DLA DESC-DWG-86092 REV B-2011 HOLDER ELECTRICAL CARD CARD GUIDE-RETAINER LEVER ACTUATED METAL FOR COLD PLATE MOUNTING.pdf

1、REVISIONS LTR DESCRIPTION DATE APPROVED A Change FSC from 5999 to 5998. Technical and editorial changes throughout. djc 14 SEP 2001 Thomas Hess B Updated referenced documents and contact information. Technical and editorial changes throughout. jc 31 MAR 2011 David Corbett Prepared in accordance with

2、 ASME Y14.100 Source control drawing REV PAGE REV STATUS OF PAGES REV B B B B B B B B B B B PAGE 1 2 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARED BY DESIGN ACTIVITY DEFENSE ELECTRONICS SUPPLY CENTER, DAYTON, OH 454445000 Frank Crivello. Original date of drawing 31 March 1987 CHECKED BY TITLE Dan McGrath HO

3、LDER, ELECTRICAL CARD, CARD GUIDE- RETAINER, LEVER ACTUATED, METAL, FOR COLD PLATE MOUNTING APPROVED BY Clarence Brizius SIZE CAGE CODE DWG. NO. 86092 A 14933 REV B PAGE 1 OF 11 AMSC N/A 5998E054CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 DEFENSE LOGISTICS AGENCY DLA LAND AND MARITIME, OHIO 432183990 Pr

4、ovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 454445000 SIZE CODE IDENT NO. DWG NO. A 14933 86092 REV B PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for a family of lever actuated car

5、d guides intended for use with printed circuit boards and circuit card assemblies in moderate shock and vibration environments. 1.2 Part or Identifying Number (PIN). The complete PIN shall be as follows: 86092 Drawing number XX Dash number (see table I) T Optional finger tab (see 3.1.1) E Housing fi

6、nish (see 3.2.1) 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3, 4, or 5 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While

7、 every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents cited in sections 3, 4, or 5 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards,

8、 and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract (see 6.2). SPECIFICATIONS FEDERAL FFR556 Rivet, Solid, Small;

9、Rivet, Split, Small; Rivet Tubular, Small; Flat Washer (Burr); and Cap, Rivet; General Purpose. DEPARTMENT OF DEFENSE MILF495 Finish, Chemical, Black, for Copper Alloys. MILS5002 Surface Treatments and Inorganic Coatings for Metal Surfaces of Weapon Systems. MILDTL13924 Coating, Oxide, Black, For Fe

10、rrous Metals. STANDARDS DEPARTMENT OF DEFENSE MILSTD1285 Marking of Electrical and Electronic Parts. Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or https:/assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Philadelph

11、ia, PA 191115094.) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 454445000 SIZE CODE IDENT NO. DWG NO. A 14933 86092 REV B PAGE 3 2.3 Non-Government publications. The following documents form a part of t

12、his document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract (see 6.2). ASTM INTERNATIONAL (ASTM) ASTM A366 Standard Specification for Commercial Steel (CS) Sheet, Carbon, (0.15 Maximum Percent), Cold-Rolled. A

13、STM B194 Standard Specification for Copper-Beryllium Alloy Plate, Sheet, Strip, and Rolled Bar. ASTM B700 Standard Specification for Electrodeposited Coatings of Silver for Engineering Use. (Copies of these documents are available online at http:/www.astm.org or from the ASTM International, P.O. Box

14、 C700, 100 Barr Harbor Drive, West Conshohocken, PA 194282959.) SAE INTERNATIONAL (SAE) SAE AMSQQN290 Nickel Plating (Electrodeposited). SAE AMSQQP416 Plating Cadmium (Electrodeposited). SAE AMSC26074 Electroless Nickel Coatings. (Copies of these documents are available online at http:/www.sae.org o

15、r from SAE International, 400 Commonwealth Drive, Warrendale, PA 150960001.) (Non-Government standards and other publications are normally available from the organizations which prepare or which distribute the documents. These documents also may be available in or through libraries or other informat

16、ional services.) 2.4 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regu

17、lations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Interface and physical dimensions. See table I and figures 1 and 2. 3.1.1 Finger tab. An optional finger tab on the operating lever is available (see figure 2). 3.2 Materials. 3.2.1 Housing. The body material shall be cold ro

18、lled steel in accordance with ASTM A366/A366M or beryllium copper in accordance with ASTM B194. 3.2.2 Rivets. Rivet material shall be type XII grade E for steel housing material or type XII, grade A or F, for beryllium copper housing material in accordance with FFR556. Rivets shall be .065 inch (1.6

19、5 mm) in diameter. 3.3 Finish. 3.3.1 Housing. The finish shall be either cadmium plate in accordance with SAE AMSQQ-P-416, type II, class 2, silver in accordance with ASTM B700, or nickel plate in accordance with SAE AMSQQ-N-290, class 1, grade G (bright). For ebonal finish, the finish shall be in a

20、ccordance with MILF495 for beryllium copper card guide housings, or MILDTL13924 for steel card guide housings. Card guides with a cadmium plated finish shall do not use a finish designator in the PIN. Card guides with a silver finish shall include a suffix “A“ in the PIN. Card guides with an ebanol

21、finish shall include a suffix “E“ in the PIN. Card guides with a nickel plated finish shall include a suffix “N“ in the PIN (see 1.2). 3.4 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be an approved source of supply. 3.5 Marking. Marking o

