DLA AN102401 THRU AN102500 REV 3-1986 BOLT - HEX HEAD DRILLED SHANK 500-20.pdf

1、AN102401 THRU AN102500 REV 3 53 E 7777715 0000235 O FED. SUP. CLASS. 5306 Cu AMS2800. RAISED OR DEPRESSED .O10 MAX K TO FULL THD -a .281 zz -MAX 2 f- E,ll 3 / LDRILL NO. 41 f.W4-.10lI lx CSINK BOTHSIDES 60. TO .150 DIA 2 HOLES ON AXIS OF SPEC MIL-S-7742 THIS SURFACE MUST BE SOUARE WITH SHANK THD WIT

2、HIN .005. ANGULAR LOCATION OF THIS GROUP AS A UNIT MAY VARY FREELY CHAMPER 30” TO .750 DIA (OPPOSITE SIDE OPTIONAL) WTHIN .o03 FIR. SECTION THRU THREAD PROFILE II A _ - 2.235 e: 2% 2.610 2.735 2.860 2.985 3.110 3 235 : : 2; 3.610 3.735 3.860 3.985 4.110 4.235 4 360 4.485 4.735 4.610 _ K +.o00 - .o60

3、 1.625 _ 1.500 1.750 L.875 2.000 2.125 2.250 2.375 2.500 2.625 2.750 2.875 3.000 3.125 3.250 3.375 3.500 3.625 3.750 3.875 4.000 11 A 4.860 4.985 5.110 5.235 5.360 5.485 5 I 610 5.735 5.860 _ - K + * O00 - .o60 4.125 4.250 4.500 4.625 4 -750 4.875 5,000 5.125 4.375 K - .o60 A +.O00 .798 (al .922 .i8

4、8 .%O .125 .985 .250 1.048 .312 1.110 .375 1.172 .438 1.235 .500 1.298 .562 ;:%: .688 1.485 .750 1.548 .812 1.610 .875 1.735 1.000 1.860 1.125 1.985 1.250 2.110 1.375 .625 PART NO.11 L PART NO. AN102445 AN102446 AN102447 AN102448 AN102450 AN102449 AN1024 5 1 AN102452 u1102453 L .938 1.000 1 .o62 1.1

5、25 1.188 1.250 1.312 33 1.500 1.562 1.625 1.688 37s; 2.000 2.125 2.250 2.375 2.500 =I- 2.625 ANlP2406 II ; AN102407 2 .875 AN102408 AN102427 5.375 AN102428 5.500 AN102429 5.625 AN102430 5.750 AN102431 5.875 AN102432 6.090 AN102409 3.125 AN102410 3.250 AN102411 3.375 AN102412 3.500 AN10241 3.625 AN10

6、2412 3.750 AN102415 3 .875 AN102416 /I 4.000 AN102417 4.125 AN102436 AN102437 AN102438 AN102439 AN102440 AN102441 11 4.250 AN102442 AN102443 (a) “IiREAD TO HEAD. MAXIMUM WO IMPERFECT THREADS. SHANK SHALL BE STRAIGHT WITHIN THE CONCENTRICITY OF THE SHANK IN RELATION TO THE WASHER FACE DIAMETER AND HE

7、XAGON .O02 FIR.PER INCH OF BOLT LENGTH. THE CONCENTRICITY OP THREAD PD IN RELATION TO THE SHANK SHALL BE WITHIN .o06 FIR. SHALL BE WITHIN .O23 FIR. MATERIAL: STEEL AMs6322 FINISH: CADMIUM PLATE AM92400 SURPACE ROUGHNESS: AS107 HAHITPACTIJRING SPECIFICATION: AMs7452 DIMENSIONS IN INCHES. DO NOT USE U

8、NASSIGNED PART NIIMBERS. HARDNESS: ROCKWELL C26-32 BREAK SHARP EDGES .003-.o15 UNLESS OTHERWISE SPECIFIED. UNLESS OTHERWISE SPECIFIED: TOLERANCES; LINEAR DIEIENSIONS f.010, ANGULAR DIMENSIONS f2 . WSPECTION: ALL PARTS SHALL UNDERGO MAGNETIC INSPECTION IN ACCQRDANCE WITH AMs2640 INACTIVE FOR NEW DESI

9、GN AFTER 3 MARCH 1969 NO SUPERSEDING STANDARD. THIS STANDARD WAS DEVELOPED COOPERATIVELY BY THE ENGINE AND PROPELLER UTILITY PARTS COMMITTEE OF THE SAE. AIR FORCE;-NAVY AERONAUTICAL STANDARD AN 102 401 ANI O 2500 P.A. Ar-Il THRU CUIT . NAVY - AS BOLT - HEX HEAD, DRILLED SHANK, .500-20 AR MY AV Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-