DLA DESC-DWG-84168 REV E-2011 HOLDER ELECTRICAL CARD CARD GUIDE-RETAINER LEVER ACTUATED METAL.pdf

1、REVISIONS LTR DESCRIPTION DATE APPROVED A Page 10, add new paragraph 6.5, Patents. 24 OCT 1985 Ivan Jones B Added marking requirements. Editorial corrections throughout. 17 DEC 1987 Randy Larson C Corrected two dimensions on figure 1. Editorial corrections throughout. Added finger tab option. Added

2、dash numbers 81 through 152. 9 SEP 1988 Randy Larson D Change FSC from 5999 to 5998. Technical and editorial changes throughout. 14 SEP 2001 Thomas Hess E Updated referenced documents and contact information. Technical and editorial changes throughout. 25 FEB 2011 David Corbett Prepared in accordanc

3、e with ASME Y14.100 Source control drawing REV PAGE REV STATUS OF PAGES REV E E E E E E E E E E E E E E E PAGE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 PMIC N/A PREPARED BY DESIGN ACTIVITY DEFENSE ELECTRONICS SUPPLY CENTER, DAYTON, OH 454445000 Christopher Rauch Original date of drawing CHECKED BY TITLE

4、Randy Larson HOLDER, ELECTRICAL CARD, CARD GUIDE- RETAINER, LEVER ACTUATED, METAL APPROVED BY Ivan Jones SIZE CAGE CODE DWG. NO. 84168 A 14933 REV PAGE 1 OF 9 AMSC N/A 5998E053CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 DEFENSE LOGISTICS AGENCY DLA LAND AND MARITIME, OHIO 432183990 Provided by IHSNot fo

5、r ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 454445000 SIZE CODE IDENT NO. DWG NO. A 14933 84168 REV E PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for a family of lever actuated card guides intended f

6、or use with printed circuit boards and circuit card assemblies in moderate shock and vibration environments. 1.2 Part or Identifying Number (PIN). The complete PIN shall be as follows: 84168 Drawing number 152 Dash number (see table I) T Optional finger Tab (see 3.1.1) E Optional housing finish (see

7、 3.3) 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3, 4, or 5 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effo

8、rt has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents cited in sections 3, 4, or 5 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbo

9、oks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract (see 6.2). SPECIFICATIONS FEDERAL FFR556 Rivet, Solid, Small; Rivet, Spli

10、t, Small; Rivet Tubular, Small; Flat Washer (Burr); and Cap, Rivet; General Purpose. STANDARDS DEPARTMENT OF DEFENSE MILSTD1285 Marking of Electrical and Electronic Parts. Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or https:/assist.daps.dla.mil or from

11、the Standardization Document Order Desk, 700 Robbins Avenue, Philadelphia, PA 191115094.) 2.3 Non-Government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitatio

12、n or contract (see 6.2). ASTM INTERNATIONAL (ASTM) ASTM A366/A366M Standard Specification for Commercial Steel (CS) Sheet, Carbon, (0.15 Maximum Percent), ColdRolled. ASTM B194 Standard Specification for CopperBeryllium Alloy Plate, Sheet, Strip, and Rolled Bar. ASTM B700 Standard Specification for

13、Electrodeposited Coatings of Silver for Engineering Use. (Copies of these documents are available online at http:/www.astm.org or from the ASTM International, P.O. Box C700, 100 Barr Harbor Drive, West Conshohocken, PA 194282959.) Provided by IHSNot for ResaleNo reproduction or networking permitted

14、without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 454445000 SIZE CODE IDENT NO. DWG NO. A 14933 84168 REV E PAGE 3 SOCIETY OF AUTOMOTIVE ENGINEERS (SAE) SAE AMSQQP416 Plating Cadmium (Electrodeposited). SAE AMSQQN290 Nickel Plating (Electrodeposited). (Application for copies

15、should be addressed to the SAE World Headquarters, 400 Commonwealth Drive, Warrendale, PA 150960001 or at URL: http:/www.sae.org/) (Non-Government standards and other publications are normally available from the organizations which prepare or which distribute the documents. These documents also may

16、be available in or through libraries or other informational services.) 2.4 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this

17、document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Interface and physical dimensions. See table I and figures 1 and 2. 3.1.1 Finger tab. An optional finger tab on the operating lever is available (see figure 2). 3.2 Materi

18、als. 3.2.1 Housing. The body material shall be cold rolled steel in accordance with ASTM A366/A366M or beryllium copper in accordance with ASTM B194. 3.2.2 Rivets. Rivet material shall be type XII, grade E for steel housing material or type XII, grade A or F, for beryllium copper housing material in

