DLA A-A-59744 A-2013 CHOKE COMMON MODE SURFACE MOUNT.pdf

1、Beneficial comments recommendations, additions, deletions, clarifications, etc., and any data which may improve this document should be addressed to: DLA Land and Maritime, Columbus, ATTN: VAT, P.O. Box 3990, Columbus OH 43218-3990, or email (transformersdla.mil ). Since contact information can chan

2、ge you may want to verify the currency of the address information using the ASSIST Online database at https:/assist.dla.mil. AMSC N/A FSC 5950 A-A-59744A 5 December 2013 SUPERSEDING A-A-59744 23 September 2002 COMMERCIAL ITEM DESCRIPTION CHOKE, COMMON MODE, SURFACE MOUNT The General Services Adminis

3、tration has authorized the use of this commercial item description (CID) for all federal agencies. 1. SCOPE. This CID covers the general requirements for a Choke. Chokes covered by this CID are intended for commercial/industrial applications. 2. CLASSIFICATION/PART OR IDENTIFICATION NUMBER (PIN). Th

4、is CID uses a classification system which is included in the Part Identification Number (PIN) as shown in the following example (see 7.1). AA59744 - 001 L CID number Dash number (see table I) (Optional) Termination finish (see table II) 3. SALIENT CHARACTERISTICS. 3.1 Interface and physical dimensio

5、ns. Chokes supplied to this CID shall be as specified herein. (see figure 1and figure 2). 3.2. Electrical characteristics. The electrical characteristics shall be as specified in table I. 3.3. Insertion loss (dB) common mode/differential mode. Insertion loss shall be as specified in figure 3. 3.4. I

6、mpedance vs. Frequency. Impedance verses frequency shall be as specified in figure 4. 3.5 Weight. The weight shall be 0.297 gram maximum. 3.6 Operating temperature range. The operating temperature range is 40C to +85C. 3.7 Temperature rise. DC current rating for a 15C rise. 3.8 Altitude. The maximum

7、 altitude is 70,000 feet. 3.9 Marking. Chokes supplied to this CID shall be marked with the manufacturers standard commercial PIN. 3.10 Pure tin. The use of pure tin, as an underplate or final finish is prohibited both internally and externally. Tin content of transformer components and solder shall

8、 not exceed 97 percent, by mass. Tin shall be alloyed with a minimum of 3 percent lead, by mass. INCH-POUNDProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59744A 2 3.11 Recycled, recovered, or environmentally preferable materials. Recycled, recov

9、ered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.12 Workmanship. Coils shall be processed in such a manner a

10、s to be uniform in quality and shall be free from other defects that will affect life, serviceability, or appearance. A max B max C max D ref E ref F ref G min H ref 0.231 (5.87) 0.196 (4.97) 0.150 (3.81) 0.107 (2.72) 0.100 (2.54) .178 (4.52) 0.04 (1.02) 0.03 (0.76) NOTES: 1. Dimensions are in Inche

11、s. 2. Metric equivalents, in parenthesis, are listed for general information only. FIGURE 1. Configuration and dimensions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59744A 3 FIGURE 2. Schematic diagram. Common mode/Differential mode dB 100

12、MHz 200 MHz 400 MHz 500 MHz 9.04/0.19 13.66/0.94 17.75/1.79 17.11/2.09 FIGURE 3. Insertion loss graph/table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59744A 4 FIGURE 4 TABLE I. Electrical characteristics. CID dash number AA59744- Inductanc

13、e Min (H) DCR Max (Ohms) 1/ IDC Max (A) 001 0.22 100 kHz .105 1.5 1/ DC current rating for a 15C rise. TABLE II. Termination finish. Code Termination finishLeave blank L Tin-lead RoHS compliant, Gold over nickel over moly-manganese. 4. REGULATORY REQUIREMENTS. The offeror/contractor is encouraged to

14、 use recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59744A 5 5. PRODUCT CONFORMANCE PROVISIONS 5.1 Product co

15、nformance. The products provided shall meet the salient characteristics of this CID, conform to the producers own drawings, specifications, standards, and quality assurance practices, and be the same product offered for sale in the commercial market. The Government reserves the right to require proo

