DLA A-A-59789 23-2012 HOLDER ELECTRICAL CARD WEDGE RETAINERS 5 PIECE FOR COLD PLATE APPLICATIONS 225 X 225 INCH BODY SIZE WITH TWO THREE OR FOUR MOUNTING HOLES SCREW ACTUATED 7 0 I.pdf

1、INCHPOUND AA59789/23 23 February 2012 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET HOLDER, ELECTRICAL CARD, WEDGE RETAINERS, 5 PIECE, FOR COLD PLATE APPLICATIONS, .225 X .225 INCH BODY SIZE, WITH TWO, THREE, OR FOUR MOUNTING HOLES, SCREW ACTUATED, 7.0 INCH THROUGH 8.5 INCH ASSEMBLY LENGTH The Gen

2、eral Services Administration has authorized the use of this commercial item description for all federal agencies. The complete requirements for procuring electrical card holders described herein shall consist of this document and the latest issue in effect of AA59789. CLASSIFICATION/PART IDENTIFICAT

3、ION NUMBER (PIN). This commercial item description (CID) specification sheet uses a classification system which is included in the Part Identification Number (PIN) as shown in the following example (see notes herein). AA59789 CID number /23 Applicable CID sheet * Configuration (see table I) * Finish

4、 * * Length (see table II) * Mounting (see table I) Example: AA59789/23 FR70S is the PIN for a clear chemical film finished, 6.8 inch (173 mm) long card holder. The card holder also features four tapped mounting holes for use with 256 UNC 2B fasteners and a lockwasher and flat washer under the screw

5、 head for added resistance to loosening. SALIENT CHARACTERISTICS. Performance. Card holders shall hold the circuit card firmly in its installed position and prevent loosening or movement as a result of shock and vibration. It shall also provide a thermal transfer path from the circuit card assembly

6、to the cold plate. Interface and physical dimensions. The card holders supplied to this CID specification sheet shall be as specified herein and meet the general requirements specified in CID AA59789. Material. Unless otherwise specified herein, the card holder materials shall be as specified in AA5

7、9789. Actuating screw hex drive socket. The dimension for hex drive socket shall be .094 inch (2.38 mm) across flats for mounting options “S“, “R“, “P“, “U“, and “T“. Cold plate slot width. The recommend cold plate slot width to accommodate the circuit card assembly with attached card holder is .300

8、 inch (7.62 mm) plus the thickness of the printed board of the circuit card assembly (see AA59789). Installation torque. The recommended nominal installation torque is as follows: 6 inch-pounds (68 N-cm) for assemblies of configuration “A“, “C“, “F“, or “W“ and 7.2 inch-pounds (81 N-cm) for assembli

9、es of configurations “D“, “J“, “L“, or “N“. AMSC N/A FSC 5998 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59789/23 2 Configuration. The configuration of a card holder shall be as specified in table I. The details of a particular configuration c

10、onsist of those on figures 1 and 2, and may include those on figures 3 or 4. Finish. The finish designator shall be as specified in AA59789. The finishes available for this CID specification sheet are as follows: “B“ (black anodize), “C“ (gold chemical film), “E“ (electroless nickel), “H“ (hard blac

11、k anodize), or “R“ (clear chemical film). TABLE I. Configuration. Configuration Number of mounting holes Mounting body style (see figure 2) Mounting options Applicable figures Hardware options A 4 A S, R, T, P 1 and 2 No hardware options added B 1/ C 2 C S, R, T, U Q 3 F 4 A S, R, T, P 1, 2, and 3 L

12、ockwasher and flat washer G 1/ W 2 C S, R, T, U Y 3 N 4 A S, R, T, P 1, 2, and 4 Screw self-lock element P 1/ L 2 C S, R, T, U M 3 J 4 A S, R, T, P 1, 2, 3, and 4 Lockwasher, flat washer, and screw self-lock element K 1/ D 2 C S, R, T, U R 3 1/ This configuration uses index pins and no mounting hole

