DLA A-A-59935 5-2013 CONICAL SEALS CRUSH 37 DEGREE FLARED TUBE FITTING GOLD.pdf

1、 INCHPOUND AA59935/5 2 October 2013 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET CONICAL SEALS, CRUSH, 37 DEGREE FLARED TUBE FITTING, GOLD The General Services Administration has authorized the use of this commercial item description for all federal agencies. The complete requirements for procuri

2、ng conical seal, crush, 37 degree flared tube fitting, gold described herein shall consist of this document and the issue in effect of A-A-59935. CLASSIFICATION/PART OR IDENTIFICATION NUMBER (PIN). This commercial item description (CID) uses a classification system which is included in the PIN as sh

3、own in the following example (see NOTES). AA59935/5 -04 G CID number Size code (see figure 1) Material and finish code (see table I) SALIENT CHARACTERISTICS. Interface and physical dimensions. Conical seals, crush, 37 degree flared tube fitting, gold supplied to this CID specification sheet shall be

4、 as specified herein (see figure 1 and table I). Beneficial comments, recommendations, additions, deletions, clarifications, etc., and any data that may improve this document should be sent to: DLA Land and Maritime, ATTN: VAI, P.O. Box 3990, Columbus OH 432180-3990, or fluidflowdla.mil. Since conta

5、ct information can change you may want to verify the currency of the address information using the ASSIST Online database at https:/assist.dla.mil/. AMSC N/A FSC 4730Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59935/5 2 Dash size code Tubing

6、OD Ref. A +.005 -.000 B +.000 -.015 C +.005 -.000 D +.015 -.000 T inch -02 1/8 .240 .060 .245 .103 .005 -03 3/16 .302 .307 .166 -04 1/4 .354 .075 .359 .213 -05 5/16 .416 .421 .275 -06 3/8 .471 .476 .338 -08 1/2 .649 .095 .654 .446 .010 -10 5/8 .762 .105 .767 .562 -12 3/4 .933 .938 .687 -16 1 1.183 .

7、125 1.188 .936 -20 1-1/4 1.496 1.501 1.375 -24 1-1/2 1.745 1.750 1.410 -28 1-3/4 2.120 2.125 1.680 -32 2 2.370 2.375 1.913 -40 2 1/2 2.877 .055 2.882 2.500 .015 -44 2 3/4 3.127 3.125 2.742 -48 3 3.377 3.382 2.990 NOTES: 1. Dimensions are in inches. 2. Dimensioning and tolerancing in accordance with

8、ASME Y14.5. Unless otherwise specified, tolerances for decimals .005 inch (0.13 mm), angles .5. 3. Break sharp edges and remove burrs and slivers. 4. Surface texture shall be .005 inches in accordance with ASME B46.1. 5. These parts are soft and easily deformed dimensions B, C, and D shall be verifi

9、ed by installing the seal on a standard fitting of the appropriate size. 6. An out-of-round-seal that does not interfere with installation shall not be cause for rejection. FIGURE 1. 37 flared crush seal. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,

10、-,-A-A-59935/5 3 TABLE I. Material and finish code. Material and finish code Material and finish G Grade 99.99 gold in accordance with ASTM B562 Torque technique. These seals require a second torque technique; see A-A-59935 for torqueing procedure. NOTES. PIN. The PIN should be used for Government p

11、urposes to buy commercial products to this CID specification sheet. See the classification section for PIN format example. Source of documents. COMMERCIAL ITEM DESCRIPTIONS A-A-59935 - Conical Seal, Crush, 37 Degree Flared Tube Fitting, General Requirements For (Copies of these documents are availab

12、le online at http:/quicksearch.dla.mil/ or from the DLA Document Services Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 191115094). Other Publications ASME INTERNATIONAL ASME Y14.5 - Dimensioning and Tolerancing ASME B46.1 - Surface Texture (Surface Roughness, Waviness, and Lay) (Cop

13、ies of these documents are available online at http:/www.asme.org or from the ASME International, Three Park Avenue, New York, NY 10016-5990.) ASTM INTERNATIONAL ASTM B562 - Standard Specification for Refined Gold (Copies of these documents are available online at http:/www.astm.org or from the ASTM

14、 International, P.O. Box C700, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.) Commercial products. As part of the market analysis and research effort, this CID specification sheet was coordinated with the following manufacturers of commercial products. At the time of CID specification she

