DLA A-A-59650 B-2011 BEARINGS ROLLER TAPERED SINGLE ROW NORMAL ANGLE FLANGED CUP (TYPE TSF).pdf

1、Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any data that may improve this document should be sent to: STDZNMGTdla.mil or DLA Aviation VEB, 8000 Jefferson Davis Highway, Richmond, VA 23297-5616. Since contact information can change, you may want to verify the

2、 currency of this address information using the ASSIST database at https:/assist.daps.dla.mil/. FSC 3110 INCH-POUND A-A-59650B 8 September 2011 SUPERSEDING A-A-59650A 22 May 2006 COMMERCIAL ITEM DESCRIPTION BEARINGS, ROLLER, TAPERED, SINGLE ROW, NORMAL ANGLE, FLANGED CUP (TYPE TSF) The General Servi

3、ces Administration has authorized the use of this commercial item description for all federal agencies. 1. SCOPE. This commercial item description (CID) covers government acquisition requirements for complete (cone with rollers and cup) single row, tapered, roller bearings with normal angle, flanged

4、 cup (type TSF) for general-purpose use. These bearings are not intended for use in special precision applications such as on aircraft, precision ordnance, or submarine equipment. 2. CLASSIFICATION. The roller bearings shall be of one type (TSF) and classified by the size codes listed in table I. Th

5、e column headings in table I refer to bearing characteristics defined in figure 1. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59650B 2 FIGURE 1. Bearing characteristics. Provided by IHSNot for ResaleNo reproduction or networking permitted wi

6、thout license from IHS-,-,-TABLE I. Size codes and dimensions. 1For each code size code there are 3 options for the PIN (see 7.1): Add a code A for cone only or a code B for cup only, use no code if for a whole bearing assembly. 2Part numbers are for reference only. Part numbers reflect the cup and

7、cone numbers used by industry and the ABMA. Some cones and cups may be used in multiple configurations and are not limited to one bearing assembly. 3These maximum fillet radii shall be cleared by the bearing corners. 4Minus value indicates load center inside cone backface. 3Size code 1Part number 2d

8、 D T T 1B C R 3D 1C 1d bd aD aK factorBasic dynamic load ratings (lb.) a 4Bore Outside diameterBearing width Standout Cone width Cup width Max. shaft fillet radiusFlange Backing shoulder diameters Effective load center Cone-cup Diameter Width Shaft Housing Radial 001 A4050 - A4138-B 0.5000 1.3775 0.

9、4330 0.1823 0.4326 0.3437 0.05 1.4985 0.0930 0.73 0.67 1.32 1.29 2100 -0.10 002 A4059 - A4138-B 0.5906 1.3775 0.4330 0.1823 0.4326 0.3437 0.03 1.4985 0.0930 0.77 0.75 1.32 1.29 2100 -0.10 003 17580 - 17520-B 0.6250 1.6875 0.6563 0.2500 0.6563 0.5315 0.06 1.8085 0.1250 0.91 0.83 1.59 1.76 5100 -0.23

10、004 05062 - 05185-B 0.6250 1.8504 0.5662 0.2377 0.5662 0.4375 0.06 2.0024 0.1090 0.93 0.83 1.75 1.64 4400 -0.16 005 A6075 - A6157-B 0.7500 1.5745 0.4730 0.1910 0.4391 0.3750 0.04 1.6955 0.0930 0.94 0.91 1.50 1.11 2200 -0.06 006 09067 - 09195-A-B 0.7500 1.9380 0.7100 0.2755 0.7500 0.5625 0.05 2.0898

11、0.1280 1.00 0.94 1.83 2.20 6900 -0.29 007 1380 - 1328-B 0.8750 2.0625 0.7625 0.3560 0.7940 0.5625 0.06 2.2147 0.1560 1.16 1.06 1.97 2.00 7800 -0.30 008 1779 - 1729-B 0.9375 2.2400 0.7625 0.2935 0.7810 0.6250 0.03 2.3920 0.1560 1.16 1.12 2.09 1.90 7300 -0.27 009 3659 - 3620-B 0.9375 2.4375 1.1250 0.3

12、750 1.1975 0.9375 0.09 2.6209 0.1875 1.40 1.24 2.32 2.07 14200 -0.47 010 07100 - 07196-B 1.0000 1.9687 0.5313 0.2657 0.5614 0.3750 0.04 2.1209 0.1094 1.20 1.16 1.93 1.45 4800 -0.11 011 07100 - 07204-B 1.0000 2.0470 0.5910 0.2000 0.5614 0.5000 0.04 2.1990 0.1090 1.20 1.16 1.97 1.45 4800 -0.11 012 171

