DLA A-A-59688 D-2012 FUSE CARTRIDGE INSTRUMENT TYPE 5 MM X 20 MM GENERAL REQUIREMENTS FOR.pdf

1、Beneficial comments, recommendations, additions, deletions, clarifications, etc., and any data which may improve this document should be sent to: DLA Land and Maritime, ATTN: VAT, P.O. Box 3990, Columbus, OH 43218-3990, or email mailto:CircuitProtectdla.mil. Since contact information can change you

2、may want to verify the currency of the address information using the ASSIST Online database at https:/assist.dla.mil. AMSC N/A FSC 5920 METRIC A-A-59688D 15 December 2012 SUPERSEDING A-A-59688C 3 May 2007 COMMERCIAL ITEM DESCRIPTION FUSE, CARTRIDGE, INSTRUMENT TYPE, 5 MM X 20 MM, GENERAL REQUIREMENT

3、S FOR The General Services Administration has authorized the use of this commercial item description for all federal agencies. 1. SCOPE. This commercial item description (CID) covers the general requirements for 5 mm x 20 mm, instrument type, fuse cartridges. Requirements for specific fuses are cove

4、red in the individual CID specification sheets. Fuses covered by this CID are intended for commercial/industrial applications. 2. CLASSIFICATION/PART OR IDENTIFICATION NUMBER (PIN). This CID uses a classification system which is included in the PIN as shown in the following example (see 7.1). AA5968

5、8 /01 - 001 A Abbreviated CID number Applicable CID specification sheet (two digits) Dash number (see applicable CID specification sheet) Configuration (see figure 1 of applicable CID specification sheet) 3. SALIENT CHARACTERISTICS. 3.1 Interface and physical dimensions. Fuses supplied to this CID s

6、hall be as specified on the applicable CID specification sheet. 3.2 CID specification sheet. The family of fuses shall be in accordance with the requirements specified herein and the applicable CID specification sheet. In the event of a conflict between this general CID and the applicable CID specif

7、ication sheet, the latter shall govern. 3.3 Marking. Fuses supplied to this CID shall be marked with the manufacturers (MFRs) standard commercial PIN. (NOTE: The part number marked on the unit pack shall be the CID PIN.) 3.4 Recycled, recovered, or environmentally preferable materials. Recycled, rec

8、overed, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs.Provided by IHSNot for ResaleNo reproduction or networking p

9、ermitted without license from IHS-,-,-A-A-59688D 2 3.5 Workmanship. Fuses shall be processed in such a manner as to be uniform in quality and shall be free from other defects that will affect life, serviceability, or appearance. 4. REGULATORY REQUIREMENTS. The offeror/contractor is encouraged to use

10、 recovered materials to the maximum extent practicable, in accordance with 23.403 of the Federal Acquisition Regulation (FAR). 5. PRODUCT CONFORMANCE PROVISIONS. 5.1 Product conformance. The products provided shall meet the salient characteristics of this CID, conform to the producers own drawings,

11、specifications, standards, and quality assurance practices, and be the same product offered for sale in the commercial market. The Government reserves the right to require proof of such conformance. 5.2 Market acceptance. The following market acceptance criteria are necessary to document the quality

12、 of the product to be provided under this CID: a. The company producing the item must have been producing a product meeting the requirements of this CID for at least 2 years. b. The company producing the item must have sold 1,000 units meeting this CID in the commercial marketplace over the past 2 y

13、ears. 6. PACKAGING. Preservation, packing, and marking shall be as specified in the contract or order. 7. NOTES. 7.1 PIN. The PIN should be used for Government purposes to buy commercial products to this CID. See section 2 for PIN format example. 7.2 Environmentally preferable materials. Environment

14、ally preferable materials should be used to the maximum extent possible to meet the requirements of this specification. As of the dating of this document, the U.S. Environmental Protection Agency (EPA) is focusing efforts on reducing 31 priority chemicals. The list of chemicals and additional inform

15、ation is available on their website http:/www.epa.gov/osw/hazard/wastemin/priority.htm. Included in the EPA list of 31 priority chemicals are cadmium, lead, and mercury. Use of these materials should be minimized or eliminated unless needed to meet the requirements specified herein (see Section 3).

16、7.3 Commercial and Government Entity (CAGE) code. For ordering purposes, inventory control, and submission of these fuses to DLA Land and Maritime under the Military Parts control Advisory Group (MPCAG) evaluation program, CAGE code 58536 should be used. 7.4 Source of documents. FEDERAL REGULATIONS

17、FAR - Federal Acquisition Regulations (FAR). (Copies of this document are available online at https:/www.acquisition.gov/comp/far/index.html or from the U.S. Government Printing Office, 732 North Capital Street, NW, Washington D.C. 20401-0001.) 7.5 Ordering data. The contract or order should specify

18、 the following: a. CID document number, revision, and CID PIN. b. Product conformance provisions. c. Packaging requirements. 7.6 Government users. To acquire information on obtaining these fuse cartridges from the Government inventory system, contact DLA Land and Maritime, ATTN: DLA Land and Maritim

19、e-FMX, P.O. Box 3990, Columbus, OH 43218-3990, or telephone (614) 692-3677. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59688D 3 7.7 Changes from previous issue. Marginal notations are not used in this revision to identify changes with respec

20、t to the previous issue due to the extensiveness of the changes. MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: GSA - FAS Custodians: Navy - EC Preparing activity: DLA - CC DLA-CC Project 5920-2012-050 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-