DLA A-A-59789 25-2012 HOLDER ELECTRICAL CARD WEDGE RETAINERS 5 PIECE FOR COLD PLATE APPLICATIONS 225 X 225 INCH BODY SIZE SCREW ACTUATED WITH CAPTIVE SCREW.pdf

1、INCHPOUND AA59789/25 25 March 2012 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET HOLDER, ELECTRICAL CARD, WEDGE RETAINERS, 5 PIECE, FOR COLD PLATE APPLICATIONS, .225 X .225 INCH BODY SIZE, SCREW ACTUATED, WITH CAPTIVE SCREW The General Services Administration has authorized the use of this commerc

2、ial item description for all federal agencies. The complete requirements for procuring electrical card holders described herein shall consist of this document and the latest issue in effect of AA59789. CLASSIFICATION/PART IDENTIFICATION NUMBER (PIN). This commercial item description (CID) specificat

3、ion sheet uses a classification system which is included in the PIN as shown in the following example (see notes herein). AA59789 CID number /25 Applicable CID sheet * Configuration (see table I) * Finish * * Length (see table II) * Mounting Example: AA59789/25DE90T is the PIN for an electroless nic

4、kel finished, 8.8 inch (71.1 mm) long card holder. The card holder also features three tapped mounting holes for use with 080 UNF 2B fasteners and a screw selflocking element for added resistance to loosening. SALIENT CHARACTERISTICS. Performance. Card holders shall hold the circuit card firmly in i

5、ts installed position and prevent loosening or movement as a result of shock and vibration. It shall also provide a thermal transfer path from the circuit card assembly to the cold plate. Interface and physical dimensions. The card holders supplied to this CID specification sheet shall be as specifi

6、ed herein and meet the general requirements specified in CID AA59789. Card holders shall also have a screw retention feature to prevent unintentional disassembly of the card holder. Material. Unless otherwise specified herein, the card holder materials shall be as specified in AA59789. Actuating scr

7、ew hex drive socket. The dimension for hex drive socket shall be .094 inch (2.38 mm) across flats for mounting options “M“, “R“, “S“, “T“, and “U“. Cold plate slot width. The recommend cold plate slot width to accommodate the circuit card assembly with attached card holder is .250 inch (6.35 mm) plu

8、s the thickness of the printed board of the circuit card assembly (see AA59789). Installation torque. The recommended nominal installation torque is follows: 6 inch-pounds (0.7 N-m) for card holders of configuration “C“ or “E“ and 7 to 8 inch-pounds (0.8 to 0.9 N-m) for assemblies of configurations

9、“L“ or “D“. Configuration. The configuration of a card holder shall be as specified in table I. The details of a particular configuration consist of those on figures 1 and 2, and may include those on figures 3 and 4. AMSC N/A FSC 5998 Provided by IHSNot for ResaleNo reproduction or networking permit

10、ted without license from IHS-,-,-AA59789/25 2 TABLE I. Configuration. Configuration Applicable figures Hardware options C 1 and 2 No added options L 1, 2, and 3 Screw self-locking element E 1, 2, and 4 Additional mounting hole D 1, 2, 3, and 4 Screw self-locking element and additional mounting hole

11、Inches mm Inches mm Inches mm .18 .225 4.57 5.72 .230 .290 5.84 7.37 .30 .80 7.62 20.32 NOTES: 1. Dimensions are in inches. Millimeter equivalents are given for general information only. 2. Unless otherwise specified, tolerances are for .02 inch (0.51 mm) for two place decimals and .010 inch (0.25 m

12、m) for three place decimals. 3. Tolerance for the hole spacing is .005 inch (0.13 mm). 4. The across flats dimension for hex drive socket shall be .094 inch (2.38 mm). FIGURE 1. Relaxed and expanded dimensions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from

13、 IHS-,-,-AA59789/25 3 Captive screw (see figure 2). The captive screw feature prevents the unintentional disassembly of screw from front wedge. FIGURE 2. Captive screw details. Finish. The finish designator shall be as specified in AA59789. The finishes available for this CID specification sheet are

14、 as follows: “B“ (black anodize), “E“ (electroless nickel), or “H“ (hard black anodize). Length, expanded, and relaxed dimensions. The length designator shall be as specified in AA59789 and the lengths available for this CID specification sheet are listed in table II. The length, expanded, and relax

15、ed dimensions shall be as specified on figure 1. TABLE II. Additional card holder dimensions (see figure 1). 1/ PIN length designator Dimension “Length“ .02 (0.5) Dimension “M“ .01 (0.3) Dimension “M/2“ .02 (0.5) 30 2.80 (71.1) .90 (22.9) .45 (11.4) 40 3.80 (96.5) 1.90 (48.3) .95 (24.1) 50 4.80 (121

16、.9) 2.90 (73.7) 1.45 (36.8) 60 5.80 (147.3) 3.90 (99.1) 1.95 (49.5) 70 6.80 (172.7) 4.90 (124.5) 2.45 (62.2) 80 7.80 (198.1) 5.90 (149.9) 2.95 (74.9) 90 8.80 (223.5) 6.90 (175.3) 3.45 (87.6) 1/ Dimensions are in inches. Millimeters, in parenthesis, are given for information only. Mounting. The mount