13、8 - 1729-B 1.0000 2.2400 0.7625 0.2935 0.7810 0.6250 0.03 2.3920 0.1560 1.20 1.18 2.09 1.90 7300 -0.27 013 15101 - 15250-B 1.0000 2.5000 0.8125 0.3437 0.8125 0.6250 0.03 2.6522 0.1562 1.28 1.24 2.36 1.67 8200 -0.23 014 15580 - 15520-B 1.0625 2.2500 0.6875 0.3125 0.6875 0.5313 0.14 2.4022 0.1563 1.52

14、 1.26 2.17 1.69 7500 -0.20 015 15590 - 15520-B 1.1250 2.2500 0.6875 0.3125 0.6875 0.5313 0.14 2.4022 0.1563 1.56 1.32 2.17 1.69 7500 -0.20 016 1985 - 1931-B 1.1250 2.3750 0.7813 0.3125 0.7620 0.6250 0.03 2.5270 0.1562 1.34 1.32 2.24 1.77 8300 -0.23 017 02474 - 02420-B 1.1250 2.6875 0.8750 0.3437 0.8

15、750 0.6875 0.03 2.8397 0.1562 1.44 1.42 2.56 1.40 10400 -0.20 018 3198 - 3120-B 1.1250 2.8593 1.1875 0.4375 1.1810 0.9375 0.05 3.0433 0.1875 1.54 1.46 2.72 1.76 15200 -0.40 019 17119 - 17244-B 1.1875 2.4409 0.6300 0.2075 0.6522 0.5625 0.06 2.5930 0.1400 1.46 1.36 2.32 1.53 7000 -0.14 020 02476 - 024

16、20-B 1.2500 2.6875 0.8750 0.3437 0.8750 0.6875 0.03 2.8397 0.1562 1.54 1.52 2.32 1.40 10400 -0.20 021 02475 - 02420-B 1.2500 2.6875 0.8750 0.3437 0.8750 0.6875 0.14 2.8397 0.1562 1.75 1.52 2.56 1.40 10400 -0.20 A-A-59650B Provided by IHSNot for ResaleNo reproduction or networking permitted without l

17、icense from IHS-,-,-TABLE I. Size codes and dimensions. 1For each code size code there are 3 options for the PIN (see 7.1): Add a code A for cone only or a code B for cup only, use no code if for a whole bearing assembly. 2Part numbers are for reference only. Part numbers reflect the cup and cone nu

18、mbers used by industry and the ABMA. Some cones and cups may be used in multiple configurations and are not limited to one bearing assembly. 3These maximum fillet radii shall be cleared by the bearing corners. 4Minus value indicates load center inside cone backface. 4Size code 1Part number 2d D T T

19、1B C R 3D 1C 1d bd aD aK factorBasic dynamic load ratings (lb.) a 4Bore Outside diameterBearing width Standout Cone width Cup width Max. shaft fillet radiusFlange Backing shoulder diameters Effective load center Cone-cup Diameter Width Shaft Housing Radial 022 2580 - 2523-B 1.2500 2.7500 0.9375 0.34

20、35 0.9983 0.7500 0.03 2.9020 0.1560 1.52 1.48 2.60 2.14 13500 -0.34 023 2581 - 2523-B 1.3125 2.7500 0.9375 0.3435 0.9983 0.7500 0.03 2.9020 0.1560 1.56 1.54 2.60 2.14 13500 -0.34 024 2585 - 2523-B 1.3125 2.7500 0.9375 0.3435 0.9983 0.7500 0.14 2.9020 0.1560 1.77 1.54 2.60 2.14 13500 -0.34 025 3196 -

21、 3120-B 1.3125 2.8593 1.1875 0.4375 1.1810 0.9375 0.14 3.0433 0.1875 1.85 1.59 2.72 1.76 15200 -0.40 026 31594 - 31520-B 1.3750 3.0000 1.1563 0.4063 1.1250 0.9375 0.06 3.1836 0.1875 1.81 1.71 2.91 1.45 15200 -0.30 027 31597 - 31520-B 1.4375 3.0000 1.1563 0.4063 1.1250 0.9375 0.14 3.1836 0.1875 2.01

