DLA A-A-59935 6-2013 CONICAL SEALS CRUSH 37 DEGREE FLARED TUBE FITTING SERRATED.pdf

1、 INCHPOUND AA59935/6 2 October 2013 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET CONICAL SEALS, CRUSH, 37 DEGREE FLARED TUBE FITTING, SERRATED The General Services Administration has authorized the use of this commercial item description for all federal agencies. The complete requirements for pro

2、curing conical seal, crush, 37 degree flared tube fitting, serrated described herein shall consist of this document and the issue in effect of A-A-59935. CLASSIFICATION/PART OR IDENTIFICATION NUMBER (PIN). This commercial item description (CID) uses a classification system which is included in the P

3、IN as shown in the following example (see NOTES). AA59935/6 -04 C CID number Size code (see figure 1) Material and finish code (see table I) SALIENT CHARACTERISTICS. Interface and physical dimensions. Conical seal, crush, 37 degree flared tube fitting, serrated supplied to this CID specification she

4、et shall be as specified herein (see figure 1 and table I). Beneficial comments, recommendations, additions, deletions, clarifications, etc., and any data that may improve this document should be sent to: DLA Land and Maritime, ATTN: VAI, P.O. Box 3990, Columbus OH 432183990, or fluidflowdla.mil. Si

5、nce contact information can change you may want to verify the currency of the address information using the ASSIST Online database at https:/assist.dla.mil/. AMSC N/A FSC 4730 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59935/6 2 Dash size co

6、de Tubing OD ref. A .010 B C T .002 -03 3/16 .325 .145.015 .130.005 .008 -04 1/4 .377 .183.015 .190.010 .008 -05 5/16 .440 .188.015 .255.005 .008 -06 3/8 .496 .205.015 .316.010 .007 -08 1/2 .676 .260.015 .426.010 .010 -10 5/8 .788 .268.015 .531.010 .010 -12 3/4 .963 .274.015 .671.010 .010 -14 7/8 1.

7、085 .280.015 .800.010 .010 -16 1 1.215 .285.015 .930.010 .012 -20 1-1/4 1.525 .335.015 1.160.010 .012 -24 1-1/2 1.785 .325.040 1.420.020 .012 -32 2 2.410 .430.040 1.915.010 .012 NOTES: 1. Dimensions are in inches. 2. Dimensioning and tolerancing in accordance with ASME Y14.5. 3. Break sharp edges an

8、d remove burrs and slivers. 4. Surface texture shall be .005 inches in accordance with ASME B46.1. 5. These parts are soft and easily deformed dimensions B, C, and D shall be verified by installing the seal on a standard fitting of the appropriate size. 6. An out-of-round-seal that does not interfer

9、e with installation shall not be cause for rejection. FIGURE 1. 37 flared Crush Seal. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59935/6 3 TABLE I. Material and finish code. Material and finish code Material and finish Loctite 1/ 2/ 3 Applic

10、ation C Copper foil or strip, annealed, type C10100, C10200 or C11000 in accordance with ASTM B152/B152M None CL Low temp Refrigeration CT Copper foil or strip, annealed, type C10100, C10200 or C11000 in accordance with ASTM B152/B152M Tin plated in accordance with ASTM B545 or SAE-AMS2408 None CTL

11、Low temp S Corrosion resistant steel strip type 304 or 305, annealed, in accordance with ASTM A240/A240M None Carbon steel fittings SL Low temp Carbon steel fittings ST Corrosion resistant steel strip type 316, annealed, In accordance with ASTM A240/A240M None Nuclear power STL Low temp Marine and c

12、orrosive environment STH High temp Oil and Steam 1/ Low temp -40F to 300F. 2/ High temperature -40F to 1200F. 3/ Loctite coating not for use in pure oxygen, oxygen rich systems, chlorine or other strong oxidizing materials. Torque technique. These seals require a second torque technique; see A-A-599

13、35 for torqueing procedure. NOTES PIN. The PIN should be used for Government purposes to buy commercial products to this CID specification sheet. See the classification section for PIN format example. Source of documents. COMMERCIAL ITEM DESCRIPTIONS A-A-59935 - Conical Seal, Crush, 37 Degree Flared

