum fillet radii shall be cleared by the bearing corners. 4Minus value indicates load center inside cone backfac

47、e. 7 7 Size code 1Part number 2d D T B C R 3r 3d bd aD bD aK factorBasic dynamic load ratings (lb.) a 4Bore Outside diameterBearing width Cone width Cup width Max. shaft fillet radius Max. housing fillet radius Recommended shoulder diameters Effective load center Cone-cup Shaft Housing Radial083 319

48、8-3130 1.1250 2.8593 1.1875 1.1810 0.9375 0.05 0.03 1.54 1.46 2.48 2.64 1.76 15200 -0.40 084 02872-02820 1.1250 2.8750 0.8750 0.8750 0.6875 0.03 0.13 1.48 1.46 2.44 2.68 1.29 10600 -0.15 085 17119-17244 1.1875 2.4409 0.6300 0.6522 0.5625 0.06 0.06 1.46 1.36 2.13 2.24 1.53 7000 -0.14 086 M86649-M8661

49、0 1.1875 2.5312 0.8438 0.8438 0.6563 0.06 0.06 1.61 1.50 2.13 2.40 1.07 9700 -0.13 087 2558-2523 1.1875 2.7500 0.9375 0.9983 0.7500 0.09 0.05 1.57 1.44 2.40 2.52 2.14 13500 -0.34 088 3187-3120 1.1875 2.8593 1.1875 1.1810 0.9375 0.03 0.13 1.54 1.52 2.40 2.64 1.76 15200 -0.40 089 08125-08231 1.2500 2.3125 0.5781 0.5937 0.4219 0.04 0.04 1.48 1.42 2.05 2.17 1.23 5200 -0.05 090 LM67048-LM6701D 1.2500 2.3280 0.6250 0.6600 0.46