13、s are present (see figure 2). Length, expanded and relaxed dimensions. The length designator shall be as specified in AA59789. The lengths available for this CID specification sheet are listed in table II. The length, expanded, and relaxed dimensions shall be as specified on figure 1. Mounting body

14、style (see figure 2 and table II). Two mounting body styles are available on this CID specification sheet, style A or style C. The primary difference in the two mounting body styles are the location of mounting holes on the mounting body as depicted on figure 2. Mounting body style A has either four

15、 mounting holes for fasteners or two indexing pins centered on the mounting body that are .900 inch (22.86 mm) apart. Mounting body style C can have two or three holes on the mounting body. Also, the distance between the mounting holes increases for assembly lengths of 7.5 inches (190.5 mm) and over

16、 (see table II). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59789/23 3 Inches mm Inches mm Inches mm .125 .140 3.18 3.56 .225 .270 5.72 6.86 .30 .900 7.6 22.86 NOTES: 1. Dimensions are in inches. Millimeters are given for general information o

17、nly. 2. Unless otherwise specified, tolerances are .02 inch (0.51 mm) for two place decimals and .010 inch (0.25 mm) for three place decimals. 3. Screw and alignment spring not shown. See table II and figure 2 for hole spacing requirements. 4. The across flats dimension for hex drive socket shall be

18、 .094 inch (2.38 mm). 5. Mounting body style “A“ is capable of safely expanding to .330 inch (8.38 mm) and mounting body style “C“ is capable of expanding to .325 inch (8.26 mm) minimum. 6. Maximum screw advance is .12 inch (3.0 mm) for mounting body style “A“ and .14 inch (3.6 mm) for mounting body

19、 style “C“. FIGURE 1. Relaxed and expanded dimensions (mounting body “C“ with two mounting holes shown). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59789/23 4 TABLE II. Additional assembly dimensions (see figures 1 and 2). 1/ PIN length design

20、ator Dimension “L“ .02 (0.5) Mounting body style Dimension “A“ .01 (0.3) Dimension “B“ 2/ Dimension “M“ 3/ Dimension “E“ 3/ Dimension “F“ 3/ 70 6.8 (172.7) A 4/ 3.50 (88.9) 1.30 (33.0) .900 (22.9) A 5/ 3.50 (88.9) .40 (10.2) 2.700 (68.6) 1.800 (45.7) .900 (22.9) C 6/ 2.95 (74.9) C 7/ 1.60 (40.6) 2.9

21、5 (74.9) .900 (22.9) .45 (11.4) 75 7.3 (185.4) A 4/ 4.00 (101.6) 1.55 (39.4) .900 (22.9) A 5/ 4.00 (101.6) .65 (16.5) 2.700 (68.6) 1.800 (45.7) .900 (22.9) C 6/ 3.20 (81.3) C 7/ 3.20 (81.3) .900 (22.9) .45 (11.4) 80 7.8 (198.1) A 4/ 3.50 (88.9) 1.30 (33.0) .900 (22.9) A 5/ 3.50 (88.9) .40 (10.2) 2.7

22、00 (68.6) 1.800 (45.7) .900 (22.9) C 6/ 2.95 (74.9) C 7/ 2.95 (74.9) 1.900 (48.3) .95 (24.1) 85 8.3 (210.8) A 4/ 4.00 (101.6) 1.55 (39.4) .900 (22.9) A 5/ 4.00 (101.6) .65 (16.5) 2.700 (68.6) 1.800 (45.7) .900 (22.9) C 6/ 3.20 (81.3) C 7/ 3.20 (81.3) 1.900 (48.3) .95 (24.1) 1/ Dimensions are in inch

23、es. Millimeters, in parenthesis, are given for general information only. 2/ Tolerance for the hole offset is .02 inch (0.5 mm) for mounting body style A and .045 inch (1.14 mm) for mounting body style C. 3/ Tolerance for the hole spacing is .005 inch (0.51 mm). 4/ Mounting body with 2 indexing pins

