1、I I 63T FED, CLASS. r. I rd MATERIAL IDENTIFICATION PER - I Ams2800. RAISED OR DEPRESSED OW .O10 MAX .188-“-/-c K TO FULL THD “I .O47 CHAMFER x 45 I I SECTION TKI L 1 +.!O0 1 PART NO. - .O60 .625 I (a) 1 AN101206 101207 AN101208 AN101210 AN101211 1 .O62 1.125 1 13; I AN101214 1.188 .500 AN101215 101
2、213 1.250 562 AN101216 1.312 I :625 I AN101217 THREAD L 1.375 1.438 1.500 1.562 1.625 1.688 1.750 1 .e75 2.000 2.125 2.250 2,500 2 * 375 2.625 -. 120t.030 - APPROX IMPERFECT THD I_ I - - .312 k- L .30gDIA t. a3125-24UNF-3A SPEC MIL-S-7742 ROFILE K + . O00 - -060 .688 .750 .e12 .a75 .938 1 .o00 1.062
3、 1.188 1.312 1.562 1.438 1.688 1.812 1.938 Y THIS SURFACE MUST BE SQUARE WITH SHANK WITHIN .O03 FIR. CHAMFER 30 TO ,500 DIA (OPPOSITE SIDE OPTIONAL) PART NO, L +.O00 K , - ,060 AN101218 2.750 2.062 AN101219 2.875 2.188 101220 3.000 2.312 AN101221 3.125 2.438 AN101222 3.250 2.562 AN101223 3.375 2.688
4、 AN101224 3.500 2.812 AN101225 3.625 2.938 AN101226 3.750 3.062 AN101227 3.875 3.188 AN101228 4.000 3.312 AN101229 4.125 3.438 AN101230 4.250 3.562 AN101231 4.375 3.688 - AN101238 5.250 AN101240 5.500 AN101241 5.625 AN101242 5 .T50 AN101243 5.875 AN101239 5 9 375 AN101244 II 6.000 AN101245 +.o00 K -
5、 -060 3.812 4 .o62 4,188 4.312 3.938 4.438 4 362 4.812 4.688 4.938 5.062 5.188 5.312 PART NO. AN101246 AN101247 AN101248 AN101249 101250 m101251 101252 AN101253 AN101254 AN101255 AN101257 m101256 AN101258 (a) THREAD TO HEAD. MAXIMUM TWO IMPERFECT THREADS, SHANK SHALL BE STRAIGHT WITHIN O03 FTR.PER I
6、NCH OF BOLT LENGTH. THE CONCENTRICITY OF THREAD PD IN RELATION TO THE SHANK SHALL BE WITHIN ,006 FIR- THE CONCENTRICITY OF THE SHANK IN RELATION TO THE WASHER FACE DIAMETER AND HEXAGON SHALL BE WITHIN 015 FIR. MATERIAL: STEEL AMs6322 HARDNESS: ROCKWELL 26-32 FINISH: CADMIUM PLATE AMs2400 SURFACE ROU
7、GHNESS: ns107 r 3 INSPECTION: ALL PARTS SHALL UNDERGO MAGNETIC INSPECTION-IN ACCORDANCE WITH AMS2640. ACTURING SPECIFICATION: AMs7452 REM SHARP EDGE3 .003-.015 UNLESS OTHERWISE SPECIFIED. DIMENSIONS IN INCHES. UNLESS OTHERWISE SBECIFIED:. TOLERANCES; LINEAR DIMENSIONS f.010, ANGULAR DIMENSIONS 22. D
8、O NOT USE UNASSIGNED PART NUMBERS. THIS STANDARD WAS DEVELOPED COOPERATPLY BY THE ENGINE AND PROPELLER UTILITY PARTS COMMITTEE OF THE SAE. AIR FORCE-NAVY AERONAUTICAL STANDARD AN I 0 I 20 I THAU P.A. AF-II CUST. NAVY- AS . BOLT - HEX HEAD .3125-24 ARMY-AV ANI 01.300 . THIS DOCUMENT CONTAINS J . PAGES. - “ “ 5306-0997 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1