DLA A-A-59789 26-2012 HOLDER ELECTRICAL CARD WEDGE RETAINERS 5 PIECE FOR COLD PLATE APPLICATIONS 225 X 225 INCH BODY SIZE SCREW ACTUATED WITH CAPTIVE SCREW AND VISUAL LOCK INDICATI.pdf

1、INCHPOUND AA59789/26 26 March 2012 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET HOLDER, ELECTRICAL CARD, WEDGE RETAINERS, 5 PIECE, FOR COLD PLATE APPLICATIONS, .225 X .225 INCH BODY SIZE, SCREW ACTUATED, WITH CAPTIVE SCREW AND VISUAL LOCK INDICATION The General Services Administration has authori

2、zed the use of this commercial item description for all federal agencies. The complete requirements for procuring electrical card holders described herein shall consist of this document and the latest issue in effect of AA59789. CLASSIFICATION/PART IDENTIFICATION NUMBER (PIN). This commercial item d

3、escription (CID) specification sheet uses a classification system which is included in the PIN as shown in the following example (see notes herein). AA59789 CID number /26 Applicable CID sheet * Configuration (see table I) * Finish * * Length (see table II) * Mounting Example: AA59789/10LH50S is the

4、 PIN for a hard black anodize finished, 4.8 inch (121.9 mm) long card holder with visual lock indication. The card holder also features two tapped mounting holes for use with 256 UNC 2B fasteners and a screw selflocking element for added resistance to loosening. SALIENT CHARACTERISTICS. Performance.

5、 Card holders shall hold the circuit card firmly in its installed position and prevent loosening or movement as a result of shock and vibration. It shall also provide a thermal transfer path from the circuit card assembly to the cold plate. Interface and physical dimensions. The card holders supplie

6、d to this CID specification sheet shall be as specified herein and meet the general requirements specified in CID AA59789. Card holders shall have a screw retention feature to prevent unintentional disassembly of the card holder. Card holders shall also have a visual indicator to show when the assem

7、bly is in its relaxed (unlocked) and expanded (locked) state. Material. Unless otherwise specified herein, the card holder materials shall be as specified in AA59789. Actuating screw hex drive socket. The dimension for hex drive socket shall be .094 inch (2.38 mm) across flats for mounting options “

8、M“, “R“, “S“, “T“, and “U“. Cold plate slot width. The recommend cold plate slot width to accommodate the circuit card assembly with attached card holder is .250 inch (6.35 mm) plus the thickness of the printed board of the circuit card assembly (see AA59789). Installation torque. The recommended no

9、minal installation torque is follows: 6 inch-pounds (0.7 N-m) for card holders of configuration “C“ or “E“ and 7 to 8 inch-pounds (0.8 to 0.9 N-m) for assemblies of configurations “L“ or “D“. Configuration. The configuration of a card holder shall be as specified in table I. The details of a particu

10、lar configuration consist of those on figures 1, 2 and 3, and may include those on figures 4 and 5. AMSC N/A FSC 5998 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59789/26 2 TABLE I. Configuration. Configuration Applicable figures Hardware optio

11、ns C 1, 2 and 3 No added options L 1, 2, 3 and 4 Screw self-locking element E 1, 2, 3 and 5 Additional mounting hole D 1, 2, 3, 4 and 5 Screw self-locking element and additional mounting hole Inches mm Inches mm Inches mm Inches mm Inches mm .225 5.71 .230 5.84 .290 7.37 .35 8.9 .80 20.3 NOTES: 1. D

12、imensions are in inches. Millimeter equivalents are given for general information only. 2. Unless otherwise specified, tolerances are .02 inch (0.51 mm) for two place decimals and .010 inch (0.25 mm) for three place decimals. 3. Tolerance for the hole spacing is .005 inch (0.13 mm). 4. The across fl

