DLA A-A-59789 12 A-2012 HOLDER ELECTRICAL CARD WEDGE RETAINERS 5 PIECE FOR COLD PLATE APPLICATIONS 375 X 375 INCH BODY SIZE WITH TWO MOUNTING HOLES AND VISUAL LOCK INDICATION SCREW.pdf

1、INCHPOUND AA59789/12A 12 June 2012 SUPERSEDING AA59789/12 4 May 2007 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET HOLDER, ELECTRICAL CARD, WEDGE RETAINERS, 5 PIECE, FOR COLD PLATE APPLICATIONS, .375 X .375 INCH BODY SIZE, WITH TWO MOUNTING HOLES AND VISUAL LOCK INDICATION, SCREW ACTUATED The Gene

2、ral Services Administration has authorized the use of this commercial item description for all federal agencies. The complete requirements for procuring 5 piece card holders described herein shall consist of this document and the latest issue in effect of AA59789. CLASSIFICATION/PART IDENTIFICATION

3、NUMBER (PIN). This commercial item description (CID) specification sheet uses a classification system which is included in the Part Identification Number (PIN) as shown in the following example (see notes herein). AA59789 CID number /12 Applicable CID sheet * Configuration (see table I) * Finish * *

4、 Length (see table II) * Mounting Example: AA59789/12AB60S is the PIN for a black anodized with dry film lubricant finished, 6.0 inches (121.9 mm) long card holder. The card holder also features two tapped mounting holes for use with 256 UNC 2B fasteners and has visual lock indication. SALIENT CHARA

5、CTERISTICS. Performance. Card holders shall hold the circuit card firmly in its installed position and prevent loosening or movement as a result of shock and vibration. It shall also provide a thermal transfer path from the circuit card assembly to the cold plate. Interface and physical dimensions.

6、The card holders supplied to this CID specification sheet shall be as specified herein and meet the general requirements specified in CID AA59789. The card holders shall have a visual indicator to show when the assembly is in its relaxed (unlocked) and expanded (locked) state. Material. Unless other

7、wise specified herein, the card holder materials shall be as specified in AA59789. Actuating screw hex drive socket. The across flats dimension for hex drive socket shall be .140 inch (3.60 mm) for mounting options “R“, “S“, and “V“ and .118 inch (3.0 mm) for mounting option “Y“. Cold plate slot wid

8、th. The recommend cold plate slot width to accommodate the circuit card assembly with attached card holder is .425 inch (10.80 mm) plus the thickness of the printed board of the circuit card assembly (see AA59789). Installation torque. The recommended nominal installation torque is as follows: 16 in

9、ch-pounds (1.8 N-m) for assemblies of configuration “A“ and “F“ and 20 inch-pounds (2.3 N-m) for assemblies of configurations “J“ and “N“. AMSC N/A FSC 5998 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59789/12A 2 Configuration. The configuratio

10、n of a card holder shall be as specified in table I. The details of a particular configuration consist of those on figures 1 and 2, and may include those on figures 3 or 4. TABLE I. Configuration. Configuration Applicable figures Hardware options A 1 and 2 No added options F 1, 2 and 3 Lockwasher an

11、d flat washer N 1, 2 and 4 Screw self-locking element J 1, 2, 3 and 4 Lockwasher, flat washer, and screw self-locking element Inches mm Inches mm Inches mm .24 .30 6.1 7.6 .330 .375 8.38 9.26 .470 .500 11.94 12.7 FIGURE 1. Relaxed and expanded dimensions. Provided by IHSNot for ResaleNo reproduction

12、 or networking permitted without license from IHS-,-,-AA59789/12A 3 NOTES: 1. Dimensions are in inches. Millimeters are given for general information only. 2. Unless otherwise specified, tolerances are .02 inch (0.51 mm) for two place decimals and .010 inch (0.25 mm) for three place decimals. 3. Con