16、f of such conformance. 6. PACKAGING. Preservation, packing, and marking shall be as specified in the contract or order. 7. NOTES. 7.1 PIN. The PIN should be used for Government purposes to buy commercial products to this CID. See section 2 for PIN format example. 7.2 Environmentally preferable mater

17、ial. Environmentally preferable materials should be used to the maximum extent possible to meet the requirements of this specification. As of the dating of this document, the U.S. Environmentally Protection Agency (EPA) is focusing efforts on reducing 31 priority chemicals. The list of chemicals is

18、available on their website at http:/www.epa.gov/epaoswer/hazwaste/minimize/chemlist.htm. Further information is available at the following EPA site: http:/www.epa.gov/epaoswer/hazwaste/minimize/. Included in the EPA list of 31 priority chemicals are cadmium, lead, and mercury. Use of the materials o

19、n the list should be minimized or eliminated unless needed to meet the requirements specified herein (see Section 3). 7.3 Commercial and Government Entity (CAGE) code. For ordering purposes, inventory control, and submission of these inductors to DSCC under the Military Parts Control Advisory Group

20、(MPCAG) evaluation program, CAGE code 58536 should be used. 7.4 Source of documents. FEDERAL REGULATIONS FAR - Federal Acquisition Regulations (FAR) (Copies of these documents are available online at www.acquisition.gov/comp/far/index.html or from the U.S. Government Printing Office, 732 North Capit

21、al Street, NW, Washington D.C. 20401.) 7.5 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker growth problems after manufacture. Tin whiskers may occur anytime from a day to years after manufacture and can develop under typical operating

22、conditions, on products that use such materials. Conformal coatings applied over top of a whisker-prone surface will not prevent the formation of tin whiskers. Alloys of 3 percent lead, by mass, have shown to inhibit the growth of tin whiskers. For additional information on this matter, refer to AST

23、M-B545 (Standard Specification for Electrodeposited Coatings of Tin). 7.6 Ordering data. The contract or order should specify the following: a. CID document number, revision, and CID PIN. b. Product conformance provisions. c. Packaging requirements. 7.7 Commercial products. As part of the market ana

24、lysis and research effort, this CID was coordinated with the following manufacturer of commercial products. At the time of CID preparation and coordination, this manufacturer was known to have commercial products that would meet the requirements of this CID. (NOTE: This information should not be con

25、sidered as a list of approved manufacturer or be used to restrict procurement to only the manufacturer shown.) MFRs CAGE MFRs name and address 02113 Coilcraft Inc 1102 Silver Lake Road Cary, Illinois 60013-1658 Phone number (847) 639-2361 Uniform Resource Locator (URL): Provided by IHSNot for Resal

26、eNo reproduction or networking permitted without license from IHS-,-,-A-A-59744A 6 7.8 Part number (P/N) supersession data. This CID supersedes the following manufacturers P/Ns as shown. This information is being provided to assist in reducing proliferation in the government inventory system. TABLE

27、III. P/N supersession data. 1/ CID dash number (see table I) AA59744- Vendor commercial PIN 2/ CAGE 99800 001* CM1394L*1/ When “*“ is used for coded values, its the contractors responsibility to select those options allowed by the CID. 2/ The manufacturers P/N shall not be used for procurement to th

28、e requirements of this CID. At the time of preparation of this CID, the aforementioned commercial products were reviewed and could be replaced by the CID P/N shown. 7.9 Government users. To acquire information on obtaining these coils from the Government inventory system, contact DLA Land and Mariti

29、me ATTN: DSCC-FMTC, Post Office Box 3990, Columbus, OH 43218-3990, or telephone (614) 692-7727. 7.10 Changes from previous issue. The margins of this CID are marked with asterisks to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assu

30、mes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. MILITARY INTERESTS: CIVIL AGENCY CO

31、ORDINATING ACTIVITY: GSA - 7FXE Custodians: Navy - EC Preparing Activity: DLA - CC DLA - CC Project 5950-2013-022 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-