14、 Tube Fitting, General Requirements For (Copies of these documents are available online at http:/quicksearch.dla.mil/ or from the DLA Document Services Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 191115094). Provided by IHSNot for ResaleNo reproduction or networking permitted witho

15、ut license from IHS-,-,-A-A-59935/6 4 Other Publications ASME INTERNATIONAL ASME Y14.5 - Dimensioning and Tolerancing ASME B46.1 - Surface Texture (Surface Roughness, Waviness, and Lay) (Copies of these documents are available online at http:/www.asme.org or from the ASME International, Three Park A

16、venue, New York, NY 10016-5990.) ASTM INTERNATIONAL ASTM B152/B152M - Standard Specification for Copper Sheet, Strip, Plate, and Rolled Bar ASTM A240/A240M - Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applicati

17、ons ASTM B545 - Standard Specification for Electrodeposited Coatings of Tin (Copies of these documents are available online at http:/www.astm.org or from the ASTM International, P.O. Box C700, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.) SAE INTERNATIONAL SAE-AMS2408 - Plating, Tin (Cop

18、ies of these documents are available on line at www.sae.org from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, and Tel: 877-606-7323 inside USA and Canada or 724-776-4970 outside USA, email at CustomerServicesae.org.) Commercial products. As part of the market analysis and re

19、search effort, this CID specification sheet was coordinated with the following manufacturers of commercial products. At the time of CID specification sheet preparation and coordination, these manufacturers were known to have commercial products that would meet the requirements of this CID specificat

20、ion sheet. (NOTE: This information should not be considered as a list of approved manufacturers or be used to restrict acquisition to only the manufacturers shown.) MFRs CAGE number MFRs name and address 4D2Q4 Flaretite, Inc. 4036 Shadow Oak Fenton, MI 48430-9122 Part number (P/N) supersession data

21、. These CID specification sheet PINs supersede the following MFRs P/Ns as shown. This information is being provided to assist in reducing proliferation in the Government inventory system (see table II). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,

22、-A-A-59935/6 5 TABLE II. P/N supersession data. Dash number (see table I) AA59935/6 MFRs CAGE MFRs P/N 1/ Dash number (see table I) AA59935/6 MFRs P/N 1/ -02C 4D2Q4 37FT-02-CU-PLN -02CL 37FT-02-CU-SPP -03C 4D2Q4 37FT-03-CU-PLN -03CL 37FT-03-CU-SPP -04C 4D2Q4 37FT-04-CU-PLN -04CL 37FT-04-CU-SPP -05C

23、4D2Q4 37FT-05-CU-PLN -05CL 37FT-05-CU-SPP -06C 4D2Q4 37FT-06-CU-PLN -06CL 37FT-06-CU-SPP -08C 4D2Q4 37FT-08-CU-PLN -08CL 37FT-08-CU-SPP -10C 4D2Q4 37FT-10-CU-PLN -10CL 37FT-10-CU-SPP -12C 4D2Q4 37FT-12-CU-PLN -12CL 37FT-12-CU-SPP -14C 4D2Q4 37FT-14-CU-PLN -14CL 37FT-14-CU-SPP -16C 4D2Q4 37FT-16-CU-P

24、LN -16CL 37FT-16-CU-SPP -20C 4D2Q4 37FT-20-CU-PLN -20CL 37FT-20-CU-SPP -24C 4D2Q4 37FT-24-CU-PLN -24CL 37FT-24-CU-SPP -28C 4D2Q4 37FT-28-CU-PLN -28CL 37FT-28-CU-SPP -32C 4D2Q4 37FT-32-CU-PLN -32CL 37FT-32-CU-SPP Dash number (see table I) AA59935/6 MFRs CAGE MFRs P/N 1/ Dash number (see table I) AA59

25、935/6 MFRs P/N 1/ -02S 4D2Q4 37FT-02-304-PLN -02SL 37FT-02-304-SOR -03S 4D2Q4 37FT-03-304-PLN -03SL 37FT-03-304-SOR -04S 4D2Q4 37FT-04-304-PLN -04SL 37FT-04-304-SOR -05S 4D2Q4 37FT-05-304-PLN -05SL 37FT-05-304-SOR -06S 4D2Q4 37FT-06-304-PLN -06SL 37FT-06-304-SOR -08S 4D2Q4 37FT-08-304-PLN -08SL 37FT

