DLA CCC-W-408 D-1994 WALL COVERING VINYL-COATED《乙烯基涂层墙面涂料》.pdf

1、CCC-W-408D m 9999974 0362270 L24 I INCH-POUND I CCC-W-408D January 14. 1994 SUPERSEDING July 11, 1989 CCC-W-408C FEDERAL SPECIFICATION WALL COVERING, VINYL-COATED This specification is approved by the Commissioner, Federal Supply Service, General Services Administration, for the use of all Federal a

2、gencies. 1. SCOPE AND CLASSIFICATION 1.1 Scope. This specification covers vinyl-coated wall coverings. 1.2 Classification. The vinyl-coated wall coverings are of the following types, as specified (see 6.2). Type I - Light duty. Type II - Medium duty. Type III - Heavy duty. 2. APPLICABLE DOCUMENTS 2.

3、1 Government documents. 2.1.1 Specifications, standards. and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Def

4、ense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). IBeneficial comments (recommendations, additions, deletions) and any pertinent1 Idata which may be of use in improving this document should be addressed to: I ICommanding Officer (Code 15

5、6), Naval Construction Battalion Center, 11000 23rd Avenue, Port Hueneme, CA 93043-4301, by using the Standardization I IDocument Improvement Proposal (DD Form 1426) appearing at the end of this I ldocument or bv letter. I I FSC 5640 O DISTRIBUTION STATEMENT A. Approved for public release; distribut

6、ion is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-CCC-W-4OBD W 9999974 OLb229L Ob0 m CCC-W-408D Federal SDecification PPP-P-1136 - Packaging of Coated (Plastic; Rubber) and Laminated Fabrics Federal Standard FED-STD-191 - Textile Test

7、 Methods (Activities outside the Federal Government may obtain copies of Federal specifications, standards, and commercial item descriptions as outlined under General Information in the Index of Federal Specifications, Standards, and Commercial Item Descriptions. The Index, which includes cumulative

8、 bimonthly supplements as issued, is for sale on a subscription basis by the Superintendent of Documents, U.S. Government Printing Office, Washington, DC 20402.) (Single copies of this specification and other Federal specifications and commercial item descriptions required by activities outside the

9、Federal Government for bidding purposes are available without charge from General Services Administration Business Service Centers in Boston, MA; New York, NY; Philadelphia, PA; Washington, DC; Atlanta, GA; Chicago, IL; Kansas City, MO; Fort Worth, TX; Houston, TX; Denver, CO; San Francisco, CA; Los

10、 Angeles, CA; and Seattle, WA.) (Federal Government activities may obtain copies of Federal standardization documents, and the Index of Federal Specifications, Standards, and Commercial Item Descriptions from established distribution points in their agencies.) Military Standards MIL-STD-105 - Sampli

11、ng Procedures and Tables for Inspection by MIL-STD-1623 - Fire Performance Requirements and Approved Specifications Attributes for Interior Finish Materials and Furnishings (Naval Shipboard Use) (Copies of military specifications and standards required by contractors in connection with specific acqu

12、isition functions should be obtained from the procuring activity or as directed by the contracting officer.) 2.2 Other wblications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues are those cited in the solicitation (see 6.2

13、). ASTM ASTM D 685 - Conditioning Paper and Paper Products for Testing ASTM D 751 - Coated Fabrics ASTM D 2486 - Scrub Resistance of Interior Latex Flat Wall Paints ASTM E 84 - Surface Burning Characteristics of Building Materials ASTM G 21 - Determining Resistance of Synthetic Polymeric Materials t

14、o Fungi (Application for copies should be addressed to ASTM, 1916 Race Street, Philadelphia, PA 19103-1187.) 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-CCC-W-408D m 9999974 0362292 TT7 m CCC-W-408D O (Non-Government standards and other publica

15、tions are normally available from the organizations that prepare or distribute the documents. These documents also may be available in or through libraries or other informational services.) 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited

16、 herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 First article. When specified in the contract or purchase order (see 6.2), the contractor shall furnis

17、h a complete roll of vinyl-coated wall covering of the type, surface texture, pattern, color, grain, and size specified for first article inspection and approval (see 4.2.1 and 6.3). 3.2 Standard commercial Product. The vinyl-coated wall covering of the same classification shall, as a minimum, be in

