DLA AN800 REV 6-2011 CONE-UNION.pdf

1、AMSC N/A FSC 4730 AN800 Rev 6 4 August 2011 SUPERSEDING AN800 Rev 5 1 June 1954 DETAIL SPECIFICATION SHEET CONE, UNION This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of thi

2、s specification sheet and MIL-DTL-6001. FIGURE 1. Cone, union. INCH-POUND Inactive for new design after 24 July 1998. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TABLE I. Dash numbers and size. 1/ 2/ Brass Corrosion resistant steel Nickel copper

3、alloy Tube outside diameter A Diameter B C Diameter D +.000 -.004 Diameter F +.000 -.004 Diameter G H K Diameter M Spher radious 2 C2 N2 .125 .1285 .156 .076 .165 .265 .375 .125 .125 .141 3 .188 .191 .140 .250 .320 .438 .172 .172 4 .250 .257 .188 .157 .312 .375 .500 .203 .203 5 .312 .323 .219 .219 .

4、375 .437 .594 .156 .266 .266 6 .375 .386 .281 .469 .547 .719 .328 .328 8 .500 .516 .250 .406 .594 .672 .906 .188 .453 .422 10 .625 .641 .281 .531 .715 .844 1.031 .219 .594 .562 TABLE I. Dash numbers and size Continued. 1/ 2/ Brass Corrosion resistant steel Nickel copper alloy Tube outside diameter A

5、 Diameter B C Diameter D +.000 -.102 Diameter F +.000 -.102 Diameter G H K Diameter M Spher radious 2 C2 N2 3.175 3.264 3.962 1.930 4.191 6.731 9.525 3.175 3.175 3.581 3 4.775 4.851 3.556 6.350 8.128 11.125 4.369 4.369 4 6.350 6.528 4.775 3.988 7.925 9.525 12.70 5.156 5.156 5 7.925 8.204 5.563 5.563

6、 9.525 11.100 15.088 3.962 6.756 6.756 6 9.525 9.804 7.137 11.913 13.894 18.263 8.331 8.331 8 12.700 13.106 6.350 10.312 15.088 17.069 23.012 4.775 11.506 10.719 10 15.875 16.281 7.137 13.487 18.161 21.438 26.187 5.563 15.088 14.275 1/ Dimensions are in inches 2/ Metric equivalents are given for inf

7、ormation only. AN800 Rev62Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AN800 Rev 6 3 REQUIREMENTS Dimensions. See table I. Unless otherwise specified tolerances on decimals are .010, angles 0.5. Configuration. See figure 1. Surfaces “S” must run t

8、rue with each other within .002 full indicator measurement. Inactive for new design. Dash numbers 12 and 16 are inactive for new design. Dash numbers 2, 3 and 4 are inactive for new design except for use in oxygen systems and engine primer lines. Dash numbers 5, 6, 8 and 10 are inactive for new desi

9、gn and are not to be used on engine primer lines. Materials: Brass; bars, shapes or forgings. Corrosion resistant steel; bars, shapes or forgings. Nickel copper alloy; bars, shapes or forgings. See procurement specification. Finish: See procurement specification. Identification of product. Add P bef

10、ore the dash number for cadmium plated brass cones and for cadmium plated nickel copper alloy cones. AN800 X X Size Material, finish Drawing number Example of Part or Identifying Number (PIN): AN800-2 cone union, brass, for .125 tubing OD. AN800P2 cone union, brass, cadmium plated, for .125 tubing O

11、D. AN800C2 cone union, corrosion resistant steel, for .125 tubing OD. AN800N2 cone union, nickel copper alloy, for .125 tubing OD. AN800PC2 cone union, nickel copper alloy, cadmium plated, for .125 tubing OD. Workmanship. Break all sharp edges and remove all hanging burrs and slivers which might bec

12、ome dislodged under usage. Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Referenced documents. This document references MIL-DTL-6001. CONCLUDING MATERIAL Custodians: Preparing act

13、ivity: Army AR DLA - CC Navy SH Air Force - 99 DLA - CC (Project 4730-2010-184) Review activities: Army AT, AV, CR4 Navy AS, CG, MC, SA, YD Air Force - 71 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-