DLA A-A-59832 1 A-2011 EXTRACTOR ELECTRICAL CARD METAL NON鈥揕OCKING SINGLE ACTION FOR 鈥淯鈥 CHANNEL ACTUATING SURFACES FOR 032 063 094 AND 125 INCH THICK CIRCUIT CARD ASSEMBLIES.pdf

1、INCHPOUND AA59832/1A 1 February 2011 SUPERSEDING AA59832/1 2 October 2009 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET EXTRACTOR, ELECTRICAL CARD, METAL, NONLOCKING, SINGLE ACTION, FOR “U” CHANNEL ACTUATING SURFACES, FOR .032, .063, .094, AND .125 INCH THICK CIRCUIT CARD ASSEMBLIES The General Se

2、rvices Administration has authorized the use of this commercial item description for all federal agencies. The complete requirements for procuring extractors described herein shall consist of this document and the latest issue in effect of AA59832. CLASSIFICATION/PART IDENTIFICATION NUMBER (PIN). Th

3、is commercial item description (CID) specification sheet uses a classification system which is included in the Part Identification Number (PIN) as shown in the following example (see notes herein). AA59832 CID number /01 Applicable CID sheet * Configuration (see table I) * Slot width (see table I) 1

4、 Material * Finish * Color Example: AA59832/01AS1HB is the PIN for a medium length aluminum extractor designed for mounting on a circuit card assembly with a printed board thickness of .063 inch (1.60 mm) in width. The corrosion protection finish applied to the extractor is black hard anodize. SALIE

5、NT CHARACTERISTICS. Performance. Extractors shall be capable of injecting and removing the circuit card assembly from its installed position. Interface and physical dimensions. The extractors supplied to this CID specification sheet shall be as specified herein and meet the general requirements spec

6、ified in CID AA59832. Configuration. The configuration of a extractor shall be as specified in table I and on figure 1. Slot width. The available slot widths needed to accommodate various printed board thicknesses for the extractors covered by this CID specification sheet are specified in table I. M

7、aterial. The extractor body shall be aluminum alloy 6061, temper T6 as specified in AA59832. The material designator shall be a “1“ as specified in AA59832. Finish. The finish designator shall be as specified in AA59832. The finishes available for this CID specification sheet are as follows: “A“ (an

8、odize) or “L“ (low resistance chemical film). Color. The color designator shall be as specified in AA59832. The colors available for this CID specification sheet are as follows: “B“ (black) or “R“ (red) for anodize finishes and “C“ (clear) or “G“ (gold) for low resistance chemical film. AMSC N/A FSC

9、 5998 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59832/1A 2 Roll pin. A stainless steel roll pin is furnished with each extractor. The roll pin is .09375 inch (2.38 mm) diameter by .3125 inch (7.9 mm) long. TABLE I. Configurations and dimensio

10、ns. 1/ Configuration Slot width designator Slot width dimension “W“ 2/ Inch (mm) Accommodates printed board thickness Inch (mm) Figure A F .048 (1.22) .032 (0.79) 1 A S .080 (2.03) .063 (1.6) A T .110 (2.79) .094 (2.4) A E .140 (3.56) .125 (3.2) 1/ Dimensions are in inches. Millimeters, in parenthes

11、is, are given for general information only. 2/ Tolerance is +.010, .000 inch (+0.25, 0.000 mm). Inches mm Inches mm Inches mm Inches mm .050 .156 1.27 3.96 .312 .325 7.93 8.26 .340 .440 8.64 11.17 .596 1.70 15.14 43.2 NOTES: 1. Dimensions are in inches. Millimeter equivalents are given for general i

12、nformation only. 2. Unless otherwise specified, tolerances are .02 inch (0.51 mm) for two place decimals and .010 inch (0.25 mm) for three place decimals. FIGURE 1. Configuration A dimensions (approximate mechanical advantage of 5.5:1). Provided by IHSNot for ResaleNo reproduction or networking perm

13、itted without license from IHS-,-,-AA59832/1A 3 APPLICATION DATA. Card cage actuating surface. It is recommended that the outer edge of the circuit card assembly be flush with the end of the card guide for the ejector to obtain optimum leverage. The nominal position of card edge when seated in the c

14、onnector is shown on figure 2. The extractor will allow .030 inch (0.8 mm) over travel for tolerance take-up. The circuit card assembly is ejected from its installed position by lever action of the ejector against the “U“ channel. A single ejector is recommended for circuit card assemblies up to 5 i