17、ing designators shall be as specified in AA59789. The mounting options available for this CID specification sheet are as follows: “M“ (tapped metric M2.5 x 0.45 holes), “R“ (rivet mount holes with counterbore and countersink), “S“ (tapped 2-56 holes), “T“ (tapped 0-80 holes), or “U“ (tapped metric M

18、2 x 0.4 holes). See figures 1 and 4 for mounting hole spacing requirements. Rivet mounting holes. The holes used for rivet mounting shall be .068/.073 inch (1.73/1.85 mm) diameter, countersunk 100 degrees by .060 inch (1.52 mm) deep. Rivets. This card holder uses rivet type A as specified in AA59789

19、 when rivet mounting is used. Hardware options. Card holders can have the following hardware options: no hardware options added, screw self-lock element (see figure 3), additional mounting hole (see figure 4) or screw self lock element and additional mounting hole. See table I for the correct PIN co

20、nfiguration identifier for the hardware option needed. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59789/25 4 Screw self-locking element (see figure 3). The use of a screw self-locking element will provide prevailing torque for resistance to lo

21、osening from shock vibration. The screw self-locking element shall be as specified in AA59789. Card holders requiring a screw self-locking element shall include configuration identifier “L“ in the PIN (see classification and table I). FIGURE 3. Screw self-locking element details. Additional mounting

22、 hole (see figure 4). Card holders requiring an additional mounting hole shall include configuration identifier “E“ in the PIN (see classification and table I). FIGURE 4. Additional mounting hole details. Screw self-locking element and additional mounting hole. Card holders requiring a screw self-lo

23、cking element and an additional mounting hole option shall include configuration identifier “D“ in the PIN (see classification and table I). NOTES. PIN. The PIN should be used for Government purposes to buy commercial products to this CID specification sheet. See the classification section for PIN f

24、ormat example. Source of documents. Commercial Item Description AA59789 Holder, Electrical Card, Wedge Retainers, 5 Piece, For Cold Plate Applications, General Requirements For. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or https:/assist.daps.dla.mil/

25、or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 191115094.) Ordering data. Ordering data is as specified in AA59789. Commercial products. As part of the market analysis and research effort, this CID specification sheet was coordinated with the follo

26、wing manufacturers of commercial products. At the time of CID specification sheet preparation and coordination, these manufacturers were known to have commercial products that would meet the requirements of this CID specification sheet. (NOTE: This information should not be considered as a list of a

27、pproved manufacturers or be used to restrict procurement to only the manufacturers shown.) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59789/25 5 Manufacturer CAGE Manufacturer name and address Manufacturer contact information 61081 Calmark A D

28、ivision of Pentair Technical Products 7328 Trade Street San Diego, CA 921213410 Telephone: (858) 7402400 Toll Free: (800) 8547086 Facsimile: (858) 7402430 Electronic mail: URL: 5BG68 Card Locks Unlimited, Inc. 2310 E. Orangethorpe Avenue Anaheim, CA 928061231 Telephone: (714) 7386194 Facsimile: (7

29、14) 4460119 E-mail: URL: Part number supersession data. This CID specification sheet PINs supersedes the following manufacturers part numbers as shown in table III. The CID PINs listed in table III are only for length designator “80“. See table IV for CID PIN construction using other available len

30、gths for this CID specification sheet. This information is being provided to assist in reducing proliferation in the Government inventory system. TABLE III. Commercial part number supersession data. PIN designator AA59789/25 Vendor similar designator or type part number 1/ CAGE 61081 Vendor similar

31、designator or type part number 1/ CAGE 5BG68 CB80M A2657.80TM2.5K 5265BA7.80TM2.5K CB80R A2657.80HK 5265BA7.80HK CB80S A2657.80T2K 5265BA7.80T2K CB80T A2657.80T0K 5265BA7.80T0K CB80U A2657.80TM2K 5265BA7.80TM2K EB80M A2657.80ETM2.5K 5265BA7.80ETM2.5K EB80R A2657.80EHK 5265BA7.80EHK EB80S A2657.80ET2

32、K 5265BA7.80ET2K EB80T A2657.80ET0K 5265BA7.80ET0K EB80U A2657.80ETM2K 5265BA7.80ETM2K LB80M A2657.80TM2.5LK 5265BA7.80TM2.5LK LB80R A2657.80HLK 5265BA7.80HLK LB80S A2657.80T2LK 5265BA7.80T2LK LB80T A2657.80T0LK 5265BA7.80T0LK LB80U A2657.80TM2LK 5265BA7.80TM2LK See footnotes at end of table. Provid

33、ed by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59789/25 6 TABLE III. Commercial part number supersession data. PIN designator AA59789/25 Vendor similar designator or type part number 1/ CAGE 61081 Vendor similar designator or type part number 1/ CAGE 5B

