1、r r ANLOBLOL THRU ANLOB200 REV 3 53 m 77777L5 000027L T m HkTERIAL IDENTIFICATLON RAISED OR L 63 K TO FULL TH .235 TO POINT .O62 X 45 .O16 OR CHAHFER IHPERFECT SECTION THRU TAREA PROFILE THIS- SURFACE HUST BE SQUARE WITH O. 50 1.070) .LOO DIA 6 HOLES SPACE0 AS SHOWN WITHIN .O20 OF TRUE POSITION CSIN
2、K 90. TO CHAHFER 30 TO 1.062 DIA (OPPOSITE SIDE OPTIONAL) L 500 562 625 688 750 812 875 938 O00 062 125 K +. O00 -.O60 PART NO. AN I08 106 AN 1 O8 107 AN108 I08 AN108 109 AN1 O8 11 O AN I08 1 I1 AN108 I 12 ANI08 11 3 ANI O8 114 ANI08 11 5 AN1081 I6 - L 2,188 2.250 2.312 2.375 2.438 2.500 2,562 2.625
3、 2.688 2.750 2.875 3.000 3.125 3.250 - K +. O00 - . O60 .438 .500 -362 .625 .688 .750 .e12 .875 .938 1 .o00 1.125 1.250 1.375 1.500 FART NO. AN!O8 i 17 AN108 1 I8 AN 108 I1 9 ANI08120 AN108 12 I ANI08122 ANI O81 2 3 AN108 124 AN I O8 125 ANI O8 I26 AN108 12 7 AN1081 28 AN I O8 129 AN108130 L 3.375 3
4、.500 3.625 3.750 3.875 4.000 4.125 4.250 4.375 4.500 4.625 4.750 4.875 5.000 - K 1 PART NO. +*Ooo -.O60 I 1.625 ANI08131 1.750 AN108132 1.875 AN108133 2.000 AN108134 2.125 AN108135 2.250 AN108136 2.375 AN108137 2.500 AN108138 2.625 AN108139 2.750 AN108140- 2.875 AN108141 3.000 AN108142 3.125 AN10814
5、3 3.250 AN108144 I I- l I +.o00 5.125 3.315 AN10814 5.250 3.500 AN10814 5.375 3.625 AN10814 5.500 3.750 AN10814 5.625 3.875 AN10814 5.750 4.000 AN10815 (a) THREAD. TO HEAD. HAXIHUH TWO IHPERFECT TNREAnS. NOTE: (IX SHANK SHALL BE STRAIGHT WITHIN .O02 FIR. PER INCH OF BOLT LENGTH. (2)- THE CONCENTRICI
6、TY OF THREAD PD IN RELATION TO THE SHANK SHALL BE WITHIN .O06 FIR. (3). THE CONCENTRICITY OF THE SHANK IN RELATION TO THE WASHER FACE OIAHETER AND HEXAGON SHALL BE WITHIN .O32 FIR. INACTIVE FOR DESIGN AFTER. 27 DEC 1966 NO SUPERSEDING STANDARD. KA TE PI AL. CORROSION RESISTANT STEEL - SEE UANUFACTUR
7、ING SPECIFICATION SUPFACE ROUGHNESS: AS107 IANUFACTURING SPECIFICATION: AUS 7472 IINSPECTON: ALL PARTS SHALL UNDERGO FLUORESCENT PENETRANT INSPECTION IN ACCORDANCR WITH AHC2645. BREAK SHAP EDGES .O03 - .O15 UNLESS OTHERWISE SPECIFIED. DIYENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED: TOLERANCES: LIN
8、EAR DIHENSIONS i.010. ANGULAR DIHENSIONS 22 DO NOT USEiUNASSIGNED PART NUHBERS. THIS STANDXRD WAS DEVELOPED COOPERATIVELY WITH THE ENGINE AND PROPELLER UTILITY PARTS COHHITTEE OF THE SAE, P.A. USAF - 11 Navy - AS Army - AV. Ocher Cust AIR FORCE-NAVY AERONAUTICAL STANDARD AN 08 I 0 I THRU AN108200 BOLT - CRES DRILLED HEX HEAD, 6 HOLES, .750-16 F THIS DOCUMENT CONTAINS -I- . PAGES. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1