ImageVerifierCode 换一换
格式:PDF , 页数:10 ,大小:89.62KB ,
资源ID:688331      下载积分:10000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-688331.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(DLA DESC-DWG-85006 REV F-2012 RELAY SOLID STATE HERMETICALLY SEALED OPTICALLY ISOLATED 1 0 AMPERE 60 V DC SPST (N 0 ) CMOS INPUT.pdf)为本站会员(twoload295)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

DLA DESC-DWG-85006 REV F-2012 RELAY SOLID STATE HERMETICALLY SEALED OPTICALLY ISOLATED 1 0 AMPERE 60 V DC SPST (N 0 ) CMOS INPUT.pdf

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Changed manufacturers eligibility. 24 Aug 1987 Steven B. Searcy B Changes in accordance with NOR 5945-R004-93 4 Aug 1993 R. Gosciniak C Cancel document 3 Mar 2000 Kendall Cottongim D Reinstate document 19 July 2002 Kendall Cottongim E Incorporated boilerpla

2、te updates. Modified can height of Figure 1. Added approved source of supply. 17 July 2008 Michael A. Radecki F Incorporate boilerplate updates. Added approved source of supply. 05 Nov 2012 Michael A. Radecki Prepared in accordance with ASME Y14.100 Source control drawing REV STATUS OF PAGES REV F F

3、 F F F F F F F F PAGES 1 2 3 4 5 6 7 8 9 10 PMIC N/A PREPARED BY Richard A. Yannitti DESIGN ACTIVITY DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444-5000 Original date of drawing 15 Aug 1985 CHECKED BY James R. Martin TITLE RELAY, SOLID STATE, HERMETICALLY SEALED, OPTICALLY ISOLATED, 1.0 AMPERE,

4、60 V DC, SPST (N.0.), CMOS INPUT APPROVED BY Steven B. Searcy SIZE A CODE IDENT. NO. 037Z3 DWG NO. 85006 REV F PAGE 1 OF 10 AMSC N/A 5945-2012-E01 CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 DEFENSE LOGISTICS AGENCY DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 Provided by IHSNot for ResaleNo reproduc

5、tion or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85006 REV F SHEET 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for a hermetically sealed solid state relay supplied to the “Y“ screening requi

6、rements of MIL-PRF-28750. 1.2 Part or Identifying Number (PIN). The complete PIN shall be as follows: 85006 -01 Drawing number Dash number 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include

7、documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness o+ this list, document users are cautioned that they must meet all specified requirements of documents in sections 3 and 4 of

8、this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents

9、are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-28750 Relays, Solid State, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-202 - Electronic and Electrical Component Parts. MIL-STD-883 - Microelectronics. MIL-STD-1285 - Marking of Elect

10、rical and Electronic Parts, FSC: 59GP 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence, unless otherwise noted. Nothing in this document, however, supersedes applicable laws and regulatio

11、ns unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-28750, and as specified herein. 3.2 Interface and physical dimensions. The interface and physical dimensions shall be as specified in MIL-PRF-

12、28750, and herein (see figure 1). 3.3 Input characteristics. 3.3.1 Input current. 16 milliamperes dc maximum. 3.3.2 Control voltage range. 3.8 V dc to 32 V dc maximum. 3.3.3 Rated turn on voltage. 5.0 V dc. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS

13、-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85006 REV F SHEET 3 NOTES; 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, tolerances are .005 (0.13 mm) for three place decimals and .01

14、(0.3 mm) for two place decimals. 4. Circuit diagram shown on part is terminal view. FIGURE 1. Outline dimensions and configuration. Ltr Inches Millimeter Min Max Min Max A - .335 - 8.51 B - .290 - 7.37 C .70 - 17.8 - D .016 .019 0.41 0.48 E .090 .110 2.29 2.79 F .080 .090 2.03 2.29 G .090 .110 2.29

15、2.79 H .070 .090 1.78 2.29 J - .370 - 9.40 K .030 .034 0.76 0.86 L .029 .033 0.74 0.84 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85006 REV F SHEET 4 FIGURE 2. Ou

