ImageVerifierCode 换一换
格式:PDF , 页数:8 ,大小:62.11KB ,
资源ID:687649      下载积分:10000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-687649.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(DLA A-A-59658 B-2011 BEARINGS ROLLER TAPERED DOUBLE ROW STRAIGHT BORE TWO SINGLE CONES WITH CONTACTING FRONT FACES SLOTTED AND CHAMFERED FOR LUBRICATION ONE DOUBLE CUP WITH LUBRICA.pdf)为本站会员(李朗)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

DLA A-A-59658 B-2011 BEARINGS ROLLER TAPERED DOUBLE ROW STRAIGHT BORE TWO SINGLE CONES WITH CONTACTING FRONT FACES SLOTTED AND CHAMFERED FOR LUBRICATION ONE DOUBLE CUP WITH LUBRICA.pdf

1、Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any data that may improve this document should be sent to: STDZNMGTdla.mil or DLA Aviation VEB, 8000 Jefferson Davis Highway, Richmond, VA 23297-5616. Since contact information can change, you may want to verify the

2、 currency of this address information using the ASSIST database at https:/assist.daps.dla.mil/. FSC 3110 INCH-POUND A-A-59658B 8 September 2011 SUPERSEDING A-A-59658A 22 May 2006 COMMERCIAL ITEM DESCRIPTION BEARINGS, ROLLER, TAPERED, DOUBLE ROW, STRAIGHT BORE, TWO SINGLE CONES WITH CONTACTING FRONT

3、FACES SLOTTED AND CHAMFERED FOR LUBRICATION, ONE DOUBLE CUP WITH LUBRICATION HOLES AND GROOVE (TYPE TNASW) The General Services Administration has authorized the use of this commercial item description for all federal agencies. 1. SCOPE. This commercial item description (CID) covers government acqui

4、sition requirements for complete (cone with rollers and cup) double row, tapered, roller bearings with straight bore, two single cones with contacting front faces slotted and chamfered for lubrication, one double cup with lubrication holes and groove (type TNASW) for general purpose use. These beari

5、ngs are not intended for use in special precision applications such as on aircraft, precision ordnance, or submarine equipment. 2. CLASSIFICATION. The roller bearings shall be of one type (TNASW) and classified by the size codes listed in table I. The column headings in table I refer to bearing char

6、acteristics defined in figure 1. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59658B 2 FIGURE 1. Bearing characteristics. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-3A-A-59658B TABLE I. Si

7、ze codes and dimensions. Size code Part number 1d D T B R 2r 2d aD aK factor Basic dynamic load ratings (lb.) Bore Outside diameter Overall width Overall cup width Max. shaft fillet radius Max. housing fillet radius Recommended shoulder diameter Cone-cup Shaft Housing Two row radial 001 NA26118-SW -

8、 26284D 1.1806 2.8338 1.6835 1.4375 0.06 0.03 1.56 2.56 1.62 16300 002 NA3780-SW - 3729D 2.0000 3.6718 2.5625 2.0625 0.14 0.03 2.52 3.46 1.73 33700 003 NA455-SW - 452D 2.0000 4.2500 2.5625 2.1250 0.14 0.03 2.56 3.94 1.74 37400 004 NA558-SW - 552D 2.3750 4.8750 3.1250 2.5000 0.14 0.06 2.99 4.53 1.69

9、52600 005 NA643-SW - 632D 2.7500 5.3750 3.7500 3.0000 0.14 0.06 3.39 4.92 1.61 64200 006 NA484-SW - 472D 2.7559 4.7244 2.5626 2.1250 0.14 0.03 3.27 4.49 1.52 39600 007 NA759-SW - 752D 3.5000 6.3750 4.1250 3.3750 0.14 0.06 4.17 5.91 1.71 89800 008 NA691-SW - 672D 4.0000 6.6250 3.6250 2.7500 0.14 0.03

