DLA AN106101 THRU AN106200 REV 3-1986 BOLT-CRES HEX HEAD DRILLED SHANK 5625-18《螺栓 耐蚀钢六角头 钻孔螺杆 5625-18》.pdf

1、ANLObLOL THRU ANLO6200 REV 3 53 9979735 000027L 4 9 .i7*/9 FED. SUP CLASS. 5306 MATERIAL IDENTlTICATION PER I1Ks2800. RAISED OR DEPRESSED r- .o10 MAX .312 L - 1.062 t : 33 1.250 1.312 1.438 1.500 1 - 375 1.562 1.625 1.688 1.750 1.812 1.875 2.000 2.125 2.250 2 * 375 NOTE: .150 .o90 - A - .go2 a 965 1

2、.028 1.090 1.152 1.215 1.278 :E: 1.465 1.528 1.652 1 - 590 :E 1.965 2.090 2.215 SECT101 TIPIO THRW CSINK BOTH ENDS 60. TO -188 DIA - 2 HOLES ON AXIS 01 THIS smmx mr BB samm um SHAX VITHIII -003 RILt IRDICATl .125 . 106106 .i88 10610 ,375 i06ii0 .438 106111 ,500 106112 .562 10611 ,250 AN10610g .3l2 A

3、N106109 _ ,625 AN10611i .688 AN106115 ,750 106116 .12 A?+l06117 .75 AN106118 .938 AN106119 1.062 106120 i. i88 106121 1.438 106123 1.312 AN106122 RWIIO CAAWER 30. TO .e5 DU (OPPOSITP SIDE OPTIOKAL) L A 2.500 2. 40 2.625 2.t65 2.750 2.590 2.875 2. 15 3.000 2.840 3.125 2.965 3.250 3.090 3.375 3.215 3.

4、500 3.340 3.625 3.465 3- 50 3.590 3.: 2.562 2.688 2.812 3.062 3.188 3.312 3.438 3.562 3.688 2.938 3.812 t : 092; PART 10. AN106124 AN106125 A106126 10612 AN106126 AN106129 AiO613i AN106132 AN106133 AN106134 AN106135 AN1061s AN106137 AN106138 106130 %:“,tog AN106141 AN106142 AN106143 AN106144 - L - 5

5、.125 5.250 5.375 5.500 5 * 625 5.750 5.875 6.000 - THD WITHIN .005. ANOULAR MOATIOA OF THIS (ROUP AS 1 UNIT HAY VARY rnEELY 5. 15 4.938 5.Lo 5.062 (i) SHANK SHALL BE STRAIGHT WITHIN .O02 FIR. PER INCH OF BOLT LENGTH. (2) THE CONCENTRICITY OF THREAD PO IN RELATION TO THE SHANK SHALL BE WITHIN .O06 FI

6、R. (3) THE CONCENTRICITY OF THE SHANK IN RELATION TO THE WASHER FACE DIAHETER AND HEXAGON SHALL BE WITHIN .O26 FIR. PART 10. AN10145 AN106146 AN106147 AN106148 AN106149 AH106151 AH106152 106150 INACTIVE FOR DESIGN AFTER 27 DEC 1966 NO SUPERSEDING STANDARD. HATERIAL: CORROSION RESTSTANT STEEL - SEE M

7、ANUFACTURING SPECIFICATION SURFACE ROUGHNESS: AS407 HANPFACTURING SPECIFICATION: AHS 1472 BREAK SHARP EDGES .003-.O15 UNLESS OTHERWISE SPECIFIED. DIHENSIONS IN XNCHES. UNLESS OTHERWISE SPECIFIED: TOLERANCES; LINEAR DIHENSIONS t.010, ANGULAR DO NOT USE UNASSIGNED PART NUHBERS. THIS STANDARD WAS DEVEL

8、OPED COOPERATIVELY WITH THE ENGINE AND PROPELLER UTILETY PARTS COHHITTEE OF THE SAE. P.A. Other CUSL 3 INSPECTION: ALL PARTS SHALL UNDERCO FLUORESCENT PENETRANT INSPECTON IN ACCORDANCE WITH AHS2645. DIYENSIONS 2 AIR FORCE-NAVY AERONAUTICAL STANDARD AN I 06 10 I USAF - II Navy - AS Army - AV ANI $!2200 BOLT - CRES HEX HEAD, DRILLED SHANK, .3625-18 I I Project No. 5306-104 I UnMIIT sm O.NL ,-li, IIVIII7 THIS DOCUMENT CONTAINS I PAGES. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-