16、tput current versus ambient temperature. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85006 REV F SHEET 5 NOTES: 1. tON= tdON+ tr. 2. tOFF= tdOFF+ tf. FIGURE 3. Tur

17、n-on and turn-off time waveform. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85006 REV F SHEET 6 NOTE: Limiting resistor required over 6 volts (see table above) wh

18、en not used with a heat sink; with a heat sink, the values are to be determined. FIGURE 4. Wiring diagram. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85006 REV F

19、SHEET 7 3.3.4 Maximum turn-off voltage (assured). 1.5 V dc maximum. 1/ 3.3.5 Minimum turn-on voltage (assured). 3.8 V dc minimum. 1/ 3.3.6 Reverse polarity. 32 V dc maximum. 3.4 Output characteristics. 3.4.1 Continuous operating output voltage (maximum). 60 V dc maximum. 3.4.2 Output current at 25C.

20、 1.0 ampere dc maximum. 3.4.2.1 Rated output current. See figure 2. 3.4.3 Output capacitance. 700 pF at 25 V ac, 1 MHz, superimposed. 3.4.3.1 Input-output capacitance. 5 pF maximum, 1 KHz. 3.4.4 Output leakage current. 10 microamperes dc maximum at 60 V dc, -55C to +25C. 40 microamperes maximum at 3

21、0 V dc, 100C. Allow 10 seconds for measurement to settle. 3.4.5 Transient voltage. 80 V dc maximum, 5 seconds maximum pulse duration (leakage less than 1.0 mA). 3.4.6 On resistance. .3 ohm maximum (measured at 100 mA at 25C.) NOTE: For on state resistance at temperatures other than 25C, use the foll

22、owing equation: R = R25X e0.006 X %Twhere: R25= resistance at 25C from figure 4. R = resistance at new temperature %T = new temperature - 25C e = 2.7182818 3.4.7 Output voltage drop. 0.5 V dc maximum. 3.4.8 Short circuit protection. 3.4.8.1 Relay will not be damaged by a short on the load during nor

23、mal operation or by being turned on into a shorted load. 3.4.8.2 Relay will not be damaged by continuous overload condition. 3.4.8.3 To return unit to normal operating condition, remove short circuit or overload condition. Then remove and reapply input control voltage or remove and reapply load volt

24、age. 3.4.9 Overload. 200 percent of rated current for 50 milliseconds. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85006 REV F SHEET 8 3.5 Electrical characteristi

25、cs. 3.5.1 Dielectric withstanding voltage. 1,000 V rms (input to output to case). 3.5.2 Insulation resistance. 1,000 megohms (input to case at 500 V dc). 3.5.3 Turn-on time (tON). 1.8 milliseconds maximum (see figure 3). 3.5.4 Turn-off time (tOFF). 1.1 milliseconds maximum (see figure 3). 3.5.5 Maxi

26、mum repetitive rate. 20 Hz, 50 percent duty cycle. 3.5.6 On-resistance. 0.52 ohm maximum and 0.225 ampere. 3.5.7 Electromagnetic interference. Applicable. 3.6 Environmental characteristics. 3.6.1 Operating temperature range. -55C to +100C. 3.6.2 Storage temperature range. -55C to +125C. 3.6.3 Shock.

27、 MIL-STD-202, method 213, test condition F, 1,500 Gs for 0.5 millisecond. Relays shall have rated turn on voltage applied. 3.6.4 Vibration. MIL-STD-202, method 204, test condition D 100 Gs, 10 to 3,000 Hz. Relays shall have rated turn voltage applied. 3.6.5 Acceleration. MIL-STD-883, method 2001, te

28、st condition A, 5,000 Gs, Y1 axis. 3.6.6 Seal (hermetic). MIL-STD-883, method 1014, test condition B. 3.7 Physical. Physical requirements shall be as specified herein. 3.7.1 Weight. 2 grams (0.07 ounce) maximum. 3.7.2 Wiring diagram. See figure 4. 3.8 Marking. Marking shall be in accordance with MIL

