DLA AN102601 THRU AN102700 REV 3-1986 BOLT - HEX HEAD DRILLED SHANK 625-18.pdf

1、1 - AN302bOZ THRU ANZ02700 REV 3 53 7777735 0000237 V -y- 7- / - 2.465 2.590 2.715 WATERIAL IDENTIFICATION PER AMS2800. RAISED OR DEPRESSED .o10 MAX .344 1.625 1.750 1.875 E- l 102630 102631 102632 AN102633 AN102634 AN102635 CHAMPER 30 TO (OPPOSITE SIDE 6.000 5.840 5.000 SBCTION THRU THREAD PROFILE

2、3.590 3.715 3.840 3.965 ii.OgO 4.215 L 1.125 1.188 1.250 1.312 1.375 1.438 1.500 1.562 1.625 1.688 1.750 1.875 2.000 2.125 i ,812 2.250 2.375 2.500 2.750 2.875 3.000 3.125 3.250 3.375 A .965 1 .O28 1.090 1.152 1.215 1.340 1.402 1.465 1.528 1.590 1.652 1.715 1.840 1.965 2.090 2.215 2.340 1.278 AN1026

3、36 I AN102637 AN102638 AN1026iO AN102641 mi026 g K +.o00 - .o60 1 .125 .250 .312 .188 : 232 .500 .562 .625 .688 .750 .E12 .E75 1 .o00 1.125 1.250 1.375 1 .SOO . 4.590 4.840 4.715 4.965 K TO FULL THD .o16 OR CHAHFER 3.750 4.000 3.875 4.125 PART NO. II L I AIR FORCE-NAW AERONAUTICAL STANDARD P.A, A?-l

4、I I 2.625 2.750 2.875 AN 102 601 THRU 102609 3.375 102611 3.625 AN102610 /j 3.500 AN102612 3.750 AN102613 I 3.875 AN102614 4 .O00 CUIT , NAVY - AS ARMY -AV- AN102615 4.125 AN102616 / 4.250 AN102617 4.375 BOLT - HEX HEAD, DRILLED SHANK, -625-18 1 AN102700 AN102621 4.875 AN102622 5 .O00 mi02623 5,125

5、Il K - .o60 A I +.O00 PART NO. II L I A 1 +;!O0 -.o60 AN162624 5.250 5.090 4.250 AN102625 AN102626 / 5.5W 5.375 I 5.340 5.215 1 4.375 4.500 AN102627 II 5.625 1 5.465 I 4.625 AN102628 5.750 5.590 4.750 AN102629 5.875 5.715 4.875 AN102642 AN10264 AN102642 /I I 1 II I SHANK SHALL BE STRAIGHT WITHIN .O0

6、2 FIR. PER INCH OF BOLT LENGTH. THE CONCENTRICITY OF TiiREAD PD IN RELATION TO THE SHANK SHALL BE YI?1IIN .o06 FIR- THE CONCENTRICITY OF THE SHANK IN RELATION TO-THE WASHER FACE DIAMETER AND HEXAGON SHALL BE WITHIN .o28 FIR. MATERIAL: STEEL AMs6322 HARDNESS: ROCK!dELL C26-32 FINISH: CADMIUM PLATE AM

7、s2400 SURFACE ROUGHNESS: AS107 0 INSPECTION ALL PARTS SHALL UNDERGO MAGNETIC INSPECTION IN ACCORDANCE WITH AM52640 MANUFAClUFiING SPECIFICATION: AMS7452 BREAK SHARP EDGES .003-.015 UNLESS OTHERWISE SPECIFIED. DIMENSIONS IN INCHES. DO NOT USE UNASSIONED PART NUMBERS. U!LESS OTHERWISE SPECIFIED: TOLER

8、ANCES; LINEAR DIKENSIONS f.O1O, ANGULAR DIMENSIONS f2 . PART NO. mi02645 AN102646 AN102647 hi02648 AN102649 102650 102651 INACTIVE FOR NEW DESIGN AFTER 3 MARCH 1969 NO SUPERSEDING STANDARD. THIS DOCUMENT CONTAINS 1 PAGES? Project N. 5306-1011 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-