13、figuration shown uses captive nut on rear wedge. Alternate design using threaded insert shall be acceptable. 4. The across flats dimension for actuating screw hex drive socket shall be .140 inch (3.60 mm) or .118 inch (3.0 mm) for the corresponding mounting option (see hex drive socket details). FIG

14、URE 1. Relaxed and expanded dimensions Continued. Visual lock indicator (see figure 2). Card holders shall have a visual indicator to show when the card holder is in its relaxed (unlocked) state. When the card holder is in the relaxed (unlocked) state, the end of the actuating screw shall display a

15、red band on the side of the screw. When the actuating screw on the card holder has been tightened so that the assembly is in the expanded (locked) position, this red band shall be concealed. FIGURE 2. Visual lock indicator. Finish. The finish designator shall be as specified in AA59789. The finishes

16、 available for this CID specification sheet are as follows: “B“ (black anodize), “E“ (electroless nickel), “H“ (hard black anodize), or “R“ (clear chemical film). Length, expanded, and relaxed dimensions. The length designator shall be as specified in AA59789 and the lengths available for this CID s

17、pecification sheet are listed in table II. The length, expanded, and relaxed dimensions shall be as specified on figure 1. TABLE II. Additional assembly dimensions (see figure 1). 1/ PIN length designator Dimension “Length“ .02 (0.5) Dimension “M“ .01 (0.3) 50 4.80 (121.9) 1.00 (25.4) 55 5.30 (134.6

18、) 1.00 (25.4) 60 5.80 (147.3) 1.00 (25.4) 65 6.30 (160.0) 1.00 (25.4) 1/ Dimensions are in inches. Millimeters, in parenthesis, are given for general information only. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59789/12A 4 Mounting. The mounti

19、ng designators shall be as specified in AA59789. The mounting options available for this CID specification sheet are as follows: “R“ (rivet mount using countersunk holes), “S“ (tapped 256 holes), “V“ (tapped 440 holes), or “Y“ (tapped metric M3 x 0.5 holes) shall be as specified in AA59789. See figu

20、re 1 and table I for mounting hole spacing requirements. Card holders using mounting option “R“ may be shipped unassembled. Rivet mount holes. The holes used for rivet mounting shall be .134/.139 inch (3.40/3.53 mm) diameter, countersunk 100 degrees by .190/.200 inch (4.83/5.08 mm) diameter through

21、holes with a counterbore of .190/.200 inch (4.83/5.08 mm) diameter by .300 inch (7.62 mm) deep. Rivets. This card holder uses rivet style B as specified in AA59789 when rivet mounting is used. Configuration hardware options. Card holders can have the following hardware options: no added hardware, lo

22、ckwasher and flat washer, screw self-locking element, or a combination of both lockwasher and flat washer and screw self-locking element. See table I for the correct PIN configuration identifier. Card holders requiring no added hardware options shall include configuration identifier “A“ in the PIN (

23、see table I, classification, and notes section herein). Lockwasher and flat washer (see figure 3). A lockwasher and flat washer located under the screw head will provide for additional resistance to loosening from shock and vibration. Card holders requiring a lockwasher and flat washer shall include

24、 configuration identifier “F“ in the PIN (see table I, classification, and notes section herein). FIGURE 3. Lockwasher and flat washer details. Screw self-locking element (see figure 4). The use of a screw self-locking element will provide prevailing torque for resistance to loosening from shock vib

25、ration. The screw self-locking element shall be in accordance with AA59789. Card holders requiring a screw self-locking element shall include configuration identifier “N“ in the PIN (see table I, classification, and notes section herein). FIGURE 4. Screw self-locking element details. Lockwasher, fla

26、t washer, and screw self-locking element. Card holders requiring a lockwasher, flat washer, and screw self-locking element option shall include configuration identifier “J“ in the PIN (see table I, classification, and notes section herein). Provided by IHSNot for ResaleNo reproduction or networking