19、 accordance with FFR556. Rivets shall be .065 inch (1.65 mm) in diameter. 3.3 Finish. The card guide housing finish shall be either cadmium plate in accordance with SAEAMSQQvP416, type II, class 2 or silver in accordance with ASTM B700 or nickel plate in accordance with SAEAMSQQN290, class 1, grade

20、G (bright). Card guides with a cadmium finish do not use a finish designator. Card guides with a silver finish shall include a suffix “E“ in the PIN. Card guides with a nickel plated finish shall include a suffix “N“ in the PIN (see 1.2) 3.4 Certificate of compliance. A certificate of compliance sha

21、ll be required from manufacturers requesting to be an approved source of supply. 3.5 Marking. Marking of the DESC PIN is not required on the card guide is not required; however, each unit package shall be marked in accordance with MILSTD1285 and include the PIN as specified herein (see 1.2), the man

22、ufacturers name or Commercial and Government Entity (CAGE) code, and date lot codes. 3.6 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceed

23、s the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.7 Workmanship. Card guides shall be processed in such a manner as to be uniform in quality and shall be free from surface and finish flaws that could affect life or serviceability. Card guides

24、shall be free of flash, pits, voids, and excessive mold marks. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 454445000 SIZE CODE IDENT NO. DWG NO. A 14933 84168 REV E PAGE 4 FIGURE 1. Design and dimensio

25、ns. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 454445000 SIZE CODE IDENT NO. DWG NO. A 14933 84168 REV E PAGE 5 FIGURE 2. Design and dimensions Continued. Provided by IHSNot for ResaleNo reproduction

26、or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 454445000 SIZE CODE IDENT NO. DWG NO. A 14933 84168 REV E PAGE 6 Inches mm Inches mm Inches mm Inches mm .001 .003 .005 .015 .02 .067 .073 .09 .093 .103 .142 .157 .165 .180 0.025 0.076 0.13 0.25 0.5 1.7

27、0 1.85 2.3 2.36 2.61 3.61 3.99 4.19 4.57 .19 .196 .210 .218 .250 .290 .297 .30 .320 .327 .500 .67 .750 2.250 3.250 4.8 4.98 5.33 5.54 6.35 7.37 7.54 7.62 8.13 8.31 12.70 17.0 19.05 57.15 82.55 4.250 4.750 5.00 5.250 5.50 5.750 6.00 6.250 6.50 6.750 7.00 7.250 7.50 7.750 8.00 107.95 120.65 127.0 133.

28、35 139.7 146.05 152.4 158.75 165.1 171.45 177.8 184.15 190.5 196.85 203.2 8.250 8.50 8.750 9.00 9.250 9.50 9.750 10.00 10.250 10.50 10.750 11.00 11.250 11.50 12.00 209.55 215.9 222.25 228.6 234.95 241.3 247.65 254 260.35 266.7 273.05 279.4 285.75 292.1 304.8 NOTES: 1. Dimensions are in inches. Metri

29、c equivalents are given for general information only. 2. Unless otherwise specified, tolerance is .02 inch (0.51 mm) for two place decimals and .010 inch (0.25 mm) for three place decimals. 3. All parts include extractor flange. 4. Center mounting hole and cutout are eliminated on lengths under 5 in

30、ches (127.0 mm). FIGURE 1. Dimensions of card holders Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 454445000 SIZE CODE IDENT NO. DWG NO. A 14933 84168 REV E PAGE 7 FIGURE 2. Optional finger t

31、ab details. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 454445000 SIZE CODE IDENT NO. DWG NO. A 14933 84168 REV E PAGE 8 TABLE I. Design and dimensions. PIN 84168 Housing material B = beryllium copper

32、S = Steel Board thickness (inches) A = .0625 (1.58 mm) B = .0937 (2.38 mm) “L“ Dimension Inches (mm) Lever action Left or right L = left R = right 001 B A 3.0 (76.2) L 002 S A “ L 003 B B “ L 004 S B “ L 005 B A “ R 006 S A “ R 007 B B “ R 008 S B “ R 009 B A 3.5 (88.9) L 010 S A “ L 011 B B “ L 012

33、 S B “ L 013 B A “ R 014 S A “ R 015 B B “ R 016 S B “ R 017 B A 4.0 (101.6) L 018 S A “ L 019 B B “ L 020 S B “ L 021 B A “ R 022 S A “ R 023 B B “ R 024 S B “ R 025 B A 4.5 (114.3) L 026 S A “ L 027 B B “ L 028 S B “ L 029 B A “ R 030 S A “ R 031 B B “ R 032 S B “ R 033 B A 5.0 (127.0) L 034 S A “

34、 L 035 B B “ L 036 S B “ L 037 B A “ R 038 S A “ R 039 B B “ R 040 S B “ R Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 454445000 SIZE CODE IDENT NO. DWG NO. A 14933 84168 REV E PAGE 9 TABLE I. Design a