15、nches (127 mm) in width. For circuit card assemblies over 5 inches (127 mm) in width, or when using an electrical connector with more than 100 contacts, two ejectors mounted on each circuit card assembly is recommended. Inches mm Inches mm Inches mm .030 .03 0.76 0.8 .090 .109 2.29 2.77 .110 .17 2.7

16、9 4.3 NOTES: 1. Dimensions are in inches. Millimeter equivalents are given for general information only. 2. Unless otherwise specified, tolerances are .02 inch (0.51 mm) for two place decimals and .010 inch (0.25 mm) for three place decimals. FIGURE 2. Circuit card assembly to card cage dimensions.

17、Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59832/1A 4 Circuit card assembly printed board. The circuit card assembly should be designed so that electronic components in the area around the ejector mounting hole have sufficient clearance for ej

18、ector rotation as shown on figure 3. Inches mm Inches mm Inches mm .10 .109 2.5 2.77 .180 .310 4.57 7.87 .37 .70 9.4 17.8 NOTES: 1. Dimensions are in inches. Millimeter equivalents are given for general information only. 2. Unless otherwise specified, tolerances are .02 inch (0.51 mm) for two place

19、decimals and .010 inch (0.25 mm) for three place decimals. FIGURE 3. Printed board clearance zone and mounting hole dimensions. NOTES. PIN. The PIN should be used for Government purposes to buy commercial products to this CID specification sheet. See the classification section for PIN format example

20、. Source of documents. Commercial Item Description AA59832 Extractor, Electrical Card, Metal, General Requirements For. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or https:/assist.daps.dla.mil/ or from the Standardization Document Order Desk, 700 Robbi

21、ns Avenue, Building 4D, Philadelphia, PA 191115094.) Ordering data. Ordering data is as specified in AA59832. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59832/1A 5 Commercial products. As part of the market analysis and research effort, this C

22、ID specification sheet was coordinated with the following manufacturers of commercial products. At the time of CID specification sheet preparation and coordination, these manufacturers were known to have commercial products that would meet the requirements of this CID specification sheet. (NOTE: Thi

23、s information should not be considered as a list of approved manufacturers or be used to restrict procurement to only the manufacturers shown.) Manufacturer CAGE Manufacturer name and address Manufacturer contact information 61081 Calmark A Division of Pentair Technical Products 7328 Trade Street Sa

24、n Diego, CA 921213410 Telephone: (858) 7402400 Toll Free: (800) 8547086 Facsimile: (858) 7402430 Electronic mail: URL: 5BG68 Card Locks Unlimited, Inc. 2310 E. Orangethorpe Avenue Anaheim, CA 928061231 Telephone: (714) 7386194 Facsimile: (714) 4460119 E-mail: URL: Part number (P/N) supersession

25、data. This CID specification sheet PINs supersedes the following manufacturers P/Ns as shown in table II. This information is being provided to assist in reducing proliferation in the Government inventory system. TABLE II. Commercial part number supersession data. PIN designator AA59832/01 Vendor si

26、milar designator or type part number 1/ CAGE 5BG68 Vendor similar designator or type part number 1/ CAGE 61081 AF1AB 17351BA AS1AB 17352BA 10735 AT1AB 17353BA 107353 AE1AB 17354BA 107354 AF1AR 17351RA AS1AR 17352RA AT1AR 17353RA AE1AR 17354RA AF1CC 17351CC AS1CC 17352CC C10735 AT1CC 17353CC C107353

27、AE1CC 17354CC C107354 AF1CG 17351CG AS1CG 17352CG AT1CG 17353CG AE1CG 17354CG 1/ The manufacturers P/N shall not be used for procurement to the requirements of this CID specification sheet. At the time of preparation of this CID specification sheet, the aforementioned commercial products were review

28、ed and could be replaced by the CID PIN shown. For actual part marking requirements, see the marking paragraph in AA59832. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59832/1A 6 Changes from previous issue. Marginal notations are not used in th

29、is revision to identify changes with respect to the previous issue due to the extensiveness of the changes. MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: Custodians: GSA FAS Army CR Navy EC Air Force 85 Preparing Activity: DLA CC DLA CC Review Activity: Project: 59982010051 Air Force 99 NO

30、TE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-