22、1.75 2.91 1.45 15200 -0.30 028 13889 - 13836-B 1.5000 2.5625 0.5000 0.2340 0.4688 0.3750 0.06 2.6835 0.1090 1.77 1.67 2.48 1.69 4500 -0.03 029 19150 - 19268-B 1.5000 2.6875 0.6250 0.2968 0.6504 0.4688 0.06 2.8397 0.1406 1.77 1.69 2.64 1.31 8300 -0.06 030 19150 - 19283-B 1.5000 2.8346 0.6700 0.2475 0

23、.6504 0.5625 0.06 2.9865 0.1400 1.77 1.69 2.68 1.31 8300 -0.06 031 16150 - 16484-B 1.5000 2.8440 0.8125 0.3438 0.8125 0.6250 0.14 2.9960 0.1563 1.95 1.69 2.72 1.45 9200 -0.16 032 3490 - 3420-B 1.5000 3.1250 1.1563 0.4063 1.1721 0.9375 0.14 3.3090 0.1875 2.05 1.80 2.99 1.60 16800 -0.34 033 28150 - 28

24、315-B 1.5000 3.1496 0.8270 0.0583 0.8244 0.6250 0.06 3.3015 0.1563 1.79 1.71 2.87 1.45 16000 -0.19 034 3382 - 3320-B 1.5625 3.1562 1.1563 0.4063 1.1965 0.9375 0.14 3.3396 0.1875 2.05 1.79 3.03 2.14 18500 -0.43 035 11162 - 11300-B 1.6250 3.0000 0.7090 0.2871 0.6844 0.5625 0.06 3.1836 0.1406 1.93 1.83

25、 2.87 1.20 7800 -0.03 036 26882 - 26822-B 1.6250 3.1250 0.9375 0.3438 0.1000 0.7500 0.14 3.2772 0.1563 2.13 1.85 2.99 1.83 14700 -0.29 037 3877 - 3820-B 1.6250 3.3750 1.1875 0.4375 1.1875 .9375 0.14 3.5270 0.1875 2.24 1.98 3.27 1.45 2.0000 -0.32 038 LL103049 - LL103010-B 1.7500 2.8125 0.5000 0.2350

26、0.5000 0.3750 0.06 2.9225 0.1100 2.01 1.91 2.72 1.91 5900 -0.05 039 L102849 - L102810-B 1.7500 2.8750 0.7188 0.2500 0.7188 0.5938 0.06 3.0000 0.1250 2.01 1.93 2.80 1.83 9300 -0.15 040 3578 - 3525-B 1.7500 3.4375 1.1875 0.4370 1.2160 0.9375 0.14 3.6215 0.1870 2.24 2.01 3.23 1.91 18100 -0.40 041 49175

27、 - 49368-B 1.7500 3.6875 1.2500 4.6885 1.2500 1.0000 0.14 3.9073 0.2188 2.32 2.09 3.50 1.62 22000 -0.36 042 438 - 432-B 1.7500 3.7500 1.0938 0.4376 1.1772 0.8750 0.14 3.9640 0.2188 2.24 2.01 3.43 2.05 20500 -0.36 A-A-59650B Provided by IHSNot for ResaleNo reproduction or networking permitted without

28、 license from IHS-,-,-TABLE I. Size codes and dimensions. 1For each code size code there are 3 options for the PIN (see 7.1): Add a code A for cone only or a code B for cup only, use no code if for a whole bearing assembly. 2Part numbers are for reference only. Part numbers reflect the cup and cone

29、numbers used by industry and the ABMA. Some cones and cups may be used in multiple configurations and are not limited to one bearing assembly. 3These maximum fillet radii shall be cleared by the bearing corners. 4Minus value indicates load center inside cone backface. 5Size code 1Part number 2d D T

30、T 1B C R 3D 1C 1d bd aD aK factorBasic dynamic load ratings (lb.) a 4Bore Outside diameterBearing width Standout Cone width Cup width Max. shaft fillet radiusFlange Backing shoulder diameters Effective load center Cone-cup Diameter Width Shaft Housing Radial 043 18690 - 18620-B 1.8125 3.1250 0.6875

31、0.2968 0.6875 0.5313 0.11 3.3086 0.1406 2.20 2.01 3.03 1.56 8500 -0.08 044 25592 - 25521-B 1.8125 3.2700 0.9375 0.3438 1.0000 0.7500 0.14 3.4220 0.1563 2.28 2.05 3.15 1.74 14500 -0.25 045 359-S - 354-B 1.8125 3.3465 0.8125 0.3125 0.8540 0.6875 0.09 3.5299 0.1875 2.17 2.01 3.23 1.91 13300 -0.19 046 2

