DLA A-A-59789 16 A-2013 HOLDER ELECTRICAL CARD WEDGE RETAINERS 5 PIECE FOR COLD PLATE APPLICATIONS 365 X 375 INCH BODY SIZE WITH CAPTIVE REAR WEDGE AND VISUAL LOCK INDICATION SCREW.pdf

1、INCH-POUND AA59789/16A 16 January 2013 Superseding AA59789/16 10 May 2008 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET HOLDER, ELECTRICAL CARD, WEDGE RETAINERS, 5 PIECE, FOR COLD PLATE APPLICATIONS, .365 X .375 INCH BODY SIZE, WITH CAPTIVE REAR WEDGE AND VISUAL LOCK INDICATION, SCREW ACTUATED The

2、 General Services Administration has authorized the use of this commercial item description for all federal agencies. The complete requirements for procuring 5 piece card holders described herein shall consist of this document and the latest issue in effect of AA59789. CLASSIFICATION/PART IDENTIFICA

3、TION NUMBER (PIN). This commercial item description (CID) specification sheet uses a classification system which is included in the Part Identification Number (PIN) as shown in the following example (see notes herein). AA59789 CID number /16 Applicable CID sheet * Configuration (see table I) * Finis

4、h * * Length (see table II) * Mounting Example: AA59789/16LE40R is the PIN for a nickel finished, 3.8 inch (97 mm) long card holder with a visual lock indication feature. The card holder also features two counterbored holes for use with rivets and a screw self locking element for added resistance to

5、 loosening. SALIENT CHARACTERISTICS. Performance. Card holders shall hold the circuit card assembly it is attached to firmly in its installed position and prevent loosening or movement as a result of shock and vibration. The card holder shall also provide a thermal transfer path from the circuit car

6、d assembly to the cold plate or heat sink surfaces. Card holders shall also have a visual indicator to show when the assembly is in its relaxed (unlocked) and expanded (locked) state. Interface and physical dimensions. The card holders supplied to this CID specification sheet shall be as specified h

7、erein and meet the general requirements specified in CID AA59789. Material. Unless otherwise specified herein, the card holder materials shall be as specified in AA59789. Actuating screw hex drive socket. The across flats dimension for hex drive socket shall be .140 inch (3.60 mm) for mounting optio

8、ns “R“ and “V“ and .118 inch (3.0 mm) for mounting option “Y“. Cold plate slot width. The recommend cold plate slot width to accommodate the circuit card assembly with attached card holder is .425 inch (10.80 mm) plus the thickness of the printed board of the circuit card assembly (see AA59789). Ins

9、tallation torque. The recommended nominal installation torque is as follows: 20 inch-pounds (2.3 N-m) for assemblies of configuration “C“ and “E“ and 23 inch-pounds (2.6 N-m) for assemblies of configurations “L“ and “D“. AMSC N/A FSC 5998 Provided by IHSNot for ResaleNo reproduction or networking pe

10、rmitted without license from IHS-,-,-AA59789/16A 2 Configuration. The configuration of card holders shall be as specified in table I. The details of a particular configuration consist of those on figures 1 and 2; and may include those on figures 3 or 4. TABLE I. Configuration. Configuration Applicab

11、le figures Hardware options C 1 and 2 No added hardware L 1, 2 and 3 Screw self-locking element E 1, 2 and 4 Additional mounting hole D 1, 2, 3, and 4 Screw self-locking element and additional mounting hole Inches mm Inches mm Inches mm .350 .365 8.89 9.27 .380 .460 9.65 11.68 .49 .75 12.45 19.05 FI

12、GURE 1. Relaxed and expanded dimensions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59789/16A 3 NOTES: 1. Dimensions are in inches. Millimeters are given for general information only. 2. Unless otherwise specified, tolerances are .02 inch (0.5

13、1 mm) for two place decimals and .010 inch (0.25 mm) for three place decimals. 3. Tolerance for the mounting hole spacing is .005 inch (0.13 mm). 4. The across flats dimension for actuating screw hex drive socket shall be .140 inch (3.60 mm) or .118 inch (3.0 mm) for the corresponding mounting optio

14、n (see hex drive socket details). 5. Configuration shown uses captive nut on rear wedge. Alternate design using threaded insert shall be acceptable. FIGURE 1. Relaxed and expanded dimensions Continued. Visual lock indicator (see figure 2). Card holders shall have a visual indicator to show when the

15、card holder is in its relaxed state (unlocked). When the card holder is in the relaxed state (unlocked), the end of the actuating screw shall display a red band on the side of the screw. When the actuating screw on the card holder has been tightened so that the assembly is in the expanded state (loc