10、 4.65 6.30 1.24 68200 009 NA67791-SW - 67720CD 7.0000 9.7500 4.0625 3.3125 0.14 0.03 7.64 9.95 1.33 66800 1Part numbers are for reference only. Part numbers reflect the cup and cone numbers used by industry and the ABMA. Some cones and cups may be used in multiple configurations and are not limited

11、to one bearing assembly. 2These maximum fillet radii shall be cleared by the bearing corners. 3Minus value indicates load center inside cone backface. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59658B 4 3. SALIENT CHARACTERISTICS 3.1 Dimensi

12、ons. Bearing dimensions (and dynamic load ratings, see 3.4) shall conform to the requirements specified in table I for each of the bearing part numbers. The listed dimensions conform to the requirements specified in American Bearing Manufacturers Association (ABMA) Standard 19.2, “Tapered Roller Bea

13、rings - Radial Inch Design“. The bearing size shall be specified in the acquisition order (see 7.3(b). For any unlisted bearing size codes, the associated dimensional and dynamic load rating requirements should also be specified in the acquisition order. 3.2 Materials. 3.2.1 Cones (inner rings), cup

14、s (outer rings), and rollers. The bearing cones, cups, and rollers shall be made of case carburized or through-hardened steel produced in accordance with the ASTM International (ASTM) A295/A295M, “Standard Specification for High-Carbon Anti-Friction Bearing Steel“, or ASTM A534, “Standard Specificat

15、ion for Carburizing Steels for Anti-Friction Bearings“. The steel shall show a fine fracture grain size in accordance with ASTM E112, “Standard Test Methods for Determining Average Grain Size“. Material hardness shall be no less than Rockwell hardness number of 58 on Rockwell C scale (HRC) and no mo

16、re than 64 HRC as defined in ASTM E18, “Standard Test Methods for Rockwell Hardness of Metallic Materials“. 3.2.2 Cage. The bearing cage material shall be impervious to deterioration from any lubricant, preservative, solvent, or other chemical substance expected to contact the bearing during normal

17、use or storage. Similarly, the material shall not cause any chemical deterioration of any other bearing component. The cages shall be made from carbon steel (one piece stamped). Materials shall operate from -65 to 230 F (-53.9 to 110 C). 3.3 Tolerance class. The tolerance limits for bearings shall c

18、onform to tolerance class 4 as tabulated in ABMA Standard 19.2. Allowable tolerances for bearing components and assembled bearings are listed in tables II through V. TABLE II. Cone bore tolerance. Cone bore (d) Size range Tolerance Over Inclusive Plus Minus 0.0000 3.0000 5 0 3.0000 6.0000 10 0 Note:

19、 Allowable tolerances are in 0.0001 inch. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59658B 5 TABLE III. Cup diameter tolerance. Cup diameter (D) Size range Tolerance Over Inclusive Plus Minus 0.0000 12.0000 10 0 12.0000 24.0000 20 0 Note: A

20、llowable tolerances are in 0.0001 inch. TABLE IV. Bearing width tolerance. Bearing width (T) Bore size range Tolerance Over Inclusive Plus Minus 0.0000 5.0000 100 0 5.0000 12.0000 300 0 Note: Allowable tolerances are in 0.0001 inch. TABLE V. Assembled bearing tolerance. Assembled bearing maximum rad

21、ial runout Cup outside diameter (D) Tolerance Over Inclusive 0.0000 24.0000 20 Note: Allowable tolerances are in 0.0001 inch. 3.4 Dynamic load rating. The bearing dynamic load rating shall conform to the requirements specified in table I for each bearing size code. The listed ratings conform to the

22、requirements specified in ABMA Standard 11, “Load Ratings and Fatigue Life for Roller Bearings“. 3.5 Lubrication. The bearings shall be furnished without lubrication. 3.6 Contact angle. All bearings are normal angle bearings having a contact angle between 10 and 19 degrees. The contact angle is the

