1、- . ANL27787 THRU ANL2BOBb REV 3 53 = 7777735 0000345 7 INACTiVE SECTION THRU THREAD PROFILE BOTH THD SIZES FOR DESIGN AFTER 26 OCTOBER 1972. NO SUPERSEDING STANDARC CHAYPER .078x45 APPROX NOTE: PITCH DIAMETERS OF BOTH THREADED ENDS SHALL BE CONCENTRIC WITHIN ,006 FIR. HATERIAL: STEEL AMs 6322. (AMs
2、 6320 MATERAL MAY ALSO BE USED FOR THESE PARTS UNTIL 1 JAN 1960.) HARDNESS: ROCKWELL C26-32. FINISH: CADMIUM PLATE AMs 2400. DIMENSIONS ARE AFTER PLATING EXCEPT WHERE SHOWN. SURFACE ROUGHNESS: AS 291 MANUFACTURING SPECIFICATION AMS 7456. BREAK SHARP EDGES .003-.D15 UNLESS OTHERWISE SPECIFIED. DIMENS
3、IONS IN INCHES. UNLESS OTHERWISE SPECF1ED:TOLERANCES; LINEAR DIMENSIONS i.010. DO NOT USE INASSIGNED PART NUMBERS. THIS STANDARD WAS DEVELOPED COOPERATIVELY WITH THE ENGINE AND PROPELLER UTILITY PARTS COMMITTEE OF THE SAE. INSPECTION: ALL PARTS SHALL UNDERGO MAGNETIC INSPECTION IN ACCORDANCE WITH AM
4、S2640. / UNDERSIZE AND OVERSIZE- IDENTIPICATI0N STAMP PER AMs2800 .O10 MAX DEPTH PA 11 I AIR FORCE-NAW AERONAUTICAL STANDARD . CUST: AV, AS STUD - STRAIGHT, NECKED, .5625-12 x .5625-18 i 11 UNDERSIZE AND AN I27787 THRU AN 128086 OVERSIZE IDENTIFICATION D BEFORE PLATING D AFTER PLATING D LEAD THREAD
5、LI AI B YL-I 1 .5625-12NS SEE TABLE FOR PD - .O03 .557 -.562 .!i104 -.5114 .5iOg- .5124 .5034-.5054 PART NUMBER AN127799 AN127805 AN127811 AN127817 AN127823 AN127829 AN 12 78 35 AN127841 AN127847 AN127853 AN127859 AN127865 +E%+ AN127883 AN127889 AN127895 AN127901 AN127907 AN127913 AN127919 AN127925
6、AN127931 AN127937 AN127943 AN127949 AN127955 AN127971 AN127979 AN127985 AN127991 AN127997 AN128003 AN128009 mi28015 AN128021 %i%-.%- STANDARD .5139-.5154 127800 AN127830 AN127836 AN127866 AN127890 127920 AN127926 AM27944 AN127950 AN127962 mi127956 AN127980 AN127986 AN128010 AN128016 +. 003 -557 -a56
7、2 .5164-.5174 5169-.5184 .5094-.5114 PART NUMBER AN127801 AN127807 %+E+ AN127825 AN127831 AN127837 AN127843 AN127849 AN127855 AN127867 127861 AN127885 AN127891 AN127897 AN127903 AN127909 AN127915 U127921 AN12792 7 AN127933 AN127939 AN127945 AN127951 AN127957 AN127963 AN127969 AN127975 AN127981 AN127987 AN127993 AN127999 128005 Ah128011 AN128017 AN128023 .5625-iUNP-3A1 MIL-S-7742 I FED. .SWCLASS CHAMFER .06245O APPROX STAMP PER AHS2OO .O10 MAX DEPTH +. 006 I +.o09 t. 012 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1