13、ats dimension for hex drive socket shall be .094 inch (2.38 mm). FIGURE 1. Relaxed and expanded dimensions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59789/26 3 Captive screw (see figure 2). The captive screw feature prevents the unintentiona

14、l disassembly of screw from front wedge. FIGURE 2. Captive screw details. Visual lock indicator (see figure 3). Card holders shall have a visual indicator to show when the card holder is in its relaxed state (unlocked). When the card holder is in the relaxed state (unlocked), the end of the actuatin

15、g screw shall display a red band on the side of the screw. When the actuating screw on the card holder has been tightened so that the assembly is in the expanded state (locked), this red band shall be concealed. FIGURE 3. Visual lock indicator. TABLE II. Additional card holder dimensions (see figure

16、 1). 1/ PIN length designator Dimension “Length“ .02 (0.5) Dimension “M“ .01 (0.3) Dimension “M/2“ .02 (0.5) 30 2.80 (71.1) .90 (22.9) .45 (11.4) 40 3.80 (96.5) 1.90 (48.3) .95 (24.1) 50 4.80 (121.9) 2.90 (73.7) 1.45 (36.8) 60 5.80 (147.3) 3.90 (99.1) 1.95 (49.5) 70 6.80 (172.7) 4.90 (124.5) 2.45 (6

17、2.2) 80 7.80 (198.1) 5.90 (149.9) 2.95 (74.9) 90 8.80 (223.5) 6.90 (175.3) 3.45 (87.6) 1/ Dimensions are in inches. Millimeters, in parenthesis, are given for information only. Finish. The finish designator shall be as specified in AA59789. The finishes available for this CID specification sheet are

18、 as follows: “B“ (black anodize), “E“ (electroless nickel), or “H“ (hard black anodize). Length, expanded, and relaxed dimensions. The length designator shall be as specified in AA59789 and the lengths available for this CID specification sheet are listed in table II. The length, expanded, and relax

19、ed dimensions shall be as specified on figure 1. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59789/26 4 Mounting. The mounting designators shall be as specified in AA59789. The mounting options available for this CID specification sheet are as

20、follows: “M“ (tapped metric M2.5 x 0.45 holes), “R“ (rivet mount holes with counterbore and countersink), “S“ (tapped 2-56 holes), “T“ (tapped 0-80 holes), or “U“ (tapped metric M2 x 0.4 holes). See figures 1 and 5 for mounting hole spacing requirements. Rivet mounting holes. The holes used for rive

21、t mounting shall be .068/.073 inch (1.73/1.85 mm) diameter, countersunk 100 degrees by .060 inch (1.52 mm) deep. Rivets. This card holder uses rivet type A as specified in AA59789 when rivet mounting is used. Hardware options. Card holders can have the following hardware options: no hardware options

22、 added, screw self-lock element (see figure 4), additional mounting hole (see figure 5) or screw self lock element and additional mounting hole. See table I for the correct PIN configuration identifier for the hardware option needed. Screw self-locking element (see figure 4). The use of a screw self

23、-locking element will provide prevailing torque for resistance to loosening from shock vibration. Card holders requiring a screw self-locking element shall include configuration identifier “L“ in the PIN (see classification and table I). FIGURE 4. Screw self-locking element details. Additional mount

24、ing hole (see figure 5). Card holders requiring an additional mounting hole shall include configuration identifier “E“ in the PIN (see classification and table I). FIGURE 5. Additional mounting hole details. Screw self-locking element and additional mounting hole. Card holders requiring a screw self

25、-locking element and an additional mounting hole option shall include configuration identifier “D“ in the PIN (see classification and table I). NOTES. PIN. The PIN should be used for Government purposes to buy commercial products to this CID specification sheet. See the classification section for PI

26、N format example. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59789/26 5 Source of documents. Commercial Item Description AA59789 Holder, Electrical Card, Wedge Retainers, 5 Piece, For Cold Plate Applications, General Requirements For. (Copies