32、984 - 2924-B 1.8125 3.3465 1.0000 0.3750 1.0082 0.8125 0.14 3.5340 0.1875 2.28 2.05 3.23 1.69 15100 -0.25 047 436 - 432-B 1.8125 3.7500 1.0938 0.4376 1.1772 0.8750 0.14 3.9640 0.2188 2.32 2.05 3.43 2.05 20500 -0.36 048 65390 - 65320-B 1.9375 4.5000 1.7500 0.6563 1.7500 1.3750 0.14 4.7772 0.2813 2.76

33、 2.36 4.21 1.36 35700 -0.49 049 L305649 - L305610-B 2.0000 3.1875 0.7188 0.2813 1.7188 0.5625 0.06 3.3085 0.1250 2.28 2.20 3.07 1.64 9900 -0.10 050 18790 - 18720-B 2.0000 3.3465 0.6875 0.2968 0.6875 0.5313 0.14 3.4870 0.1406 2.44 2.20 3.23 1.44 8500 -0.03 051 368A - 362-B 2.0000 3.5433 0.7874 0.3499

34、 0.8750 0.6250 0.14 3.7268 0.1875 2.44 2.20 3.39 1.83 14000 -0.17 052 3780 - 3720-B 2.0000 3.6718 1.1875 0.4375 1.1930 0.9375 0.14 3.8558 0.1875 2.52 2.28 3.54 1.73 19700 -0.32 053 49585 - 49520-B 2.0000 4.0000 1.2500 0.4688 1.2500 1.0000 0.14 4.2148 0.2188 2.60 2.32 3.86 1.46 21300 -0.28 054 529 -

35、522-B 2.0000 4.0000 1.3750 0.5625 1.4200 1.0625 0.03 4.2460 0.2500 2.32 2.28 3.82 2.05 26400 -0.50 055 529X - 522-B 2.0000 4.0000 1.3750 0.5625 1.4200 1.0625 0.14 4.2460 0.2500 2.56 2.28 3.82 2.05 26400 -0.50 056 65395 - 65320-B 2.0000 4.5000 1.7500 0.6563 1.7500 1.3750 0.14 4.7772 0.2813 2.83 2.36

36、4.21 1.36 35700 -0.49 057 28584 - 28521-B 2.0625 3.6250 0.9688 0.3437 1.0000 0.7813 0.14 3.7772 0.1582 2.56 2.28 3.50 1.55 16000 -0.19 058 33895 - 33820-B 2.1250 3.6718 1.0938 0.4063 1.1250 0.8750 0.06 3.8558 0.1875 2.48 2.36 3.58 1.77 20900 -0.30 059 539 - 532-B 2.1250 4.3750 1.5000 0.5625 1.4550 1

37、.1875 0.14 4.6210 0.2500 2.68 2.40 3.94 1.97 27600 -0.48 060 621 - 612-B 2.1250 4.7500 1.6250 0.6562 1.6250 1.2500 0.14 5.0272 0.2812 2.76 2.48 4.33 1.86 33200 -0.55 061 L507949 - L507910-B 2.2500 3.4375 0.7188 0.2813 0.7188 0.5625 0.06 3.5625 0.1250 2.56 2.44 3.35 1.50 9400 -0.03 062 387A - 382-B 2

38、.2500 3.8125 0.8268 0.3125 0.8640 0.7018 0.14 3.9960 0.1875 2.72 2.44 3.70 1.65 14800 -0.12 063 28682 - 28622-B 2.2500 3.8437 0.9688 0.3592 0.9688 0.7656 0.14 3.9960 0.1560 2.76 2.48 3.70 1.45 16800 -0.13 A-A-59650B Provided by IHSNot for ResaleNo reproduction or networking permitted without license

39、 from IHS-,-,-TABLE I. Size codes and dimensions. 1For each code size code there are 3 options for the PIN (see 7.1): Add a code A for cone only or a code B for cup only, use no code if for a whole bearing assembly. 2Part numbers are for reference only. Part numbers reflect the cup and cone numbers

40、used by industry and the ABMA. Some cones and cups may be used in multiple configurations and are not limited to one bearing assembly. 3These maximum fillet radii shall be cleared by the bearing corners. 4Minus value indicates load center inside cone backface. 6Size code 1Part number 2d D T T 1B C R

41、 3D 1C 1d bd aD aK factorBasic dynamic load ratings (lb.) a 4Bore Outside diameterBearing width Standout Cone width Cup width Max. shaft fillet radiusFlange Backing shoulder diameters Effective load center Cone-cup Diameter Width Shaft Housing Radial 064 469 - 453-B 2.2500 4.2500 1.0938 0.4376 1.154

