DLA A-A-59856-2010 ANCHOR ROCK CAMMING DEVICE TYPE I REPAIR KIT.pdf

1、 A-A-59856 12 January 2010 COMMERICAL ITEM DESCRIPTION ANCHOR, ROCK, CAMMING DEVICE, TYPE I, REPAIR KIT The General Services Administration has authorized the use of this commercial item description, for all federal agencies. 1. SCOPE. This commercial item description covers the requirements for roc

2、k anchor camming device repair kits, also referred to as spring loaded camming device (SLCD) trigger kits, which are used to repair the trigger wires on SLCDs. 2. CLASSIFICATION. The SLCD repair kit will be furnished to repair all sizes of Anchor, Rock, Camming Device, Type I, as specified in accord

3、ance with A-A-59846. 3. SALIENT CHARACTERISTICS. The repair kit shall be two wires in each kit, designed to replace the wires that connect the trigger mechanism to the cam lobe enabling user level repair while meeting the standards in this description. 3.1 Color. The wires shall be provided in a low

4、 reflectance, matte finish and provide low contrast with typical use terrain unless otherwise specified in the solicitation or contract order (see 7.2). 3.2 Materials. 3.2.1 Basic material. Steel. 3.3 Tests. The SLCD, when the repair kit wires are installed, shall meet EN 12276 and the International

5、 Mountaineering and Climbing Federation Union Internationale des Associations dAlpinisme (UIAA) Standard 125. Comments, suggestions, or questions on this document should be addressed to: Defense Supply Center Philadelphia, Clothing and Textiles Directorate, Attn: DSCP Standardization Team, 700 Robbi

6、ns Avenue, Philadelphia, PA 19111-5096. Since contact information can change, you may want to verify the currency of this address information using Acquisition Streamlining and Standardization Information System (ASSIST) online database at http:/assist.daps.dla.mil/ . AMSC N/A FSC 8465 METRIC Provid

7、ed by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59856 2 3.4 Workmanship. The finished anchor, rock, camming, device, Type I repair kit shall conform to the quality of product established by this document. The occurrence of defects shall not exceed the

8、contractors own quality assurance standards and the quality assurance standards defined in the technical data in the solicitation and/or contract. 3.5 Service life. The anchor, rock, camming, device, Type I repair kit shall have no unexpected material or component failures during a continuous one-ye

9、ar cycle. The Type I repair kit shall have no unexpected material or component failures during periodic use over a five year period. 3.6 Labels/barcoding/instruction slip. If applicable, all labeling, barcoding and instruction slip requirements shall be as specified in the solicitation or contract (

10、see 7.2). 3.6.1 Labels. Each anchor rock camming device repair kit shall have identification label Class 5 conforming to Type VI of MIL-DTL-32075. The color of the label shall be white. The following information shall be included in the printing for the identification label for the anchor rock cammi

11、ng device repair kit. ANCHOR, ROCK, CAMMING DEVICE, TYPE I REPAIR KIT NSN: XXXX-XX-XXX-XXXX 4. REGULATORY REQUIREMENTS. The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR).

12、4.1 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible, provided that the material meets or exceeds the operational and maintenance requirements and promotes economically advantageou

13、s life cycle costs. 5. PRODUCT CONFORMANCE PROVISIONS. 5.1 Product conformance. The products provided shall meet the salient characteristics of this Commercial Item Description, conform to the producers own drawings, specifications, standards, and quality assurance practices, and be the same product

14、 offered for sale in the commercial marketplace. The Government reserves the right to require proof of such conformance. 5.2 Visual examination. Each anchor rock camming device Type I repair kit shall be examined for the following defects as listed in Table I. Provided by IHSNot for ResaleNo reprodu

15、ction or networking permitted without license from IHS-,-,-A-A-59856 3 TABLE I. End item examination Examine Defect Description Finish Not smooth and adherent Not low reflectance matte finish Does not provide low contrast with typical use terrain Construction Not free of burrs, rough spots, slivers,

16、 flat areas or projections Any component loose, missing or not specified type Any component fractured, slit, punctured, dented, bowed, malformed or damaged Marking etched or indented, contains rough or sharp edges Labels/barcoding/instruction slip (if applicable) Incorrect, illegible, omitted or mis

17、placed Marking Omitted, missing information or illegible 5.3 Acceptance criteria. Acceptance criteria shall be as specified in the contract or purchase order (see 7.2). 6. PACKAGING. 6.1 Preservation, packing and marking. The preservation, packing and marking shall be as specified in the contract or

18、 order (see 7.2). 7. NOTES. 7.1 Sources of documents. 7.1.1 Government documents. Copies of Government documents are available online at http:/assist.daps.dla.mil/quicksearch/ or from the Standardization Documents Order Desk, Building 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094. DRAWINGS U.S

19、 ARMY NATICK SOLDIER CENTER 3-3-0120 Anchor, Rock, Camming Device, Type I Repair Kit (Copies of drawings are available from the U.S. Army Natick Research Development and Engineering Center, Natick Soldier Center, ATTN: NSRDEC-RDNS-WPW-C, Natick, MA 01760) Provided by IHSNot for ResaleNo reproductio

20、n or networking permitted without license from IHS-,-,-A-A-59856 4 7.1.2 Federal Acquisition Regulations are available online at http:/acquisition.gov/far/index.html or by contacting the Superintendent of Documents at 202-512-1800. 7.1.3 Non-Government documents. Non-Government standards and other p

21、ublications are normally available from the organizations that prepare or distribute the documents. These documents may be available in or through libraries or other informational services. EUROPEAN STANDARD (EN) EN 12276: Mountaineering Equipment Frictional Anchors Safety Requirements and Test Meth

22、ods (Copies are available online at www.bsi- or from BSI British Standards, Customer Services 389 Chiswick High Road London W4 4AL United Kingdom) INTERNATIONAL MOUNTAINEERING AND CLIMBING FEDERATION UNION INTERNATIONALE DES ASSOCIATIONS DALPINISME (UIAA) UIAA Safety Standard 125 Mountaineering and

23、Climbing Equipment, Frictional Anchors (Copies are available online at http:/www.theuiaa.org or from the Union Internationale Des Associations DAlpinisme (UIAA) Monbijoustrasse 61 Postfach CH-3000 Bern 23 Switzerland 7.2 Ordering Data. The contract or order should specify the following: a. Title, nu

24、mber, and date of this Commercial Item Description. b. Type, size and color required (see 2 and 3.1). c. When required, labeling, barcoding, and instruction slip (see 3.6). d. Acceptance criteria (see 5.3). e. Packaging (see 6.1). 7.3 Key words. Climbing Protection MILITARY INTERESTS: CIVIL AGENCY C

25、OORDINATING ACTIVITY: GSA FSS Custodian: PREPARING ACTIVITY: Army - GL DLA-CT Marine Corps MC Project 8465-2009-003 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using ASSIST Online database at http:/assist.daps.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-