27、of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or https:/assist.daps.dla.mil/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 191115094.) Ordering data. Ordering data is as specified in AA59789. Commercial product

28、s. As part of the market analysis and research effort, this CID specification sheet was coordinated with the following manufacturers of commercial products. At the time of CID specification sheet preparation and coordination, these manufacturers were known to have commercial products that would meet

29、 the requirements of this CID specification sheet. (NOTE: This information should not be considered as a list of approved manufacturers or be used to restrict procurement to only the manufacturers shown.) Manufacturer CAGE Manufacturer name and address Manufacturer contact information 61081 Calmark

30、A Division of Pentair Technical Products 7328 Trade Street San Diego, CA 921213410 Telephone: (858) 7402400 Toll Free: (800) 8547086 Facsimile: (858) 7402430 Electronic mail: URL: 5BG68 Card Locks Unlimited, Inc. 2310 E. Orangethorpe Avenue Anaheim, CA 928061231 Telephone: (714) 7386194 Facsimile:

31、 (714) 4460119 E-mail: URL: Part number supersession data. This CID specification sheet PINs supersedes the following manufacturers part numbers as shown in table III. The CID PINs listed in table III are only for length designator “80“. See table IV for CID PIN construction using other available

32、lengths for this CID specification sheet. This information is being provided to assist in reducing proliferation in the Government inventory system. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59789/26 6 TABLE III. Commercial part number supers

33、ession data. PIN designator AA59789/26 Vendor similar designator or type part number 1/ CAGE 61081 Vendor similar designator or type part number 1/ CAGE 5BG68 CB80M VA2657.80TM2.5K 5265VBA7.80TM2.5K CB80R VA2657.80HK 5265VBA7.80HK CB80S VA2657.80T2K 5265VBA7.80T2K CB80T VA2657.80T0K 5265VBA7.80T0K C

34、B80U VA2657.80TM2K 5265VBA7.80TM2K EB80M VA2657.80ETM2.5K 5265VBA7.80ETM2.5K EB80R VA2657.80EHK 5265VBA7.80EHK EB80S VA2657.80ET2K 5265VBA7.80ET2K EB80T VA2657.80ET0K 5265VBA7.80ET0K EB80U VA2657.80ETM2K 5265VBA7.80ETM2K LB80M VA2657.80TM2.5LK 5265VBA7.80TM2.5LK LB80R VA2657.80HLK 5265VBA7.80HLK LB8

35、0S VA2657.80T2LK 5265VBA7.80T2LK LB80T VA2657.80T0LK 5265VBA7.80T0LK LB80U VA2657.80TM2LK 5265VBA7.80TM2LK DB80M VA2657.80ETM2.5LK 5265VBA7.80ETM2.5LK DB80S VA2657.80EHLK 5265VBA7.80EHLK DB80R VA2657.80ET2LK 5265VBA7.80ET2LK DB80T VA2657.80ET0LK 5265VBA7.80ET0LK DB80U VA2657.80ETM2LK 5265VBA7.80ETM2

36、LK CE80M VEN2657.80TM2.5K 5265VEN7.80TM2.5K CE80R VEN2657.80HK 5265VEN7.80HK CE80S VEN2657.80T2K 5265VEN7.80T2K CE80T VEN2657.80T0K 5265VEN7.80T0K CE80U VEN2657.80TM2K 5265VEN7.80TM2K EE80M VEN2657.80ETM2.5K 5265VEN7.80ETM2.5K EE80R VEN2657.80EHK 5265VEN7.80EHK EE80S VEN2657.80ET2K 5265VEN7.80ET2K E

37、E80T VEN2657.80ET0K 5265VEN7.80ET0K EE80U VEN2657.80ETM2K 5265VEN7.80ETM2K See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59789/26 7 TABLE III. Commercial part number supersession data Continued. PIN designator AA597

