DLA DESC-DWG-85031 REV A-1994 CONNECTOR RECEPTACLE ELECTRICAL GENERAL PURPOSE SINGLE GROUNDING 2 POLE 3 WIRE 15 AMPERE 125 VOLTS ENVIRONMENTAL《125伏特15安培二极三线环保的可接地单通用电力贮存连接器》.pdf

1、DESC-DWG-85031 REV A 9997795 0057914 312 LTR A I REVISIONS DESCRIPTION DATE, APPROVED Add new part number for receptacle supplied with cap. / PREPARED BY CHECKED BY Jeffery Bohannon Ron Gary APPROVED BY Don Seser The front page of this drawing has been reprinted. DEFENSE ELECTRONICS SUPPLY CENTER DA

2、YTON. OHIO TITLE CONNECTOR. RECEPTACLE, ELECTRICAL, GERNERAL PURPOSE, SINGLE. GROUNDING, 2 POLE. 3 WIRE. 15 AMPERE. 125 VOLTS. ENVI RONMENTAL. . PMIC N/A SIZE A Original date of drawing: 15 April 1986 CODE IDENT. NO. DWG NO. 85031 14933 DESC FORM 144 REV A PAGE 1 OF 4 JUL 91 AMSC N/A 5935-ES73 DISTR

3、IBUTION STATEMENT A. Approved for public release; distribution is unlimited. Licensed by Information Handling ServicesDESC-DWG-85031 REV A 9999995 0057935 259 J a Z 1- JE W oc ax xi- in m o O 4 OJ DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO FIGURE 1. Screw termination. SIZE CODE IDENT. NO. A I 14

4、933 DWG NO. 85031 PAGE 2 DESC FORM l44A JUL 91 Licensed by Information Handling ServicesDESC-DWG-85031 REV A 9999995 0057916 195 - SIZE A DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO REQUIREMENTS : Receptacle: Shall conform to the requirements of W-C-596 except as specified herein. Ground pin: Ins

5、ertion: Shall establish contact at least .125 inch before contact is made by either of the power pins. Insertion force: Shall not exceed 25 pounds. Withdrawal force: Shall be 15 pounds 110. Minimum current: Potential voltage drop: carrying a current of 15 amperes when tested in accordance with MIL-C

6、-5015. Color of terminals and heads of terminal screws: Shall have a continuous rating of 15 amperes at 120 volts, 60 hertz. Between the respective terminals of the connector shall not exceed 50 millivolts when Wide power terminal - White Narrow power terminal - Yellow Ground terminal - Green CODE I

7、DENT. NO. DWG NO. 14933 85031 REV A PAGE 3 (See figure 1) Ma teri a 1 s : Shells: Shall be of an aluminum alloy that meets the performance requirements of MIL-C-5015 Class R. Shells shall be finished in accordance with MIL-C-5015 Class R. Contacts: Shall be made of suitably conductive copper alloys

8、and shall be plated in accordance with NI-S-365. All contacting surfaces shall be smooth. Connector inserts: Shall be in accordance with W-C-596. Part number: 85031-1 (Connector only). 85031-2 (Connector and MS25043-O22 style Cap, with cadmium OD finish and sash chain will be suppl i ed) . Cap: MS25

9、043-22CA (MIL-C-5015) Cap only Replacement data: Drawing 85031 replaces MS25199 cancelled 20 May 1983. Intended use: Connectors conforming to this drawing are intended for use when military specifications do not exist and qualified devices that will perform the required function are not available fo

10、r OEM application. This drawing is intended exclusively to prevent the prol iferation of unnecessary duplicate specifications, drawings. and stock catalog listings. When a military specification exists and the product covered by this drawing has been qualified for listing on the QPL-W-C-596 this dra

11、wing will become inactive for new designs. The QPL-W-C-596 product shall be the preferred item for all applications. Licensed by Information Handling ServicesDESC-DWG-85031 REV A m 9999995 0057937 021 m Suggested source of supply: A suggested source of supply is listed herein. Additional sources wil

12、l be added as they become available. 45444, telephone (513)296-5391 or Fax (513)296-8868 For assistance in the use of this drawing, contact DESC-ELDI. 1507 Wilmington Pike, Dayton Ohio, DESC drawing part number 85031 - i 85031-2 Vendor CAGE number Vendor similar part number 1/ 77820 7-8648 77820 7-8648-5 Vendor CAGE number 77820 SIZE CODE IDENT. NO. A 14933 DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO Vendor name and address hphenol Corporation 40-60 Delaware Ave Sidney NY 13838 DWG NO. 85031 DESC FORM 1UA JUL 91 Licensed by Information Handling Services