27、permitted without license from IHS-,-,-AA59789/12A 5 NOTES. PIN. The PIN should be used for Government purposes to buy commercial products to this CID specification sheet. See the classification section for PIN format example. Source of documents. Commercial Item Description AA59789 Holder, Electric

28、al Card, Wedge Retainers, 5 Piece, For Cold Plate Applications, General Requirements For. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or https:/assist.daps.dla.mil/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philad

29、elphia, PA 191115094.) Ordering data. Ordering data shall be as specified in AA59789. Commercial products. As part of the market analysis and research effort, this CID specification sheet was coordinated with the following manufacturers of commercial products. At the time of CID specification sheet

30、preparation and coordination, these manufacturers were known to have commercial products that would meet the requirements of this CID specification sheet. (NOTE: This information should not be considered as a list of approved manufacturers or be used to restrict procurement to only the manufacturers

31、 shown.) Manufacturer CAGE Manufacturer name and address Manufacturer contact information 18915 Birtcher A Division of Pentair Technical Products 7328 Trade Street San Diego, CA 921213410 Telephone: (858) 7402400 Toll Free: (800) 8547086 Facsimile: (858) 6794555 URL: 5BG68 Card Locks Unlimited, Inc

32、. 2310 E. Orangethorpe Avenue Anaheim, CA 928061231 Telephone: (714) 7386194 Facsimile: (714) 4460119 E-mail: URL: Part number supersession data. These CID specification sheet PINs supersede the following manufacturers part numbers as shown in table III. The CID PINs listed in table III are only f

33、or length designator “50“. See table IV for CID PIN construction using other available lengths for this CID specification sheet. This information is being provided to assist in reducing proliferation in the Government inventory system. Provided by IHSNot for ResaleNo reproduction or networking permi

34、tted without license from IHS-,-,-AA59789/12A 6 TABLE III. Commercial part number supersession data. PIN designator AA59789/12 Vendor similar designator or type part number 1/ CAGE 18915 CAGE 5BG68 AB50V 445VI10B 5251VBA4.80T4 AB50R 445VI10BR 5251VBA4.80H AB50S 445VI10BS 5251VBA4.80T2 AB50Y 445VI10B

35、M3 5251MVBA4.80TM3 FB50V 445VI10BLF 5251VWBA4.80T4 FB50R 445VI10BLFR 5251VWBA4.80H FB50S 445VI10BLFS 5251VWBA4.80T2 FB50Y 445VI10BLFM3 5251MVWBA4.80TM3 NB50V 445VI10BL 5251VBA4.80T4L NB50R 445VI10BRL 5251VBA4.80HL NB50S 445VI10BSL 5251VBA4.80T2L NB50Y 445VI10BM3L 5251MVBA4.80TM3L JB50V 445VI10BLFL 5

36、251VWBA4.80T4L JB50R 445VI10BLFRL 5251VWBA4.80HL JB50S 445VI10BLFSL 5251VWBA4.80T2L JB50Y 445VI10BLFM3L 5251MVWBA4.80TM3L AE50V 445VI10EN 5251VEN4.80T4 AE50R 445VI10ENR 5251VEN4.80H AE50S 445VI10ENS 5251VEN4.80T2 AE50Y 445VI10ENM3 5251MVEN4.80TM3 FE50V 445VI10ENLF 5251VWEN4.80T4 FE50R 445VI10ENLFR 5

37、251VWEN4.80H FE50S 445VI10ENLFS 5251VWEN4.80T2 FE50Y 445VI10ENLFM3 5251MVWEN4.80TM3 NE50V 445VI10ENL 5251VEN4.80T4L NE50R 445VI10ENRL 5251VEN4.80HL NE50S 445VI10ENSL 5251VEN4.80T2L NE50Y 445VI10ENM3L 5251MVEN4.80TM3L See footnote at end of table. Provided by IHSNot for ResaleNo reproduction or netwo