29、-PRF-28750 except the PIN shall be in accordance with 1.2 herein. The “M28750/X-XXXY“ part number shall not be used. 3.9 Assurance requirements. Relays furnished under this drawing shall have been subjected to, and passed all the requirements, tests, and inspections detailed herein. 3.9.1 Conformanc

30、e inspection. Conformance inspection shall be in accordance with MIL-PRF-28750 and 4.2 herein. 3.10 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meet

31、s or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3. 11 Manufacturer eligibility. To be eligible for listing as an approved source of supply, a manufacturer shall be listed on the MIL-PRF-28750 Qualified Product List for at least one

32、part, or perform the Group A inspection specified herein on a sample of parts agreed upon by the manufacturer and DLA Land and Maritime-VA. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDE

33、NT NO. 14933 DWG NO. 85006 REV F SHEET 9 3.12 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply (see 6.6). 3.13 Pure tin. The use of pure tin, as an underplate or final finish is prohibited both internal

34、ly and externally. Tin content of components and solder shall not exceed 97 percent, by mass. Tin shall be alloyed with a minimum of 3 percent lead, by mass (see 6.5). 3.14 Marking. Marking shall be in accordance with MIL-STD-1285, except the relay shall be marked with the PIN as specified herein (s

35、ee 1.2), the manufacturers name of Commercial and Government Entity (CAGE) code, and date lot codes. 3.15 Workmanship. The relay shall be uniform in quality and free from any defects that will affect life, serviceability, or appearance. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspe

36、ction procedures shall be in accordance with MIL-PRF-28750, except as modified herein. 4.2 Conformance inspection. Conformance inspection shall be in accordance with group A listing of MIL-PRF-28750. Group A testing shall be performed on each inspection lot and manufacturers shall keep lot records f

37、or 3 years (minimum), monitor for compliance to the prescribed procedures, and observe that satisfactory manufacturing conditions and records on lots are maintained for these relays. 4.2.1 Group A inspection. Group A inspection shall consist of all tests specified in MIL-PRF-28750 for the “Y“ screen

38、ing level, components used internally to the relay shall not require hermetic packaging. Temperature range for screening tests shall be as specified in 3.6.1. 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). Wh

39、en packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activities within the Military

40、Service or Defense Agency, or within the military services system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains

41、 information of a general or explanatory nature which may be helpful, but is not mandatory.) 6.1 Intended use. Relays conforming to this drawing are intended for use when military specifications do not exist and qualified military devices that will perform the required function are not available for

42、 O.E.M. application. This drawing is intended exclusively to prevent the proliferation of unnecessary duplicate specifications, drawings, and stock catalog listings. When a military specification exists and the product covered by this drawing has been qualified for listing on QPL-28750, this drawing

43、 will become inactive for new design. The QPL-28750 product shall be the preferred item for all applications. 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery of one copy of the conformance inspection data or the

44、certificate of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Requirements for packaging and packing. 6.3 Replaceability. Relays covered by this drawing will replace the same generic device covered by a contractor-prepared specification o

45、r drawing. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85006 REV F SHEET 10 6.4 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by

46、mass, may exhibit tin whisker growth problems after manufacture. Tin whiskers may occur anytime from a day to years after manufacture and can develop under typical operating conditions, on products that use such materials. Conformal coatings applied over top of a whisker-prone surface will not preve

47、nt the formation of tin whiskers. Alloys of 3 percent lead, by mass, have shown to inhibit the growth of tin whiskers. For additional information on this matter, refer to ASTM-B545 (Standard Specification for Electrodeposited Coatings of Tin). 6.5 Users of record. Coordination of this document for f

48、uture revisions is coordinated only with the approved source(s) of supply and the users of record of this document. Requests to be added as a recorded user of this drawing may be achieved online at mailto: relaydla.mil or if in writing to: DLA Land and Maritime, ATTN: DLA Land and Maritime/VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-4481 or DSN 850-4481. 6.6 Approved source(s) of supply. Approved source(s) of supply are listed herein. Additional sources will be added as they become available. Assistance in the use of

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1