DLA A-A-59935 2-2013 CONICAL SEALS CRUSH 37 DEGREE FLARED TUBE FITTTING COPPER.pdf

1、 INCHPOUND AA59935/2 2 October 2013 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET CONICAL SEALS, CRUSH, 37 DEGREE FLARED TUBE FITTTING, COPPER The General Services Administration has authorized the use of this commercial item description for all federal agencies. The complete requirements for proc

2、uring conical seal, crush, 37 degree flared tube fitting, copper described herein shall consist of this document and the issue in effect of A-A-59935. CLASSIFICATION/PART OR IDENTIFICATION NUMBER (PIN). This commercial item description (CID) uses a classification system which is included in the PIN

3、as shown in the following example (see NOTES). AA59935/2 -04 C CID number Size code (see figure 1) Material and finish code (see table I) SALIENT CHARACTERISTICS. Interface and physical dimensions. Conical seals, crush, 37 degree flared tube fitting, copper supplied to this CID specification sheet s

4、hall be as specified herein (see figure 1 and table I). Beneficial comments, recommendations, additions, deletions, clarifications, etc., and any data that may improve this document should be sent to: DLA Land and Maritime, ATTN: VAI, P.O. Box 3990, Columbus OH 432180-3990, or fluidflowdla.mil. Sinc

5、e contact information can change you may want to verify the currency of the address information using the ASSIST Online database at https:/assist.dla.mil/. AMSC N/A FSC 4730Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59935/2 2 Dash size code

6、Tubing OD Ref. A +.005 -.000 B +.000 -.015 C +.005 -.000 D +.015 -.000 T inch -02 1/8 .240 .060 .245 .103 .005 -03 3/16 .302 .307 .166 -04 1/4 .354 .075 .359 .213 -05 5/16 .416 .421 .275 -06 3/8 .471 .476 .338 -08 1/2 .649 .095 .654 .446 .010 -10 5/8 .762 .105 .767 .562 -12 3/4 .933 .938 .687 -16 1

7、1.183 .125 1.188 .936 -20 1-1/4 1.496 1.501 1.375 -24 1-1/2 1.745 1.750 1.410 -28 1-3/4 2.120 2.125 1.680 -32 2 2.370 2.375 1.913 -40 2 1/2 2.877 .055 2.882 2.500 .015 -44 2 3/4 3.127 3.125 2.742 -48 3 3.377 3.382 2.990 NOTES: 1. Dimensions are in inches. 2. Dimensioning and tolerancing in accordanc

8、e with ASME Y14.5. Unless otherwise specified, tolerances for decimals .005 inch (0.13 mm), angles .5. 3. Break sharp edges and remove burrs and slivers. 4. Surface texture shall be .005 inches in accordance with ASME B46.1. 5. These parts are soft and easily deformed dimensions B, C, and D shall be

9、 verified by installing the seal on a standard fitting of the appropriate size. 6. An out-of-round-seal that does not interfere with installation shall not be cause for rejection. FIGURE 1. 37 flared crush seal. Provided by IHSNot for ResaleNo reproduction or networking permitted without license fro

10、m IHS-,-,-A-A-59935/2 3 TABLE I. Material and finish code. Material and finish code Material and finish C Copper foil or strip, annealed, type C10100, C10200 or C11000 in accordance with ASTM B152/B152M CT Copper foil or strip, annealed, type C10100, C10200 or C11000 in accordance with ASTM B152/B15

11、2M Tin plated in accordance with ASTM B545 or SAE-AMS2408 Tubing material and fluids or gases to be sealed, see table II. TABLE II. Tubing material and fluids or gases. Tubing and fitting material Assembly temperature range Fluid or gases Steel -420F to +800F (-251C to 427C) Helium Hydraulic oil (no

12、n-sulphur) Hydrogen Hydrazine JP-4 JP-5 Nitrogen Oxygen Pneumatics Torque technique. These seals require a second torque technique; see A-A-59935 for torqueing procedure. NOTES. PIN. The PIN should be used for Government purposes to buy commercial products to this CID specification sheet. See the cl