18、 accordance with the requirements of this specification and shall be the manufacturers standard commercial product. Additional or better features which are not specifically prohibited by this specification but which are a part of the manufacturers standard commercial product, shall be included in th

19、e vinyl-coated wall covering being furnished. A standard commercial product is a product which has been sold or is being currently offered for sale on the commercial market through advertisements or manufacturers catalogs or brochures, and represents the latest production model. 3.3 Materials. Mater

20、ials used shall be free from defects which would adversely affect the performance or maintainability of individual components or of the overall assembly. Materials not specified herein shall be of the same quality used for the intended purpose in commercial practice. Unless otherwise specified herei

21、n, all equipment, material, and articles incorporated in the work covered by this specification are to be new and fabricated using materials produced from recovered materials to the maximum extent possible without jeopardizing the intended use. The term “recovered materials” means materials which ha

22、ve been collected or recovered from solid waste and reprocessed to become a source of raw materials, as opposed to virgin raw materials. Unless otherwise specified, none of the above shall be interpreted to mean that the use of used or rebuilt products is allowed under this specification. 3.3.1 Supp

23、orting - material. The supporting substrate of the material shall be of woven cloth, nonwoven fabric, or other suitable materials, the use of which enables the vinyl-coated wall covering to meet the requirements of this specification. 3.4 Physical properties. The physical properties for vinyl-coated

24、 wall covering covered by this specification shall meet the requirements of table I when tested in accordance with the tests of 4.4 through 4.4.7. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-CCC-W-408D m 9999974 0362293 933 m CCC-W-408D TABLE I

25、. Physical properties. I I I I I I Requirements I Type I 1 Type II I Type III I I I l I I l I I I I I Color fastness to light L/ I Washability (cycles, min)2/ I Scrubability (cycles, min) L/ I Abrasion resistance I (cycles, min) 2/ J/ I Breaking strength (pounds/kilo, min) 1 (machine direction) I (c

26、ross machine direction) I Crocking h/ I Stain resistance (reagents) I Tear resistance (both directions) I (scale rating, min) 1 Blocking resistance I (scale rating, max) I Coating adhesion I (pounds/inch, min) L/ I Cold crack resistance 20F (-6.7OC) I Heat aging resistance 1 (7 days at 158F ( 7OoC)

27、I Flame spread (max) I Smoke development (max) l/ 1 Shrinkage (percent max) I (machine direction) I (cross machine direction) I 200 100 300 300 50 55 Good 1-12 25 w/weight 2 3 No change 6/ 25 50 2 1 I I I I I I I I I I I I I I I I I I I l I I I I I 200 I 100 I I 1000 1 I 100 I 95 I 1-12 I I 500 I Go

28、od I 50 I w/weight I I 21 I 3 I I 6/ I 25 I 50 I I 21 1.5 I No change I I I I I I The exposed sample shall not show appreciable change after the prescribed hours of exposure. Cycles are defined as “double rubs. I Abrasive medium: 220 grit silicon carbon-coated abrasive sheet. Perform this test dry;

29、the wall covering shall achieve as a minimum a “good. I Nonwoven supporting material shall be bonded to the wearing surface. When an attempt is made to pull the wearing surface from the backing by hand, the backing shall delaminate or break before failure of the bonding. To pass, the tested sample s

30、hall not become stiff, brittle, soft, tacky, discolored, or show loss of grain. For shipboard applications, the fire performance criteria shall be in accordance with MIL-STD-1623. 3.5 Coating compound. The coating shall be formulated from polymerized or copolymerized vinyl chloride resin, suitably p

31、lasticized, stabilized, and pigmented. 3.5.1 TOR coating. When necessary to meet the requirements of table I, a clear top coating or film may be used. Coating shall be uniform in thickness and free of blisters. O 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license

32、from IHS-,-,-CCC-W-408D 3.6 Mildew resistant. When specified (see 6.2), the wall covering shall be mildew resistant. Wallcovering described as mildew resistant shall be protected to resist (fungal) mildew growth on the decorative surface to achieve a rating of O or 1 when tested in accordance with 4