23、angle between the line of action of the roller load and a plane perpendicular to the bearing axis. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59658B 6 4. REGULATORY REQUIREMENTS 4.1 Recovered materials. The offeror/contractor is encouraged t

24、o use recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 4.2 Foreign acquisition restrictions. Unless otherwise indicated in the solicitation and resulting contract, the foreign acquisition restrictions in Section 2

25、52.225, Clause 252.225.7016, of the Defense Federal Acquisition Regulation Supplement (DFARS) apply to products described by this CID. 5. PRODUCT CONFORMANCE PROVISIONS 5.1 Product conformance. The products provided shall meet the salient characteristics of this CID, conform to the producers own dra

26、wings, specifications, standards, and quality assurance practices, and be the same product offered for sale in the commercial marketplace. The government reserves the right to require proof of such conformance. 5.2 Market acceptability. The products offered must have been previously sold either to t

27、he government or on the commercial market. 6. PACKAGING 6.1 Preservation, packing, and marking. Unless otherwise specified in the acquisition order, the bearings shall be preserved, packaged, and marked in accordance with MIL-DTL-197, “Packaging of Bearings, Associated Parts and Subassemblies“ (see

28、7.3(c). 7. NOTES 7.1 Part or identification number (PIN). The following PIN procedure is for government purposes and does not constitute a requirement for the contractor. AA59658 - 003 Example of reference part number Size code (see table I) CID Number AA59658 - 003 indicates: Bearing bore 2.0000 in

29、ches; outside diameter 4.2500 inches; width 2.5626 inches. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59658B 7 7.2 Sources of documents. 7.2.1 DFARS and FAR. Copies of DFARS and FAR may be obtained from the Superintendent of Documents, P.O.

30、Box 371954, Pittsburgh, PA 15250-7954. Electronic copies of DFARS may be obtained from http:/www.acq.osd.mil/dpap/dars/dfarspgi/current/index.html. Electronic copies of FAR may be obtained from https:/www.acquisition.gov/far/. 7.2.2 Military specifications. Copies of military specifications may be o

31、btained from Standardization Documents Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094. Electronic copies may be obtained from https:/assist.daps.dla.mil/. 7.2.3 ABMA standards. Copies of ABMA standards may be obtained from the American Bearing Manufacturers Association, 202

32、5 M Street NW, Suite 800, Washington, DC 20036. Electronic copies may be obtained from http:/www.abma-dc.org/. 7.2.4 ASTM standards. Copies of ASTM standards may be obtained from ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959. Electronic copies may be obta

33、ined from http:/www.astm.org/. 7.3 Ordering data. The acquisition order should specify the following information: a. CID document number, revision, and CID PIN. b. Bearing size (with dimension/load requirements if size is unlisted) (see 3.1). c. Preservation, packaging, and marking requirements (see

34、 6.1). 7.4 Cross-reference information. Table VI relates the original specification slant sheets to the replacement CIDs. TABLE VI. Federal specification to CID cross-reference. FF-B-187B specification sheets Replacement CID numbers ABMA types 1 A-A-59649 TS 2 A-A-59650 TSF 3 A-A-59651 TSS 4 A-A-596

35、52 TSSF 5 A-A-59653 TDI and TDIS 6 A-A-59654 TDO 7 A-A-59655 TDOS 8 A-A-59656 TNA (normal angle) 9 A-A-59657 TNAS (steep angle) 10 A-A-59658 TNASW 11 A-A-59659 TNASWE Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59658B 8 7.5 Subject term (key

36、word) listing. Bore Cone Cup Load Width MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY:Custodians: GSA - FAS Army - AR Navy - MC Air Force - 99 DLA - GS Review Activities: Navy - OS Air Force - 84 Preparing Activity: DLA - GS4 (Project 3110-2011-027) NOTE: The activities listed above were in

37、terested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST database at https:/assist.daps.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1