38、rking permitted without license from IHS-,-,-AA59789/12A 7 TABLE III. Commercial part number supersession data Continued. PIN designator AA59789/12 Vendor similar designator or type part number 1/ CAGE 18915 CAGE 5BG68 JE50V 445VI10ENLFL 5251VWEN4.80T4L JE50R 445VI10ENLFRL 5251VWEN4.80HL JE50S 445VI

39、10ENLFSL 5251VWEN4.80T2L JE50Y 445VI10ENLFM3L 5251MVWEN4.80TM3L AH50V 445VI10B3 5251VBH4.80T4 AH50R 445VI10B3R 5251VBH4.80H AH50S 445VI10B3S 5251VBH4.80T2 AH50Y 445VI10B3M3 5251MVBH4.80TM3 FH50V 445VI10B3LF 5251VWBH4.80T4 FH50R 445VI10B3LFR 5251VWBH4.80H FH50S 445VI10B3LFS 5251VWBH4.80T2 FH50Y 445VI

40、10B3LFM3 5251MVWBH4.80TM3 NH50V 445VI10B3L 5251VBH4.80T4L NH50R 445VI10B3RL 5251VBH4.80HL NH50S 445VI10B3SL 5251VBH4.80T2L NH50Y 445VI10B3M3L 5251MVBH4.80TM3L JH50V 445VI10B3LFL 5251VWBH4.80T4L JH50R 445VI10B3LFRL 5251VWBH4.80HL JH50S 445VI10B3LFSL 5251VWBH4.80T2L JH50Y 445V10B3LFM3L 5251MVWBH4.80TM

41、3L AR50V 445VI10CC 5251VCC4.80T4 AR50R 445VI10CCR 5251VCC4.80H AR50S 445VI10CS 5251VCC4.80T2 AR50Y 445VI10CCM3 5251MVCC4.80TM3 FR50V 445VI10CCLF 5251VWCC4.80T4 FR50R 445VI10CCLFR 5251VWCC4.80H FR50S 445VI10CCLFS 5251VWCC4.80T2 FR50Y 445V10CCLFM3 5251MVWCC4.80TM3 See footnote at end of table. Provide

42、d by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59789/12A 8 TABLE III. Commercial part number supersession data Continued. PIN designator AA59789/12 Vendor similar designator or type part number 1/ CAGE 18915 CAGE 5BG68 NR50V 445VI10CCL 5251VCC4.80T4L NR5

43、0R 445VI10CCRL 5251VCC4.80HL NR50S 445VI10CCSL 5251VCC4.80T2L NR50Y 445VI10CCM3L 551MVCC4.80TM3L JR50V 445VI10CCLFL 5251VWCC4.80T4L JR50R 445VI10CCLFRL 5251VWCC4.80HL JR50S 445VI10CCLFSL 5251VWCC4.80T2L JR50Y 445VI10CCLFM3L 5251MVWCC4.80TM3L 1/ The manufacturers part number shall not be used for pro

44、curement to the requirements of this CID specification sheet. At the time of preparation of this CID specification sheet, the aforementioned commercial products were reviewed and could be replaced by the CID PIN shown. For actual part marking requirements, see the marking paragraph in AA59789. TABLE

45、 IV. Example of PIN with available length designators. PIN designator AA59789/12 Vendor similar designator or type part number 1/ 2/ CAGE 18915 CAGE 5BG68 AB50S 445VI10BS VA2514.80T2 AB55S 445VI11BS VA2515.30T2 AB60S 445VI12BS VA2515.80T2 AB65S 445VI13BS VA2516.30T2 1/ The manufacturers part number

46、shall not be used for procurement to the requirements of this CID specification sheet. At the time of preparation of this CID specification sheet, the aforementioned commercial products were reviewed and could be replaced by the CID PIN shown. For actual part marking requirements, see the marking pa

47、ragraph in AA59789. 2/ Other lengths are available on request. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59789/12A 9 MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: Custodians: GSA FAS Army CR Navy EC Preparing activity: Air Force 85 DLA CC DLA CC Project 59982012012 Review activity: Air Force 99 NOTE: The activities listed above were interested in this documen