35、nd dimensions Continued. PIN 84168 Housing material B = beryllium copper S = Steel Board thickness (inches) A = .0625 (1.58 mm) B = .0937 (2.38 mm) “L“ Dimension Inches (mm) Lever action Left or right L = left R = right 041 B A 5.5 (139.7) L 042 S A “ L 043 B B “ L 044 S B “ L 045 B A “ R 046 S A “

36、R 047 B B “ R 048 S B “ R 049 B A 6.0 (152.4) L 050 S A “ L 051 B B “ L 052 S B “ L 053 B A “ R 054 S A “ R 055 B B “ R 056 S B “ R 057 B A 7.0 (177.8) L 058 S A “ L 059 B B “ L 060 S B “ L 061 B A “ R 062 S A “ R 063 B B “ R 064 S B “ R 065 B A 7.5 (190.5) L 066 S A “ L 067 B B “ L 068 S B “ L 069

37、B A “ R 070 S A “ R 071 B B “ R 072 S B “ R 073 B A 8.5 (215.9) L 074 S A “ L 075 B B “ L 076 S B “ L 077 B A “ R 078 S A “ R 079 B B “ R 080 S B “ R Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 4544450

38、00 SIZE CODE IDENT NO. DWG NO. A 14933 84168 REV E PAGE 10 TABLE I. Design and dimensions Continued. PIN 84168 Housing material B = beryllium copper S = Steel Board thickness (inches) A = .0625 (1.58 mm) B = .0937 (2.38 mm) “L“ Dimension Inches (mm) Lever action Left or right L = left R = right 081

39、B A 6.5 (165.1) L 082 S A “ L 083 B B “ L 084 S B “ L 085 B A “ R 086 S A “ R 087 B B “ R 088 S B “ R 089 B A 8.0 (203.2) L 090 S A “ L 091 B B “ L 092 S B “ L 093 B A “ R 094 S A “ R 095 B B “ R 096 S B “ R 097 B A 9.0 (228.6) L 098 S A “ L 099 B B “ L 100 S B “ L 101 B A “ R 102 S A “ R 103 B B “

40、R 104 S B “ R 105 B A 9.5 (241.3) L 106 S A “ L 107 B B “ L 108 S B “ L 109 B A “ R 110 S A “ R 111 B B “ R 112 S B “ R 113 B A 10.0 (254.0) L 114 S A “ L 115 B B “ L 116 S B “ L 117 B A “ R 118 S A “ R 119 B B “ R 120 S B “ R Provided by IHSNot for ResaleNo reproduction or networking permitted with

41、out license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 454445000 SIZE CODE IDENT NO. DWG NO. A 14933 84168 REV E PAGE 11 TABLE I. Design and dimensions Continued. PIN 84168 Housing material B = beryllium copper S = Steel Board thickness (inches) A = .0625 (1.58 mm) B = .0937 (2.38 mm)

42、 “L“ Dimension Inches (mm) Lever action Left or right L = left R = right 121 B A 10.5 (266.7) L 122 S A “ L 123 B B “ L 124 S B “ L 125 B A “ R 126 S A “ R 127 B B “ R 128 S B “ R 129 B A 11.0 (279.4) L 130 S A “ L 131 B B “ L 132 S B “ L 133 B A “ R 134 S A “ R 135 B B “ R 136 S B “ R 137 B A 11.5

43、(292.1) L 138 S A “ L 139 B B “ L 140 S B “ L 141 B A “ R 142 S A “ R 143 B B “ R 144 S B “ R 145 B A 12.0 (304.8) L 146 S A “ L 147 B B “ L 148 S B “ L 149 B A “ R 150 S A “ R 151 B B “ R 152 S B “ R Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-D

44、EFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 454445000 SIZE CODE IDENT NO. DWG NO. A 14933 84168 REV E PAGE 12 4. VERIFICATION 4.1 Sampling and inspection. Unless otherwise specified in the contract or purchase order, the contractor is responsible for the performance of all inspection requirements as

45、 specified herein. Except as otherwise specified in the contract, the contractor may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspect

46、ions set forth in this drawing where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. 4.2 Conformance inspections. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of visual and mechanical inspections

47、of interface and physical dimensions (see 3.1), materials (see 3.2), and workmanship (see 3.7). Criteria for defects are listed in 4.2.5. 4.2.2 Optional statement of compliance. The acquiring activity, at its discretion, may accept a statement of compliance in lieu of the manufacturer performing the inspection of product for delivery (see 6.2.b). 4.2.3 Sampling plan. A sample of parts shall be randomly selected in accordance with table II, normal sampling. If one or more defects are found, the lot shall be rejected. Criteria for defects are listed in 4.2.5