33、.4.8. 3.7 Fire ratinq. Unless otherwise specified (see 6.2), the flame spread and the smoke development shall be as stated in table I. 3.8 Finish. The surface texture, pattern, color, and grain of the vinyl-coated wall covering shall be as specified (see 6.2). 3.9 Length and width. The length and wi

34、dth of the wall covering shall be as specified (see 6.2 and 6.6). 3.10 Marking. Each roll shall have two identical labels, one inside the wrapping and one outside the wrapping. The labels shall indicate gross length, piece length, pattern, and color identification. 3.11 WorkmanshiD. The vinyl-coated

35、 wall covering shall conform to the quality and grade of product established by this specification. 3.12 Definitions. Terms used in this specification are defined in 6.7. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the contract or purchase order,

36、the contractor is responsible for the performance of all inspection requirements (examinations and tests) as specified herein. Except as otherwise specified in the contract or purchase order, the contractor may use his own or any other facilities suitable for the performance of the inspection requir

37、ements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in this specification where such inspections are deemed necessary to ensure supplies and services conform to prescribed requirements. 4.1.1 Responsibility for

38、compliance. All items shall meet all requirements of sections 3 and 5. The inspection set forth in this specification shall become a part of the contractors overall inspection system or quality program. The absence of any inspection requirements in the specification shall not relieve the contractor

39、of the responsibility of ensuring that all products or supplies submitted to the Government for acceptance comply with all requirements of the contract, Sampling inspection, as part of manufacturing operations, is an acceptable practice to ascertain conformance to requirements, however, this does no

40、t authorize submission of known defective material, either indicated or actual, nor does it commit the Government to accept defective material. 4.2 Classification of inspections. The inspection requirements specified herein are classified as follows: a. First article inspection (see 4.2.1). b. Quali

41、ty conformance inspection (see 4.2.2). c. Preparation for delivery inspection (see 4.5) 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-CCC-W-408D M 9999974 OLb2275 706 CCC-W-408D 4.2.1 First article inspection. The first article inspection shall b

42、e performed on one complete roll of vinyl-coated wall covering when a first article is required (see 6.2). This inspection shall include the examination of 4.3 and the tests of 4.4 through 4.4.7. When mildew test is specified (see 6.2), test 4.4.8 shall be performed. The first article may be either

43、a first production item or a standard production item from the suppliers current inventory provided the vinyl-coated wall covering meets the requirements of the specification and is representative of the design, construction, and manufacturing technique applicable to the remaining vinyl-coated wall

44、covering to be furnished under the contract. 4.2.1.1 First article tests. When first article is required (see 6.2), the first article shall be tested as specified in 4.4 through 4.4.7. The first article tests shall be performed by the contractor under the direction and in the presence of Government

45、representatives. Failure to pass any phase of the required tests shall be cause for rejection. 4.2.1.2 Waiver of first article tests. Unless otherwise specified (see 6.2), the first article testing will be waived provided the following conditions are met by the contractor. a. The same type of wall c

46、overing being offered must have previously been tested as specified in 4.4 through 4.4.7 and found to have met those test requirements. b. There shall have been no changes in the manufacturing techniques or materials which would affect the physical properties of the wall covering during or since the

47、 testing was performed. c. Records which verify these conditions for waiver must be maintained by the contractor and must be available for review by an authorized contracting officers representative. When agreed to by the contracting officer, a written statement from the contractor that the conditio

48、ns for waiver have been met, will be accepted in lieu of the first articletesting. 4.2.2 Oualitv conformance inspection. The quality conformance inspection shall include the examination of 4.3, the tests of 4.4 through 4.4.7, and the packaging inspection of 4.5. This inspection shall be performed on

49、 the samples selected in accordance with 4.3. 4.2.2.1 Inspection lot. A lot shall consist of each type of vinyl-coated wall covering offered for delivery at one time. 4.2.2.2 Sampling for examination. Sampling for this examination shall be in accordance with in MIL-STD-105. The sample unit shall be one complete fabricated roll of vinyl-coated wall covering. 4.2.2.3 SamDlinE for test. Sampling for test shall be in accordance with level S-1 of MIL-STD-105. The sample unit shall