26、-08-304-SOR -10S 4D2Q4 37FT-10-304-PLN -10SL 37FT-10-304-SOR -12S 4D2Q4 37FT-12-304-PLN -12SL 37FT-12-304-SOR -14S 4D2Q4 37FT-14-304-PLN -14SL 37FT-14-304-SOR -16S 4D2Q4 37FT-16-304-PLN -16SL 37FT-16-304-SOR -20S 4D2Q4 37FT-20-304-PLN -20SL 37FT-20-304-SOR -24S 4D2Q4 37FT-24-304-PLN -24SL 37FT-24-30

27、4-SOR -28S 4D2Q4 37FT-28-304-PLN -28SL 37FT-28-304-SOR -32S 4D2Q4 37FT-32-304-PLN -32SL 37FT-32-304-SOR See note at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59935/6 6 TABLE II. P/N supersession data - Continued. Dash number (

28、see table I) AA59935/6 MFRs CAGE MFRs P/N 1/ Dash number (see table I) AA59935/6 MFRs P/N 1/ -02ST 4D2Q4 37FT-02-316-PLN -02STL 37FT-02-316-SGR -03ST 4D2Q4 37FT-03-316-PLN -03STL 37FT-03-316-SGR -04ST 4D2Q4 37FT-04-316-PLN -04STL 37FT-04-316-SGR -05ST 4D2Q4 37FT-05-316-PLN -05STL 37FT-05-316-SGR -06

29、ST 4D2Q4 37FT-06-316-PLN -06STL 37FT-06-316-SGR -08ST 4D2Q4 37FT-08-316-PLN -08STL 37FT-08-316-SGR -10ST 4D2Q4 37FT-10-316-PLN -10STL 37FT-10-316-SGR -12ST 4D2Q4 37FT-12-316-PLN -12STL 37FT-12-316-SGR -12ST 4D2Q4 37FT-14-316-PLN -14STL 37FT-14-316-SGR -16ST 4D2Q4 37FT-16-316-PLN -16STL 37FT-16-316-S

30、GR -20ST 4D2Q4 37FT-20-316-PLN -20STL 37FT-20-316-SGR -24ST 4D2Q4 37FT-24-316-PLN -24STL 37FT-24-316-SGR -28ST 4D2Q4 37FT-28-316-PLN -28STL 37FT-28-316-SGR -32ST 4D2Q4 37FT-32-316-PLN -32STL 37FT-32-316-SGR Dash number (see table I) AA59935/6 MFRs CAGE MFRs P/N 1/ -02TH 4D2Q4 37FT-02-316-HTS -03TH 4

31、D2Q4 37FT-03-316-HTS -04TH 4D2Q4 37FT-04-316-HTS -05TH 4D2Q4 37FT-05-316-HTS -06TH 4D2Q4 37FT-06-316-HTS -08TH 4D2Q4 37FT-08-316-HTS -10TH 4D2Q4 37FT-10-316-HTS -12TH 4D2Q4 37FT-12-316-HTS -14TH 4D2Q4 37FT-14-316-HTS -16TH 4D2Q4 37FT-16-316-HTS -20TH 4D2Q4 37FT-20-316-HTS -24TH 4D2Q4 37FT-24-316-HTS

32、 -28TH 4D2Q4 37FT-28-316-HTS -32TH 4D2Q4 37FT-32-316-HTS 1/ The manufacturers P/N shall not be used for procurement to the requirements of this specification sheet. At the time of preparation of this specification sheet, the aforementioned commercial products were reviewed and could be replaced by t

33、he CID PIN shown. For actual part marking requirements, see the marking paragraph of A-A-59935. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59935/6 7 MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: Custodians: GSA - FAS Army - AV Navy

34、 - AS Air Force - 99 Preparing activity: DLA - CC DLA - CC Review activities: Army - AT, MI Project 4730-2013-081 Navy - MC, SH Air Force - 71 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-