16、ked), this red band shall be concealed. FIGURE 2. Visual lock indicator. Finish. The wedge body finish designator shall be as specified in AA59789. The finishes available for this CID specification sheet are as follows: “B“ (black anodize), “E“ (electroless nickel), “H“ (hard black anodize), or “R“

17、(clear chemical film). Length, expanded, and relaxed dimensions. The length designator shall be as specified in AA59789. The lengths available for this CID specification sheet are listed in table II. The length, expanded, and relaxed dimensions shall be as specified on figure 1. TABLE II. Additional

18、 assembly dimensions (see figure 1). 1/ PIN length designator Dimension “LENGTH“ .02 (0.5 mm) Dimension “M“ .005 (0.13 mm) Dimension “M/2“ .005 (0.13 mm) 28 2.8 (71 mm) .65 (16.5 mm) .325 (8.26 mm) 38 3.8 (97 mm) 1.65 (41.9 mm) .825 (20.96 mm) 48 4.8 (122 mm) 2.65 (67.3 mm) 1.325 (33.66 mm) 1/ Dimen

19、sions are in inches. Millimeters, in parenthesis, are given for general information only. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59789/16A 4 Mounting. The mounting designators shall be as specified in AA59789. The mounting options availabl

20、e for this CID specification sheet are as follows: “R“ (rivet mount holes with counterbore and countersink), “V“ (tapped 440 holes), or “M“ (tapped metric M3 x 0.5 holes). See figure 1 and table I for mounting hole spacing requirements. Rivet mount holes. The holes used for rivet mounting shall be .

21、134 to .139 inch (3.40 to 3.53 mm) diameter through holes, countersunk 100 degrees by .150 inch (3.81 mm) deep. Rivets. This card holder uses rivet style B as specified in AA59789 when rivet mounting is used. Configuration hardware options. Card holders can have the following hardware options: no ad

22、ded hardware, screw self-locking element, an additional mounting hole, or a combination of both screw self-locking element and third mounting hole. See table I for the correct PIN configuration identifier. Card holders requiring no added hardware options shall include configuration identifier “C“ in

23、 the PIN (see classification and notes section herein). Screw self-locking element (see figure 3). The use of a screw self-locking element on the screw will provide a prevailing-torque for increased resistance to loosening of the card holder assembly from shock and vibration. The screw self-locking

24、element shall be as specified in AA59789. Card holders requiring a screw self-locking element shall include configuration identifier “L“ in the PIN (see table I, classification and notes section herein). FIGURE 3. Screw self-locking element details. Additional mounting hole (see figure 4). Card hold

25、ers requiring an additional mounting hole shall include configuration identifier “E“ in the PIN (see table I, classification and notes section herein). FIGURE 4. Additional mounting hole details. Screw self-locking element and additional mounting hole. Card holders requiring a screw self-locking ele

26、ment and an additional mounting hole option shall include configuration identifier “D“ in the PIN (see table I, classification and notes section herein). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59789/16A 5 NOTES. PIN. The PIN should be used

27、 for Government purposes to buy commercial products to this CID specification sheet. See the classification section for PIN format example. Source of documents. Commercial Item Description AA59789 Holder, Electrical Card, Wedge Retainers, 5 Piece, For Cold Plate Applications, General Requirements Fo

28、r. (Copies of these documents are available online at https:/assist.dla.mil/quicksearch or https:/assist.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 191115094.) Ordering data. Ordering data shall be as specified in AA59789. Commercial pr

29、oducts. As part of the market analysis and research effort, this CID specification sheet was coordinated with the following manufacturers of commercial products. At the time of CID specification sheet preparation and coordination, these manufacturers were known to have commercial products that would

30、 meet the requirements of this CID specification sheet. (NOTE: This information should not be considered as a list of approved manufacturers or be used to restrict procurement to only the manufacturers shown.) Manufacturer CAGE Manufacturer name and address Manufacturer contact information 61081 Cal

31、mark A Division of Pentair Electronic Packaging 7328 Trade Street San Diego, CA 921213410 Telephone: (858) 7402400 Toll Free: (800) 8547086 Facsimile: (858) 7402430 E-mail: URL: 5BG68 American Circuit Card Retainers, Inc. 2310 E. Orangethorpe Avenue Anaheim, CA 928061231 Telephone: (714) 7386194 F

32、acsimile: (714) 4460119 E-mail: URL: http:/ Part number supersession data. These CID specification sheet PINs supersede the following manufacturers part numbers as shown in table III. The CID PINs listed in table III are only for length designator “50“. See table IV for CID PIN construction using o

33、ther available lengths for this CID specification sheet. This information is being provided to assist in reducing proliferation in the Government inventory system. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59789/16A 6 TABLE III. Commercial pa

