DLA A-A-59832 3 A-2011 EXTRACTOR ELECTRICAL CARD METAL LOCKING SINGLE ACTION FOR 鈥淯鈥 CHANNEL ACTUATING SURFACES FOR 063 094 AND 125 INCH THICK CIRCUIT CARD ASSEMBLIES.pdf

1、INCHPOUND AA59832/3A 3 February 2011 SUPERSEDING AA59832/3 2 October 2009 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET EXTRACTOR, ELECTRICAL CARD, METAL, LOCKING, SINGLE ACTION, FOR “U” CHANNEL ACTUATING SURFACES, FOR .063, .094, AND .125 INCH THICK CIRCUIT CARD ASSEMBLIES The General Services Ad

2、ministration has authorized the use of this commercial item description for all federal agencies. The complete requirements for procuring extractors described herein shall consist of this document and the latest issue in effect of AA59832. CLASSIFICATION/PART IDENTIFICATION NUMBER (PIN). This commer

3、cial item description (CID) specification sheet uses a classification system which is included in the Part Identification Number (PIN) as shown in the following example (see notes). AA59832 CID number /03 Applicable CID sheet * Configuration (see table I) * Slot width (see table I) 1 Material * Fini

4、sh * Color Example: AA59832/03BE1LC is the PIN for a long length aluminum extractor designed for mounting on a circuit card assembly with a printed board thickness of .125 inch (3.20 mm) in width. The corrosion protection finish applied to the extractor is clear low resistance chemical film. SALIENT

5、 CHARACTERISTICS. Performance. Extractors shall be capable of injecting and removing the circuit card assembly from its installed position. Interface and physical dimensions. The extractors supplied to this CID specification sheet shall be as specified herein and meet the general requirements specif

6、ied in CID AA59832. Configuration. The configuration of a extractor shall be as specified in table I. The details of a particular configuration consist of those on figures 1 and 2. Slot width. The available slot widths needed to accommodate various printed board thicknesses for the extractors covere

7、d by this CID specification sheet are specified in table I. Material. The extractor body shall be aluminum alloy 6061, temper T6 as specified in AA59832. The material designator shall be a “1“ as specified in AA59832. Finish. The finish designator shall be as specified in AA59832. The finishes avail

8、able for this CID specification sheet are as follows: “A“ (anodize) or “L“ (low resistance chemical film). Color. The color designator shall be as specified in AA59832. The colors available for this CID specification sheet are as follows: “B“ (black) or “R“ (red) for anodize finishes and “C“ (clear)

9、 or “G“ (gold) for low resistance chemical film. AMSC N/A FSC 5998 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59832/3A 2 Roll pin. A stainless steel roll pin is furnished with each extractor. The roll pin is .09375 inch (2.38 mm) diameter by .

10、3125 inch (7.9 mm) long. TABLE I. Configurations and dimensions. 1/ Configuration Slot width designator Slot width dimension “W“ 2/ Inch (mm) Accommodates printed board thickness Inch (mm) Figure B S .080 .063 (1.6) 1 B T .110 .094 (2.4) B E .140 .125 (3.2) C S .080 .063 (1.6) 2 C T .110 .094 (2.4)

11、C E .140 .125 (3.2) 1/ Dimensions are in inches. Millimeters, in parenthesis, are given for general information only. 2/ Tolerance is +.010, .000 inch (+0.25, 0.000 mm). Inches mm Inches mm Inches mm .290 .475 7.37 12.07 .500 .88 12.7 22.35 1.87 2.00 47.49 50.8 NOTES: 1. Dimensions are in inches. Mi

12、llimeter equivalents are given for general information only. 2. Unless otherwise specified, tolerances are .02 inch (0.51 mm) for two place decimals and .010 inch (0.25 mm) for three place decimals. FIGURE 1. Configuration B dimensions (approximate mechanical advantage of 4.2:1). Provided by IHSNot

13、for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59832/3A 3 Inches mm Inches mm Inches mm .290 .475 7.37 12.07 .500 .88 12.7 22.35 2.00 3.25 50.8 82.55 NOTES: 1. Dimensions are in inches. Millimeter equivalents are given for general information only. 2. Unless otherwi

14、se specified, tolerances are .02 inch (0.51 mm) for two place decimals and .010 inch (0.25 mm) for three place decimals. FIGURE 2. Configuration C dimensions (approximate mechanical advantage of 7:1). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A

15、A59832/3A 4 APPLICATION DATA. Card cage actuating surface. The nominal position of circuit card assembly edge to the “U“ channel edge when seated in the connector is shown on figure 3. The extractor will allow .05 inch (1.3 mm) over travel for tolerance take-up. The circuit card assembly is ejected

16、from its installed position by lever action of the ejector against the “U“ channel of the card cage. A single ejector is recommended for circuit card assemblies up to 5 inches (127 mm) in width. For circuit card assemblies over 5 inches (127 mm) in width, or when using an electrical connector with m

