DLA AN107601 THRU AN107700 REV 3-1986 BOLT-CRES DRILLED HEX HEAD 6 HOLES 375-24《螺栓 耐蚀钢钻孔六角头 6孔 375-24》.pdf

1、- _-_ -e- AN10760I THRU ANI07700 REV 3 53 rn 9999915 0000286 b rn - L - .625 .688 .750 .a12 .a75 .938 .o00 .O62 . I25 .I88 .250 .312 .375 - THIS SURFACE HUST BE SQUARE WITH SHANK WITHIN .O03 FULL INDICATOR 4RILL N0.50 (.070) READING CSINK 90 TO .LOO DIA CHAMFER 30 TO .562 DIA (OPPOSITE SIDE OPTIONAL

2、) 6 HOLES SPACE AS SHOWN WITHIN .O20 OF TRUE POSITION PART NO. -. O60 AN107608 1.625 I .625 AN107609 1.688 .688 AN107610 1.750 .750 11 AN107611 1.812 .12 AN107612 1.875 .E75 AN107613 1.938 .938 AN107614 2.000 1.000 AN107615 2.125 1.125 AN107616 2.250 1.250 AN107617 I/ 2.375 1 1.375 AN107618 2.500 1.

3、500 -IrI_ AN107619 2.625 2.750 2.875 11 AN407622 3.000 AN107627 3.125 AN107624 3.250 AN107625 3.375 AN107626 3.500 AN107627 3.625 AN107628 2.750 AN107629 3.750 AN107630 4.000 11 AN107631 4.125 AN107632 (1 4.250 K +.o01 - .O61 1.625 1.750 1.875 2.000 2.125 2.250 2.375 2;500 2.625 2.750 2.875 3.000 3.

4、125 3.250 PART NO. 5.500 AN107643 5.625 A:Z I/ 5.750 AN107645 )I 5.875 AN107646 6.000 +.O00 PART N I -. 060 3.375 AN1076 3.500 AN1076 3.6-25 AN1076 3,750 AN1076 3.875. AN1076 4.000 I AN1076 4.125 AN1076 4.250 AN1076 4.375 AH1076 4.500 AN1076 4.625 AN1076 4.750 I AN1076 4.675 AN1076: 5.000 AN10761 (a

5、) THREAD TO HEAD. NAXIHUM TWO IHPERFECT THREADS. NOTE: (i) SHANK SHALL BE STRAIGHT WITHIN .O025 FIR. PER INCH OF BOLT LENGTH. (2) THE CONCENTRICITY OF THREAD ED IN RELATION TO THE SHANK SHALL BE WITHIN .O06 FIR. (3) THE CONCENTRICITY OF THE SHANK IN RELATION TO THE WASHER FACE DIAHETER AND HEXAGON S

6、HALL BE WITHIN .O17 FIR. INACTIVE FOR DESIGN AFTER 27DEC 1966 NO SUPERSEDING STANDARD. HATERIAL: CORROSION RESLSTANT STEEL - SEE MANUFACTURING SPECIFICATION SURFACE ROUGHNESS: AS107 HANUFACTURING SPECIFICATION: AMS 7472 INSPECTION: ALL PARTS UNDERGO FLUORESCENT PENETRANT INSPECTION IN ACCORDANCE- WI

7、TH AHS2645. BREAK SHARP EDGES .O03 - .O15 UNLESS OTHERWISE SPECIFIED. DIHENSIONS IN INCHES: INLESS OTHERWISE SPECIFIED: TOLERANCES; LINEAR DIMENSIONS 1.010. ANGULAR DIHENSIONS 12 . DO NOT USE UNASSIGNED PART NUMBERS. THIS STANDARD WAS DEVELOPED COOPERATIVELY WITH THE ENGINE AND PROPELLER UTILITY PAR

8、TS COHMITTEE OF THE SA AN I 0760 I AN I8“i300 / Prn*ct No. 5306-1060 .A. AIR FORCE-NAVY AERONAUTICAL STANDARD Ither Cust USAF - 11 Navy - AS BOLT - CRES DRILLED HEX HEAD. 6 HOLES, .375 - 24 Army - AV UJvmlUm Pm 0rmL- iar-r,i-5iYrpx THIS DOCUMENT CONTAINS . I - PAGES. , Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-