24、(see mounting body style A on figure 2). 5/ Mounting body with 4 mounting holes (see mounting body style A on figure 2). 6/ Mounting body with 2 mounting holes (see mounting body style C on figure 2). 7/ Mounting body with 3 mounting holes (see mounting body style C on figure 2). Mounting. The mount

25、ing designators shall be as specified in AA59789. The mounting options available for this CID specification sheet are as follows: “P“ (.062 x .040 index pins; mounting body style A only), “R“ (rivet mount holes with counterbore and countersink), “S“ (tapped 256 holes), or “T“ (tapped 080 holes). See

26、 figure 2 for mounting hole spacing requirements. Card holders using mounting option “P“ and “R“ may be shipped unassembled. Rivet mount holes. The holes used for rivet mounting shall be .066/.073 inch (1.68/1.85 mm) diameter, countersunk 100 degrees by .140 inch (3.56 mm) diameter through holes wit

27、h a counterbore of .156 inch (3.96 mm) diameter by .200 inch (5.08 mm) deep. Rivets. This card holder uses rivet style A as specified in AA59789 when rivet mounting is used. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59789/23 5 NOTES: 1. Dimen

28、sions are in inches. Millimeters are given for general information only. 2. See table II for dimensions B, E, F, and M. FIGURE 2. Mounting body style details. Configuration hardware options. Card holders can have the following hardware options. See table I for the correct PIN configuration identifie

29、r for the hardware associated with the configuration. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59789/23 6 Lockwasher and flat washer (see figure 3). A lockwasher and flat washer located under the screw head will provide for additional resist

30、ance to loosening from shock and vibration. When a lockwasher and flat washer are required on a card holder, the configuration identifier “F“ or “W“ shall be used in the PIN (see classification and notes). FIGURE 3. Lockwasher and flat washer details. Screw self-locking element (see figure 4). The u

31、se of a screw self-locking element will provide prevailing torque for resistance to loosening of the assembly from shock vibration. The screw self-locking element shall be in accordance with AA59789. When a screw self locking element is required on a card holder, the configuration identifier “L“ or

32、“N“ shall be used in the PIN (see classification and notes). FIGURE 4. Screw self-locking element details. Lockwasher, flat washer, and screw self-locking element. Card holders requiring a lockwasher, flat washer, and screw self-locking element option shall include configuration identifier “D“ or “J

33、“ in the PIN (see classification and notes). NOTES. PIN. The PIN should be used for Government purposes to buy commercial products to this CID specification sheet. See the classification section for PIN format example. Source of documents. Commercial Item Description AA59789 Holder, Electrical Card,

34、 Wedge Retainers, 5 Piece, For Cold Plate Applications, General Requirements For. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or https:/assist.daps.dla.mil/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia,

35、PA 191115094.) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59789/23 7 Ordering data. Ordering data is as specified in AA59789. Commercial products. As part of the market analysis and research effort, this CID specification sheet was coordinated

36、 with the following manufacturers of commercial products. At the time of CID specification sheet preparation and coordination, these manufacturers were known to have commercial products that would meet the requirements of this CID specification sheet. (NOTE: This information should not be considered

37、 as a list of approved manufacturers or be used to restrict procurement to only the manufacturers shown.) Manufacturer CAGE Manufacturer name and address Manufacturer contact information 18915 Birtcher A Division of Pentair Technical Products 7328 Trade Street San Diego, CA 921213410 Telephone: (858

38、) 7402400 Toll Free: (800) 8547086 Facsimile: (858) 6794555 (URL): 61081 Calmark A Division of Pentair Technical Products 7328 Trade Street San Diego, CA 921213410 Telephone: (858) 7402400 Toll Free: (800) 8547086 Facsimile: (858) 7402430 Electronic mail: URL: 5BG68 Card Locks Unlimited, Inc. 231