38、89/26 Vendor similar designator or type part number 1/ CAGE 61081 Vendor similar designator or type part number 1/ CAGE 5BG68 LE58M VEN2657.80TM2.5LK 5265VEN7.80TM2.5LK LE80R VEN2657.80HLK 5265VEN7.80HLK LE80S VEN2657.80T2LK 5265VEN7.80T2LK LE80T VEN2657.80T0LK 5265VEN7.80T0LK LE80U VEN2657.80TM2LK

39、5265VEN7.80TM2LK DE80M VEN2657.80ETM2.5LK 5265VEN7.80ETM2.5LK DE80S VEN2657.80EHLK 5265VEN7.80EHLK DE80R VEN2657.80ET2LK 5265VEN7.80ET2LK DE80T VEN2657.80ET0LK 5265VEN7.80ET0LK DE80U VEN2657.80ETM2LK 5265VEN7.80ETM2LK CH80M VHA2657.80TM2.5K 5265VBH7.80TM2.5K CH80R VHA2657.80HK 5265VBH7.80HK CH80S VH

40、A2657.80T2K 5265VBH7.80T2K CH80T VHA2657.80T0K 5265VBH7.80T0K CH80U VHA2657.80TM2K 5265VBH7.80TM2K EH80M VHA2657.80ETM2.5K 5265VBH7.80ETM2.5K EH80R VHA2657.80EHK 5265VBH7.80EHK EH80S VHA2657.80ET2K 5265VBH7.80ET2K EH80T VHA2657.80ET0K 5265VBH7.80ET0K EH80U VHA2657.80ETM2K 5265VBH7.80ETM2K LH80M VHA2

41、657.80TM2.5LK 5265VBH7.80TM2.5LK LH80R VHA2657.80HLK 5265VBH7.80HLK LH80S VHA2657.80T2LK 5265VBH7.80T2LK LH80T VHA2657.80T0LK 5265VBH7.80T0LK LH80U VHA2657.80TM2LK 5265VBH7.80TM2LK DH80M VHA2657.80ETM2.5LK 5265VBH7.80ETM2.5LK DH80S VHA2657.80EHLK 5265VBH7.80EHLK DH80R VHA2657.80ET2LK 5265VBH7.80ET2L

42、K DH80T VHA2657.80ET0LK 5265VBH7.80ET0LK DH80U VHA2657.80ETM2LK 5265VBH7.80ETM2LK See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59789/26 8 TABLE III. Commercial part number supersession data Continued. 1/ The manufa

43、cturers part number shall not be used for procurement to the requirements of this CID specification sheet. At the time of preparation of this CID specification sheet, the aforementioned commercial products were reviewed and could be replaced by the CID PIN shown. For actual part marking requirements

44、, see the marking paragraph in AA59789. TABLE IV. Example of PIN with available length designators. PIN designator AA59789/26 Vendor similar designator or type part number 1/ 2/ CAGE 61081 Vendor similar designator or type part number 1/ 2/ CAGE 5BG68 DE30T EN2652.80ET0LK 5265EN2.80ET0LK DE40T EN265

45、3.80ET0LK 5265EN3.80ET0LK DE50T EN2654.80ET0LK 5265EN4.80ET0LK DE60T EN2655.80ET0LK 5265EN5.80ET0LK DE70T EN2656.80ET0LK 5265EN6.80ET0LK DE80T EN2657.80ET0LK 5265EN7.80ET0LK DE90T EN2658.80ET0LK 5265EN8.80ET0LK 1/ The manufacturers part number shall not be used for procurement to the requirements of

46、 this CID specification sheet. At the time of preparation of this CID specification sheet, the aforementioned commercial products were reviewed and could be replaced by the CID PIN shown. For actual part marking requirements, see the marking paragraph in AA59789. 2/ Other lengths are available on re

47、quest. MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: Custodians: GSA FAS Army CR Navy EC Preparing activity: Air Force 85 DLA CC DLA CC Project 59982011026 Review activity: Air Force 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-