15、et preparation and coordination, these manufacturers were known to have commercial products that would meet the requirements of this CID specification sheet. (NOTE: This information should not be considered as a list of approved manufacturers or be used to restrict acquisition to only the manufactur

16、ers shown.) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59935/5 4 MFRs CAGE number MFRs name and address 33447 SECO Seals Inc. 1370 Logan Ave. Unit K Costa Mesa, CA 92626 714-546-3778 E-mail: 64162. Del Aerospace, Inc. 921 Mountain View Ave

17、A Oxnard, CA 93030-7227 E-mail: 66776 Alcoa Global Fasteners Inc. Div Rosan / Eagle Products DBA Alcoa Fastening Systems 800 S State College Blvd Fullerton, CA 92831-5334 01673 SPS Technologies LLC DBA Airdrome Precision Components Div SPS Technologies LLC 3251 E Airport WY Long Beach, CA 90806-240

18、7 Part number (P/N) supersession data. These CID specification sheet PINs supersede the following MFRs P/Ns as shown. This information is being provided to assist in reducing proliferation in the Government inventory system (see table II). Provided by IHSNot for ResaleNo reproduction or networking p

19、ermitted without license from IHS-,-,-A-A-59935/5 5 TABLE II. P/N supersession data. Dash number (see table I) AA59935 MFRs CAGE MFRs P/N 1/ MFRs CAGE MFRs P/N 1/ -02G 33447 SECO7G-02 64162 DY90-G-2 -03G 33447 SECO7G-03 64162 DY90-G-3 -04G 33447 SECO7G-04 64162 DY90-G-4 -05G 33447 SECO7G-05 64162 DY

20、90-G-5 -06G 33447 SECO7G-06 64162 DY90-G-6 -08G 33447 SECO7G-08 64162 DY90-G-8 -10G 33447 SECO7G-10 64162 DY90-G-10 -12G 33447 SECO7G-12 64162 DY90-G-12 -16G 33447 SECO7G-16 64162 DY90-G-16 -20G 33447 SECO7G-20 64162 DY90-G-20 -24G 33447 SECO7G-24 64162 DY90-G-24 -28G 33447 SECO7G-28 64162 DY90-G-28

21、 -32G 33447 SECO7G-32 64162 DY90-G-32 -40G 33447 SECO7G-40 64162 DY90-G-40 -44G 33447 SECO7G-44 64162 DY90-G-44 -48G 33447 SECO7G-48 64162 DY90-G-48 Dash number (see table I) AA59935 MFRs CAGE MFRs P/N 1/ MFRs CAGE MFRs P/N 1/ -02G 66776 VSF1015G2 01673 AP50G2 -03G 66776 VSF1015G3 01673 AP50*3 -04G

22、66776 VSF1015G4 01673 AP50G4 -05G 66776 VSF1015G5 01673 AP50*5 -06G 66776 VSF1015G6 01673 AP50*6 -08G 66776 VSF1015G8 01673 AP50*8 -10G 66776 VSF1015G10 01673 AP50*10 -12G 66776 VSF1015G12 01673 AP50*12 -16G 66776 VSF1015G16 01673 AP50*16 -20G 66776 VSF1015G20 01673 AP50*20 -24G 66776 VSF1015G24 016

23、73 AP50*24 -28G 66776 VSF1015G28 01673 AP50*28 -32G 66776 VSF1015G32 01673 AP50*32 -40G 66776 VSF1015G40 01673 AP50*40 -44G 66776 VSF1015G44 01673 AP50*44 -48G 66776 VSF1015G48 01673 AP50*48 1/ The manufacturers P/N shall not be used for procurement to the requirements of this specification sheet. A

24、t the time of preparation of this specification sheet, the aforementioned commercial products were reviewed and could be replaced by the CID PIN shown. For actual part marking requirements, see the marking paragraph of A-A-59935. Provided by IHSNot for ResaleNo reproduction or networking permitted w

25、ithout license from IHS-,-,-A-A-59935/5 6 MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: Custodians: GSA - FAS Army - AV Navy - AS Air Force - 99 Preparing activity: DLA - CC DLA - CC Review activities: Army - AT, MI Project 4730-2013-080 Navy - MC, SH Air Force - 71 NOTE: The activities li

26、sted above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-