17、ore than 100 contacts, two ejectors mounted on each circuit card assembly is recommended. Inches mm Inches mm Inches mm Inches mm Inches mm .015 .05 0.38 1.3 .06 .109 1.5 2.77 .24 .250 6.1 6.35 .285 .36 7.24 9.1 .73 18.5 NOTES: 1. Dimensions are in inches. Millimeter equivalents are given for genera

18、l information only. 2. Unless otherwise specified, tolerances are .02 inch (0.51 mm) for two place decimals and .010 inch (0.25 mm) for three place decimals. FIGURE 3. Circuit card assembly printed board mounting dimensions. Provided by IHSNot for ResaleNo reproduction or networking permitted withou

19、t license from IHS-,-,-AA59832/3A 5 Circuit card assembly printed board. The circuit card assembly should be designed so that electronic components in the area around the ejector mounting hole have sufficient clearance for ejector rotation as shown on figure 4. Inches mm Inches mm Inches mm Inches m

20、m .005 .090 0.13 2.29 .094 .109 2.39 2.77 .250 .36 6.35 9.14 .73 .900 18.5 22.86 NOTES: 1. Dimensions are in inches. Millimeter equivalents are given for general information only. 2. Unless otherwise specified, tolerances are .02 inch (0.51 mm) for two place decimals and .010 inch (0.25 mm) for thre

21、e place decimals. FIGURE 4. Printed board clearance zone and mounting hole dimensions. NOTES. PIN. The PIN should be used for Government purposes to buy commercial products to this CID specification sheet. See the classification section for PIN format example. Source of documents. Commercial Item De

22、scription AA59832 Extractor, Electrical Card, Metal, General Requirements For. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or https:/assist.daps.dla.mil/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA

23、191115094.) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59832/3A 6 Ordering data. Ordering data is as specified in AA59832. Commercial products. As part of the market analysis and research effort, this CID specification sheet was coordinated wi

24、th the following manufacturers of commercial products. At the time of CID specification sheet preparation and coordination, these manufacturers were known to have commercial products that would meet the requirements of this CID specification sheet. (NOTE: This information should not be considered as

25、 a list of approved manufacturers or be used to restrict procurement to only the manufacturers shown.) Manufacturer CAGE Manufacturer name and address Manufacturer contact information 61081 Calmark A Division of Pentair Technical Products 7328 Trade Street San Diego, CA 921213410 Telephone: (858) 74

26、02400 Toll Free: (800) 8547086 Facsimile: (858) 7402430 Electronic mail: URL: 5BG68 Card Locks Unlimited, Inc. 2310 E. Orangethorpe Avenue Anaheim, CA 928061231 Telephone: (714) 7386194 Facsimile: (714) 4460119 E-mail: URL: Part number (P/N) supersession data. This CID specification sheet PINs s

27、upersedes the following manufacturers P/Ns as shown in table II. This information is being provided to assist in reducing proliferation in the Government inventory system. TABLE II. Commercial P/N supersession data. PIN designator AA59832/03 Vendor similar designator or type part number 1/ CAGE 5BG6

28、8 Vendor similar designator or type part number 1/ CAGE 61081 BS1AB 17732BA 10773 BT1AB 17733BA 107733 BE1AB 17734BA 107734 BS1AR 17732RA BT1AR 17733RA BE1AR 17734RA BS1LC 17732CC C10773 BT1LC 17733CC C107733 BE1LC 17734CC C107734 BS1LG 17732CG BT1LG 17733CG BE1LG 17734CG See footnote at end of tabl

29、e. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59832/3A 7 TABLE II. Commercial P/N supersession data. PIN designator AA59832/03 Vendor similar designator or type part number 1/ CAGE 5BG68 Vendor similar designator or type part number 1/ CAGE 61

30、081 CS1AB 17752BA 10775 CT1AB 17753BA 107753 CE1AB 17754BA 107754 CS1AR 17752RA CT1AR 17753RA CE1AR 17754RA CS1LC 17752CC C10775 CT1LC 17753CC C107753 CE1LC 17754CC C107754 CS1LG 17752CG CT1LG 17753CG CE1LG 17754CG 1/ The manufacturers P/N shall not be used for procurement to the requirements of thi

31、s CID specification sheet. At the time of preparation of this CID specification sheet, the aforementioned commercial products were reviewed and could be replaced by the CID PIN shown. For actual part marking requirements, see the marking paragraph in AA59832. Changes from previous issue. Marginal no

32、tations are not used in this revision to identify changes with respect to the previous issue due to the extensiveness of the changes. MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: Custodians: GSA FAS Army CR Navy EC Air Force 85 Preparing Activity: DLA CC DLA CC Review Activity: Project: 5

33、9982010053 Air Force 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-