34、rt number supersession data. PIN designator AA59789/16 Vendor similar designator or type part number 1/ 2/ CAGE 61081 CAGE 5BG68 CB50M VA2804.80TM3 5280VBA4.80TM3 CB50R VA2804.80H 5280VBA4.80H CB50V VA2804.80T4 5280VBA4.80T4 LB50M VA2804.80TM3L 5280VBA4.80TM3L LB50R VA2804.80HL 5280VBA4.80HL LB50V V

35、A2804.80T4L 5280VBA4.80T4L EB50M VA2804.80ETM3 5280VBA4.80ETM3 EB50R VA2804.80EH 5280VBA4.80EH EB50V VA2804.80ET4 5280VBA4.80ET4 DB50M VA2804.80ETM3L 5280VBA4.80ETM3L DB50R VA2804.80EHL 5280VBA4.80EHL DB50V VA2804.80ET4L 5280VBA4.80ET4L CE50M VEN2804.80TM3 5280VEN4.80TM3 CE50R VEN2804.80H 5280VEN4.8

36、0H CE50V VEN2804.80T4 5280VEN4.80T4 LE50M VEN2804.80TM3L 5280VEN4.80TM3L LE50R VEN2804.80HL 5280VEN4.80HL LE50V VEN2804.80T4L 5280VEN4.80T4L EE50M VEN2804.80ETM3 5280VEN4.80ETM3 EE50R VEN2804.80EH 5280VEN4.80EH EE50V VEN2804.80ET4 5280VEN4.80ET4 DE50M VEN2804.80ETM3L 5280VEN4.80ETM3L DE50R VEN2804.8

37、0EHL 5280VEN4.80EHL DE50V VEN2804.80ET4L 5280VEN4.80ET4L See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59789/16A 7 TABLE III. Commercial part number supersession data Continued. PIN designator AA59789/16 Vendor simi

38、lar designator or type part number 1/ 2/ CAGE 61081 CAGE 5BG68 CH50M VHA2804.80TM3 5280VBH4.80TM3 CH50R VHA2804.80H 5280VBH4.80H CH50V VHA2804.80T4 5280VBH4.80T4 LH50M VHA2804.80TM3L 5280VBH4.80TM3L LH50R VHA2804.80HL 5280VBH4.80HL LH50V VHA2804.80T4L 5280VBH4.80T4L EH50M VHA2804.80ETM3 5280VBH4.80E

39、TM3 EH50R VHA2804.80EH 5280VBH4.80EH EH50V VHA2804.80ET4 5280VBH4.80ET4 DH50M VHA2804.80ETM3L 5280VBH4.80ETM3L DH50R VHA2804.80EHL 5280VBH4.80EHL DH50V VHA2804.80ET4L 5280VBH4.80ET4L CR50M VR2804.80TM3 5280VCC4.80TM3 CR50R VR2804.80H 5280VCC4.80H CR50V VR2804.80T4 5280VCC4.80T4 LR50M VR2804.80TM3L 5

40、280VCC4.80TM3L LR50R VR2804.80HL 5280VCC4.80HL LR50V VR2804.80T4L 5280VCC4.80T4L ER50M VR2804.80ETM3 5280VCC4.80ETM3 ER50R VR2804.80EH 5280VCC4.80EH ER50V VR2804.80ET4 5280VCC4.80ET4 DR50M VR2804.80ETM3L 5280VCC4.80ETM3L DR50R VR2804.80EHL 5280VCC4.80EHL DR50V VR2804.80ET4L 5280VCC4.80ET4L 1/ The CI

41、D PINs listed are only for length designator “50“. 2/ The manufacturers part number shall not be used for procurement to the requirements of this CID specification sheet. At the time of preparation of this CID specification sheet, the aforementioned commercial products were reviewed and could be rep

42、laced by the CID PIN shown. For actual part marking requirements, see the marking paragraph in AA59789. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59789/16A 8 TABLE IV. Example of PIN with available length designators. PIN designator AA59789/1

43、6 Vendor similar designator or type part number 1/ 2/ CAGE 61081 CAGE 5BG68 EH30V VHA2802.80ET4 5280VBH2.80ET4 EH40V VHA2803.80ET4 5280VBH3.80ET4 EH50V VHA2804.80ET4 5280VBH4.80ET4 1/ The manufacturers part number shall not be used for procurement to the requirements of this CID specification sheet.

44、 At the time of preparation of this CID specification sheet, the aforementioned commercial products were reviewed and could be replaced by the CID PIN shown. For actual part marking requirements, see the marking paragraph in AA59789. 2/ Other lengths are available on request. MILITARY INTERESTS: CIV

45、IL AGENCY COORDINATING ACTIVITY: Custodians: GSA FAS Army CR Navy EC Preparing activity: Air Force 85 DLA CC DLA CC Project 59982012006 Review activity: Air Force 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-