42、2 0.8750 0.14 4.4640 0.2188 2.76 2.48 3.94 1.74 21800 -0.28 065 623 - 612-B 2.2500 4.7500 1.6250 0.6562 1.6250 1.2500 0.14 5.0272 0.2812 2.83 2.60 4.33 1.86 33200 -0.55 066 555S - 552-B 2.2500 4.8750 1.5000 0.5625 1.4440 1.1875 0.14 5.1210 0.2500 2.87 2.64 4.57 1.69 30700 -0.37 067 28985 - 28921-B 2

43、.3750 3.9370 1.0000 0.3750 1.0000 0.7813 0.14 4.0930 0.1563 2.87 2.64 3.86 1.37 17200 -0.10 068 65237 - 65500-B 2.3750 5.0000 1.7500 0.6563 1.7500 1.3750 0.14 5.2772 0.2813 3.23 2.79 4.72 1.20 33300 -0.37 069 39250 - 39412-B 2.5000 4.1250 0.8438 0.4063 0.8661 0.6250 0.08 4.3084 0.1875 2.87 2.72 4.02

44、 1.51 15800 -0.06 070 29585 - 29520-B 2.5000 4.2500 1.0000 0.4063 1.0000 0.7500 0.14 4.4022 0.1563 3.03 2.80 4.13 1.27 14200 -0.03 071 390A - 394A-B 2.5000 4.3307 0.8661 0.3120 0.8660 0.7411 0.06 4.5147 0.1870 2.87 2.76 4.17 1.45 16200 -0.03 072 29585 - 29521-B 2.5000 4.3307 1.0000 0.4063 1.0000 0.7

45、500 0.14 4.4803 0.1563 3.03 2.80 4.13 1.27 14200 -0.03 073 3984 - 3920-B 2.5000 4.8125 1.1875 0.4375 1.1830 0.9375 0.14 4.6210 0.1875 3.03 2.80 4.25 1.45 22400 -0.18 074 5595 - 5535-B 2.5938 4.8125 1.7188 0.5313 1.7230 1.4375 0.14 5.0625 0.2500 3.27 3.03 4.65 1.27 14200 -0.48 075 29590 - 29520-B 2.6

46、250 4.2500 1.0000 0.4063 1.0000 0.7500 0.14 4.4022 0.1563 3.15 2.87 4.13 1.27 14200 -0.03 076 395A - 394A-B 2.6250 4.3307 0.8661 0.3120 0.8660 0.7411 0.03 4.5147 0.1870 2.87 2.87 4.17 1.45 16200 -0.03 077 395-S - 394A-B 2.6250 4.3307 0.8661 0.3120 0.8660 0.7411 0.14 4.5147 0.1870 3.11 2.87 4.17 1.45

47、 16200 -0.03 078 29590 - 29521-B 2.6250 4.3307 1.0000 0.4063 1.0000 0.7500 0.14 4.4803 0.1563 3.15 2.87 4.13 1.27 14200 -0.03 079 3984 - 3920-B 2.6250 4.4375 1.1875 0.4375 1.1830 0.9375 0.14 4.6210 0.1875 3.15 2.91 4.25 1.45 22400 -0.18 080 39590 - 39520-B 2.6250 4.4375 1.1875 0.4688 1.1875 0.9375 0

48、.14 4.6523 0.2188 3.15 2.91 4.33 1.72 27000 -0.26 081 641 - 632-B 2.6250 5.3750 1.6250 0.6560 1.6250 1.2500 0.14 5.6520 0.2810 3.27 3.03 4.92 1.61 37400 -0.44 082 399A - 394A-B 2.6875 4.3307 0.8661 0.3120 0.8660 0.7411 0.09 4.5147 0.1870 3.07 2.91 4.17 1.45 16200 -0.03 083 560-S - 552-B 2.6875 4.875

49、0 1.5000 0.5625 1.1440 1.1875 0.14 5.1210 0.2500 3.27 2.99 4.57 1.69 30.700 -0.37 084 H715343 - H715310-B 2.6875 5.5000 1.8125 0.6875 1.8125 1.4375 0.14 6.0000 0.3125 3.54 3.31 5.31 1.24 43000 -0.34 A-A-59650B Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TABLE I. Size codes and dimensions. 1For each code size code there are 3 options for the PIN (see 7.1): Add a code A