13、assification section for PIN format example. Source of documents. COMMERCIAL ITEM DESCRIPTIONS A-A-59935 - Conical Seal, Crush, 37 Degree Flared Tube Fitting, General Requirements For (Copies of these documents are available online at http:/quicksearch.dla.mil/ or from the DLA Document Services Orde

14、r Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 191115094). Other Publications Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59935/2 4 ASME INTERNATIONAL ASME Y14.5 - Dimensioning and Tolerancing ASME B46.1 - Surface Texture (Surface

15、Roughness, Waviness, and Lay) (Copies of these documents are available online at http:/www.asme.org or from the ASME International, Three Park Avenue, New York, NY 10016-5990.) ASTM INTERNATIONAL ASTM B152/B152M - Standard Specification for Copper Sheet, Strip, Plate, and Rolled Bar ASTM B545 - Stan

16、dard Specification for Electrodeposited Coatings of Tin (Copies of these documents are available online at http:/www.astm.org or from the ASTM International, P.O. Box C700, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.) SAE INTERNATIONAL SAE-AMS2408 - Plating, Tin (Copies of these documen

17、ts are available on line at www.sae.org from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, and Tel: 877-606-7323 inside USA and Canada or 724-776-4970 outside USA, email at CustomerServicesae.org.) Commercial products. As part of the market analysis and research effort, this

18、CID specification sheet was coordinated with the following manufacturers of commercial products. At the time of CID specification sheet preparation and coordination, these manufacturers were known to have commercial products that would meet the requirements of this CID specification sheet. (NOTE: Th

19、is information should not be considered as a list of approved manufacturers or be used to restrict acquisition to only the manufacturers shown.) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59935/2 5 MFRs CAGE number MFRs name and address 3344

20、7 SECO Seals Inc. 1370 Logan Ave. Unit K Costa Mesa, CA 92626 714-546-3778 E-mail: 64162 Del Aerospace, Inc. 921 Mountain View Ave A Oxnard, CA 93030-7227 E-mail: 66776 Alcoa Global Fasteners Inc. Div Rosan / Eagle Products DBA Alcoa Fastening Systems 800 S State College Blvd Fullerton, CA 92831-5

21、334 01673 SPS Technologies LLC DBA Airdrome Precision Components Div SPS Technologies LLC 3251 E Airport WY Long Beach, CA 90806-2407 Part number (P/N) supersession data. These CID specification sheet PINs supersede the following MFRs P/Ns as shown. This information is being provided to assist in re

22、ducing proliferation in the Government inventory system (see table III). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59935/2 6 TABLE III. P/N supersession data. Dash number (see table I) AA59935 MFRs CAGE MFRs P/N 1/ MFRs CAGE MFRs P/N 1/ -02

23、C 33447 SECO7C-02 64162 DY90-C-2 -03C 33447 SECO7C-03 64162 DY90-C-3 -04C 33447 SECO7C-04 64162 DY90-C-4 -05C 33447 SECO7C-05 64162 DY90-C-5 -06C 33447 SECO7C-06 64162 DY90-C-6 -08C 33447 SECO7C-08 64162 DY90-C-8 -10C 33447 SECO7C-10 64162 DY90-C-10 -12C 33447 SECO7C-12 64162 DY90-C-12 -16C 33447 SE

24、CO7C-16 64162 DY90-C-16 -20C 33447 SECO7C-20 64162 DY90-C-20 -24C 33447 SECO7C-24 64162 DY90-C-24 -28C 33447 SECO7C-28 64162 DY90-C-28 -32C 33447 SECO7C-32 64162 DY90-C-32 -40C 33447 SECO7C-40 64162 DY90-C-40 -44C 33447 SECO7C-44 64162 DY90-C-44 -48C 33447 SECO7C-48 64162 DY90-C-48 Dash number (see