39、0 E. Orangethorpe Avenue Anaheim, CA 928061231 Telephone: (714) 7386194 Facsimile: (714) 4460119 E-mail: URL: Part number supersession data. These CID specification sheet PINs supersede the following manufacturers part numbers in table III and on DESC Drawing 89064 (table IV) as shown. The CID PIN

40、s listed in table III are only for length designator “80“. See table V for CID PIN construction using other available lengths for this CID specification sheet. This information is being provided to assist in reducing proliferation in the Government inventory system. Provided by IHSNot for ResaleNo r

41、eproduction or networking permitted without license from IHS-,-,-AA59789/23 8 TABLE III. Commercial part number supersession data. PIN designator AA59789/23 Vendor similar designator or type part number 1/ CAGE 18915 PIN designator AA59789/23 Vendor similar designator or type part number 1/ CAGE 610

42、81 Vendor similar designator or type part number 1/ CAGE 5BG68 AB80S 40516B CB80S A226CR7.80T2 5226BA7.80T2 AB80R 40516BR CB80R A226CR7.80H 5226BA7.80H AB80T 40516BT CB80T A226CR7.80T0 5226BA7.80T0 AB80P 40516BP CB80U A226CR7.80TM2 5226BA7.80TM2 FB80S 40516BLF WB80S WA226CR7.80T2 5226WBA7.80T2 FB80R

43、 40516BLFR WB80R WA226CR7.80H 5226WBA7.80H FB80T 40516BLFT WB80T WA226CR7.80T0 5226WBA7.80T0 FB80P 40516BLFP WB80U WA226CR7.80TM2 5226WBA7.80TM2 NB80S 40516BL LB80S A226CR7.80T2L 5226BA7.80T2L NB80R 40516BRL LB80R A226CR7.80HL 5226BA7.80HL NB80T 40516BTL LB80T A226CR7.80T0L 5226BA7.80T0L NB80P 40516

44、BPL LB80U A226CR7.80TM2L 5226BA7.80TM2L JB80S 40516BLFL DB80S WA226CR7.80T2L 5226WBA7.80T2L JB80R 40516BLFRL DB80R WA226CR7.80HL 5226WBA7.80HL JB80T 40516BLFTL DB80T WA226CR7.80T0L 5226WBA7.80T0L JB80P 40516BLFPL DB80U WA226CR7.80TM2L 5226WBA7.80TM2L AC80S 40516 CC80S 226CR7.80T2 5226CG7.80T2 AC80R

45、40516R CC80R 226CR7.80H 5226CG7.80H AC80T 40516T CC80T 226CR7.80T0 5226CG7.80T0 AC80P 40516P CC80U 226CR7.80TM2 5226CG7.80TM2 FC80S 40516LF WC80S W226CR7.80T2 5226WCG7.80T2 FC80R 40516LFR WC80R W226CR7.80H 5226WCG7.80H FC80T 40516LFT WC80T W226CR7.80T0 5226WCG7.80T0 FC80P 40516LFP WC80U W226CR7.80TM

46、2 5226WCG7.80TM2 NC80S 40516L LC80S 226CR7.80T2L 5226CG7.80T2L NC80R 40516RL LC80R 226CR7.80HL 5226CG7.80HL NC80T 40516TL LC80T 226CR7.80T0L 5226CG7.80T0L NC80P 40516PL LC80U 226CR7.80TM2L 5226CG7.80TM2L JC80S 40516LFL DC80S W226CR7.80T2L 5226WCG7.80T2L JC80R 40516LFRL DC80R W226CR7.80HL 5226WCG7.80

47、HL JC80T 40516LFTL DC80T W226CR7.80T0L 5226WCG7.80T0L JC80P 40516LFPL DC80U W226CR7.80TM2L 5226WCG7.80TM2L See footnote at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59789/23 9 TABLE III. Commercial part number supersession data Continued. PIN designator AA59789/23 Vendor similar designator or type part number 1/ CAGE 18915 PIN designator AA59789/23 Vendor similar designator or type part number 1/ CAGE 61081 Vendor similar designator or typ