34、G68 DB80M A2657.80ETM2.5LK 5265BA7.80ETM2.5LK DB80S A2657.80EHLK 5265BA7.80EHLK DB80R A2657.80ET2LK 5265BA7.80ET2LK DB80T A2657.80ET0LK 5265BA7.80ET0LK DB80U A2657.80ETM2LK 5265BA7.80ETM2LK CE80M EN2657.80TM2.5K 5265EN7.80TM2.5K CE80R EN2657.80HK 5265EN7.80HK CE80S EN2657.80T2K 5265EN7.80T2K CE80T E

35、N2657.80T0K 5265EN7.80T0K CE80U EN2657.80TM2K 5265EN7.80TM2K EE80M EN2657.80ETM2.5K 5265EN7.80ETM2.5K EE80R EN2657.80EHK 5265EN7.80EHK EE80S EN2657.80ET2K 5265EN7.80ET2K EE80T EN2657.80ET0K 5265EN7.80ET0K EE80U EN2657.80ETM2K 5265EN7.80ETM2K LE80M EN2657.80TM2.5LK 5265EN7.80TM2.5LK LE80R EN2657.80HL

36、K 5265EN7.80HLK LE80S EN2657.80T2LK 5265EN7.80T2LK LE80T EN2657.80T0LK 5265EN7.80T0LK LE80U EN2657.80TM2LK 5265EN7.80TM2LK DE80M EN2657.80ETM2.5LK 5265EN7.80ETM2.5LK DE80S EN2657.80EHLK 5265EN7.80EHLK DE80R EN2657.80ET2LK 5265EN7.80ET2LK DE80T EN2657.80ET0LK 5265EN7.80ET0LK DE80U EN2657.80ETM2LK 526

37、5EN7.80ETM2LK CH80M HA2657.80TM2.5K 5265BH7.80TM2.5K CH80R HA2657.80HK 5265BH7.80HK CH80S HA2657.80T2K 5265BH7.80T2K CH80T HA2657.80T0K 5265BH7.80T0K CH80U HA2657.80TM2K 5265BH7.80TM2K See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license

38、 from IHS-,-,-AA59789/25 7 TABLE III. Commercial part number supersession data Continued. PIN designator AA59789/25 Vendor similar designator or type part number 1/ CAGE 61081 Vendor similar designator or type part number 1/ CAGE 5BG68 EH80M HA2657.80ETM2.5K 5265BH7.80ETM2.5K EH80R HA2657.80EHK 5265

39、BH7.80EHK EH80S HA2657.80ET2K 5265BH7.80ET2K EH80T HA2657.80ET0K 5265BH7.80ET0K EH80U HA2657.80ETM2K 5265BH7.80ETM2K LH80M HA2657.80TM2.5LK 5265BH7.80TM2.5LK LH80R HA2657.80HLK 5265BH7.80HLK LH80S HA2657.80T2LK 5265BH7.80T2LK LH80T HA2657.80T0LK 5265BH7.80T0LK LH80U HA2657.80TM2LK 5265BH7.80TM2LK DH

40、80M HA2657.80ETM2.5LK 5265BH7.80ETM2.5LK DH80S HA2657.80EHLK 5265BH7.80EHLK DH80R HA2657.80ET2LK 5265BH7.80ET2LK DH80T HA2657.80ET0LK 5265BH7.80ET0LK DH80U HA2657.80ETM2LK 5265BH7.80ETM2LK 1/ The manufacturers part number shall not be used for procurement to the requirements of this CID specificatio

41、n sheet. At the time of preparation of this CID specification sheet, the aforementioned commercial products were reviewed and could be replaced by the CID PIN shown. For actual part marking requirements, see the marking paragraph in AA59789. TABLE IV. Example of PIN with available length designators

42、. PIN designator AA59789/25 Vendor similar designator or type part number 1/ 2/ CAGE 61081 Vendor similar designator or type part number 1/ 2/ CAGE 5BG68 DE30T EN2652.80ET0LK 5265EN2.80ET0LK DE40T EN2653.80ET0LK 5265EN3.80ET0LK DE50T EN2654.80ET0LK 5265EN4.80ET0LK DE60T EN2655.80ET0LK 5265EN5.80ET0L

43、K DE70T EN2656.80ET0LK 5265EN6.80ET0LK DE80T EN2657.80ET0LK 5265EN7.80ET0LK DE90T EN2658.80ET0LK 5265EN8.80ET0LK See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59789/25 8 TABLE IV. Example of PIN with available lengt

44、h designators Continued. 1/ The manufacturers part number shall not be used for procurement to the requirements of this CID specification sheet. At the time of preparation of this CID specification sheet, the aforementioned commercial products were reviewed and could be replaced by the CID PIN shown

45、. For actual part marking requirements, see the marking paragraph in AA59789. 2/ Other lengths are available on request. MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: Custodians: GSA FAS Army CR Navy EC Preparing activity: Air Force 85 DLA CC DLA CC Project 59982011025 Review activity: Air

46、 Force 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-