25、table I) AA59935 MFRs CAGE MFRs P/N 1/ MFRs CAGE MFRs P/N 1/ -02C 66776 VSF1015C2 01673 AP50C2 -03C 66776 VSF1015C3 01673 AP50C3 -04C 66776 VSF1015C4 01673 AP50C4 -05C 66776 VSF1015C5 01673 AP50C5 -06C 66776 VSF1015C6 01673 AP50C6 -08C 66776 VSF1015C8 01673 AP50C8 -10C 66776 VSF1015C10 01673 AP50C10

26、 -12C 66776 VSF1015C12 01673 AP50C12 -16C 66776 VSF1015C16 01673 AP50C16 -20C 66776 VSF1015C20 01673 AP50C20 -24C 66776 VSF1015C24 01673 AP50C24 -28C 66776 VSF1015C28 01673 AP50C28 -32C 66776 VSF1015C32 01673 AP50C32 -40C 66776 VSF1015C40 01673 AP50C40 -44C 66776 VSF1015C44 01673 AP50C44 -48C 66776

27、VSF1015C48 01673 AP50C48 See note at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59935/2 7 TABLE III. P/N supersession data - Continued. Dash number (see table I) AA59935 MFRs CAGE MFRs P/N 1/ MFRs CAGE MFRs P/N 1/ -02CT 33447 S

28、ECO7CT-02 64162 DY90-CT-2 -03CT 33447 SECO7CT-03 64162 DY90-CT-3 -04CT 33447 SECO7CT-04 64162 DY90-CT-4 -05CT 33447 SECO7CT-05 64162 DY90-CT-5 -06CT 33447 SECO7CT-06 64162 DY90-CT-6 -08CT 33447 SECO7CT-08 64162 DY90-CT-8 -10CT 33447 SECO7CT-10 64162 DY90-CT-10 -12CT 33447 SECO7CT-12 64162 DY90-CT-12

29、 -16CT 33447 SECO7CT-16 64162 DY90-CT-16 -20CT 33447 SECO7CT-20 64162 DY90-CT-20 -24CT 33447 SECO7CT-24 64162 DY90-CT-24 -28CT 33447 SECO7CT-28 64162 DY90-CT-28 -32CT 33447 SECO7CT-32 64162 DY90-CT-32 -40CT 33447 SECO7CT-40 64162 DY90-CT-40 -44CT 33447 SECO7CT-44 64162 DY90-CT-44 -48CT 33447 SECO7CT

30、-48 64162 DY90-CT-48 Dash number (see table I) AA59935 MFRs CAGE MFRs P/N 1/ MFRs CAGE MFRs P/N 1/ -02CT 66776 VSF1015CT2 01673 AP50A2 -03CT 66776 VSF1015CT3 01673 AP50*3 -04CT 66776 VSF1015CT4 01673 AP50*4 -05CT 66776 VSF1015CT5 01673 AP50*5 -06CT 66776 VSF1015CT6 01673 AP50*6 -08CT 66776 VSF1015CT

31、8 01673 AP50*8 -10CT 66776 VSF1015CT10 01673 AP50*10 -12CT 66776 VSF1015CT12 01673 AP50*12 -16CT 66776 VSF1015CT16 01673 AP50*16 -20CT 66776 VSF1015CT20 01673 AP50*20 -24CT 66776 VSF1015CT24 01673 AP50*24 -28CT 66776 VSF1015CT28 01673 AP50*28 -32CT 66776 VSF1015CT32 01673 AP50*32 -40CT 66776 VSF1015

32、CT40 01673 AP50*40 -44CT 66776 VSF1015CT44 01673 AP50*44 -48CT 66776 VSF1015CT48 01673 AP50*48 1/ The manufacturers P/N shall not be used for procurement to the requirements of this specification sheet. At the time of preparation of this specification sheet, the aforementioned commercial products we

33、re reviewed and could be replaced by the CID PIN shown. For actual part marking requirements, see the marking paragraph of A-A-59935. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59935/2 8 MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY

34、: Custodians: GSA - FAS Army - AV Navy - AS Air Force - 99 Preparing activity: DLA - CC DLA - CC Review activities: Army - AT, MI Project 4730-2013-077 Navy - MC, SH Air Force - 71 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-