1、 ANLOi.Ii.IO1 THRU AN3Oi.ISOO REV 3 53 W 7777735 0000254 4 L 1.250 1.312 1.375 1.438 1.500 1.562 1.625 1.688 1.750 1 .a12 1 .a75 - THIS SURFACE MUST BE SQUARE WITH SHANK WITHIN -003 FIR. CHAMFER 30“ TO ,938 DIA (OPPOSITE SIDE OPTIONAL) SECTION THFiU THREAD PROFILE PART NO.- L 1.938 2.000 2.062 AN104
2、406 2.125 AN104407 2. i88 AN104408 2.250 AN104409 2.312 AN104410 2.375 AN104411 2.438 AN104412 2.500 AN104413 2.625 AN104414 2.750 AN104415 2 .875 AN104416 3 .O00 I PART NO. L .438 AN104417 3.125 .500 AN104418 3.250 .562 AN104419 3.375 AN104420 3,500 I AN104421 11 3.625 .750 AN104422 3.750 AN104423
3、3.875 :+; I AU104424 11 4.000 .938 AN104425 4.125 1.375 I AN104429 II 4.625 1.500 AN104430 4.750 I II (a) THREAD TO HEAD. MAXIHUM TWO IHPERFECT THREADS. .K t .o00 - .O60 1.625 1.750 1.875 2.000 2.125 2.250 2 :375 2.500 2.625 2.750 2.875 3.125 3; 250 3.000 K -.o60 PART NO. L +,O00 PART NO. AN304431 4
4、.875 3.375 AN104445 AN104432 I/ 5.000 I 3.500 I AN104446 AN104433 5.125 3.625 AN104447 AN104434 5.250 3.750 AN104448 AN104436 5.500 $:O00 AN104450 AN104437 5.625 4.125 .AN104451 AN104438 5.750 4.250 AN104452 AN104439 5 .875 4.375 AN104453 AN104440 6.000 4.500 AN104454 AN104441 AN104442 mio4435 5.375
5、 a75 104449 104443 104444 NOTE: (i) -SHANK SHALL BE STRAIGHT WITHIN ,002 FIR. PER INCH OF BOLT LENGTH. (2) THE CONCENTRICITY OP THREAD PD IN RELATION TO THE SHANK SHALL BE WITHIN .O06 FIR, (3) THE CONCENTRICITY OF THE SHANK IN RELATION TO TBE WASHER FACE DIAMETER AND HEXAGON SHALL BE WITHIN .O28 FIR
6、. XATERIAL: STEEL AMs6322 HARDNESS: ROCKWELL C26-32 FINISH: CADHIUY PLATE AHS2400 SUPPACK POUCUYBSS: AS107 HANUPACTURING SPECIFICATION: ANS7452 3INSPECTION : ALL PARTS SHALL UNDERGO- HAGNETIC INSPECTION IN ACCORDANCE WITH ANS2640 BREAK SHARP EDGES .003-.O15 UNLESS OTHERWISE SPECIFIED. DIXENSIONS IN
7、INCHES. UNLESS OTHERWISE SPECIFIED: TOLERANCES; LINEAR DIHENSIONS f.010. ANGULAR DIMENSIONS IZO. DO NOT USE UNASSIGNED PART NUMBERS, INACTIVE FOR NEW DESIGN AFTER 3 MARCH 1969 NO SUPERSEINO STANDARD. THIS STANDARD WAS DEVELOPED COOPERATIVELY BY THE ENGINE AND PROPELLER UTILITY PARTS COIHITTEE OF THE
8、 SAE. AN 104401 AN IO45 O AIR FORCE-NAVY AERONAUTICAL STANDARD P.A. Af-11 THRU CUIT NAVY-AS BOLT - DRILLED HEX HEAD, 6 HOLES, .625-18 ARMY-AV . f- . THIS DOCUblENT CONTAINS I- - PAGES. , Project Wo.5306-1028 *U.S. GOVERNMENT PRINTING OFFICE: 1988 - 606-036/46106- Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1