1、ANLO95Oi THRU AN309600 REV 3 53 7797735 0000255 6 U K TO FULL.T .235 TO POINT .O16 OR CHAMP DRILL .188 TO DEPTH SHOWN THIS SURFACE MUST.BE SQUARE WITH SHANK WITHIN .O03 FIR. - .O60 1 A75 1.938 I ;i 2,000 .250 2.062 .312 2.125 .375 I I SECTION THRU THREAD PROFILE CHAMPER 30 TO 1.062 DIA (OPPOSITE SID
2、E OPTIONAL) 2.250 2 I 312 AN104506 /I 2.375 AN104507 2.438 AN104508 2,500 AN104509 2.562 AN104510 11 2.625 AN104511 2.688 AN104512 II 2.750 AN104513 i 2.875 AN104515 I/ 3-.125 AN104516 3.250 A104514 i 3.000 K +.o00 - .O60 .438 .500 .562 -. _ ,625 .688 .750 .a12 a875 .938 1.000 1,125 1.250 1.375 1.50
3、0 AN104520 3.750 AN104521 3.875 AN104522 4 .O00 II AN104523 4.125 AN104524 4.250 AN104525 4.375 AN104526 4.500 AN104527 11.625 AN104528 4.750 K + . O00 - ,060 1.625 1.750 1.875 2.000 2.125 2.250 2.375 2.50.0 2.625 2.750 2.875 3_. O00 3.125 3.250 AN104531 5.125 AN104532 11 5.250 AN104533 5.375 AN1045
4、34 11 5.500 AN104535 5.625. 104536 5,750 AN104540 AN104541 AN10454 104542 K + . O00 - .o60 3.375 3.500 3.625 3.750 3.875 4.000 4.125 4.250 PART NO. AN104545 AN104546 AN104547 AN104548 AN104549 AN104550 AN104551 AN104552 (a) THREAD TO HEAD. MAXIMUM TWO IMPERFECT THREADS. NOTE: (1) SHANK SHALL BE STRA
5、IGHT WITHIN .O02 FIR. PER INCH OP BOLT LENGTH. (2) (31 THE CONCENTRICITY OF THREAD PD IN RELATION TO THE SHANK SHALL BE WITHIN THE CONCENTRICITY OF THE SHANK IN RELATION TO THE WASHER FACE DIAMETER AND HEXAGON .O06 FIR. . SHALL BEWITHIN .o32 FIR. MATERIAL: STEEL AMs6322 HARDNESS: ROCKWELL C26-32 FTN
6、ISH: CADMIUM PLATE AMs2400 SURPICI ROUCRAESS: AS107 MANUFACTURING SPECIFICATION: AM57452 3 INSPECTION: ALL PARTS SHALL UNDERGO MAGNETIC INSPECTION IN ACCORDANCE WITH AMs264 BREAK SHARP EDGES .003-.O15 UNLESS OTHERWISE SPECIFIED. DIMENSTONS I1 INCHES. UNLESS OTHERWISE SPECIFIED: TOLERANCES; LINEAR DI
7、MENSIONS f.010, ANGULAR DIMENSIONS t2. DO NOT USE UNASSIGNED PART NUMBERS. THIS DOCUMENT CONTAINS I- PAGES. INACTIVE FOR NEW DESIGN AFTER 3 MARCH 1969 No SUPERSEDING STANDARD. THIS STANDARD WAS DEVELOPED COOPERATIVELY BY THE ENGINE AND PROPELLER UTILITY PARTS COMMITTEE OF THE SAE I AIR FORCE-NAVY AERONAUTICAL STANDARD A Ni04 501 THRU P.A. Ar-Il I AN104600 CUST . NAVY-AS BOLT - DRILLED HEX HEAD, 6 HOLES, e750-16 ARMY-AV - .- Project No. 5306-1029 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1