22、f the DESC PIN is not required on the card guide is not required; however, each unit package shall be marked in accordance with MILSTD1285 and include the PIN as specified herein (see 1.2), the manufacturers name or Commercial and Government Entity (CAGE) code, and date lot codes. Provided by IHSNot

23、 for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 454445000 SIZE CODE IDENT NO. DWG NO. A 14933 86092 REV B PAGE 4 TABLE I. Design and dimensions. PIN 86092 Housing material B = beryllium copper S = Steel “L“ Dimension Inches

24、 (mm) Lever action Left or right L = left R = right 01 B 3.0 (76.2) L 02 S “ L 03 B “ R 04 S “ R 05 B 3.5 (88.9) L 06 S “ L 07 B “ R 08 S “ R 09 B 4.0 (101.6) L 10 S “ L 11 B “ R 12 S “ R 13 B 4.5 (114.3) L 14 S “ L 15 B “ R 16 S “ R 17 B 5.0 (127.0) L 18 S “ L 19 B “ R 20 S “ R 21 B 5.5 (139.7)“ L

25、22 S “ L 23 B “ R 24 S “ R 25 B 6.0 (152.4) L 26 S “ L 27 B “ R 28 S “ R 29 B 7.0 (177.8) L 30 S “ L 31 B “ R 32 S “ R 33 B 7.5 (190.5) L 34 S “ L 35 B “ R 36 S “ R 37 B 8.0 (203.2) L 38 S “ L 39 B “ R 40 S “ R Provided by IHSNot for ResaleNo reproduction or networking permitted without license from

26、 IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 454445000 SIZE CODE IDENT NO. DWG NO. A 14933 86092 REV B PAGE 5 FIGURE 1. Design and dimensions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444

27、5000 SIZE CODE IDENT NO. DWG NO. A 14933 86092 REV B PAGE 6 FIGURE 1. Design and dimensions Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 454445000 SIZE CODE IDENT NO. DWG NO. A 14933 86092 RE

28、V B PAGE 7 Inches mm Inches mm Inches mm Inches mm .001 .003 .005 .015 .02 .067 .073 .09 .093 .103 .142 .157 .165 .180 0.025 0.076 0.13 0.25 0.5 1.70 1.85 2.3 2.36 2.61 3.61 3.99 4.19 4.57 .19 .196 .210 .218 .250 .290 .297 .30 .320 .327 .500 .67 .750 2.250 3.250 4.8 4.98 5.33 5.54 6.35 7.37 7.54 7.6

29、2 8.13 8.31 12.70 17.0 19.05 57.15 82.55 4.250 4.750 5.00 5.250 5.50 5.750 6.00 6.250 6.50 6.750 7.00 7.250 7.50 7.750 8.00 107.95 120.65 127.0 133.35 139.7 146.05 152.4 158.75 165.1 171.45 177.8 184.15 190.5 196.85 203.2 8.250 8.50 8.750 9.00 9.250 9.50 9.750 10.00 10.250 10.50 10.750 11.00 11.250

30、11.50 12.00 209.55 215.9 222.25 228.6 234.95 241.3 247.65 254 260.35 266.7 273.05 279.4 285.75 292.1 304.8 NOTES: 1. Dimensions are in inches. Metric equivalents are given for general information only. 2. Unless otherwise specified, tolerance is .02 inch (0.51 mm) for two place decimals and .010 inc

31、h (0.25 mm) for three place decimals. 3. All parts include extractor flange. 4. Center mounting hole and cutout are eliminated on lengths under 5 inches (127.0 mm). FIGURE 1. Dimensions of card holders Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license fr

32、om IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 454445000 SIZE CODE IDENT NO. DWG NO. A 14933 86092 REV B PAGE 8 Inches mm Inches mm Inches mm Inches mm .001 .003 .067 .09 0.025 0.076 1.70 2.3 .093 .165 .19 .218 2.36 4.19 4.8 5.54 .25 .29 .30 .35 6.4 7.4 7.6 8.9 .38 .50 .78 9.7 12.7 19.8 NOT

33、ES: 1. Dimensions are in inches. Metric equivalents are given for general information only. 2. Unless otherwise specified, tolerance is .02 inch (0.51 mm) for two place decimals and .010 inch (0.25 mm) for three place decimals. 3. All parts include extractor flange. 4. Center mounting hole and cutou

34、t are eliminated on lengths under 5 inches (127.0 mm). FIGURE 2. Optional finger tab details. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 454445000 SIZE CODE IDENT NO. DWG NO. A 14933 86092 REV B PAGE

35、9 3.6 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantage

36、ous life cycle costs. 3.7 Workmanship. Card guides shall be processed in such a manner as to be uniform in quality and shall be free from surface and finish flaws that could affect life or serviceability. Card guides shall be free of flash, pits, voids, and excessive mold marks. 4. VERIFICATION 4.1

37、Sampling and inspection. Unless otherwise specified in the contract or purchase order, the contractor is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified in the contract, the contractor may use his own or any other facilities suitable

38、for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in this drawing where such inspections are deemed necessary to assure supplies and services conform to prescribed r

39、equirements. 4.2 Conformance inspections. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of visual and mechanical inspections of interface and physical dimensions (see 3.1), materials (see 3.2), and workmanship (see 3.7). Criteria for defects are listed in

40、 4.2.5. 4.2.2 Optional statement of compliance. The acquiring activity, at its discretion, may accept a statement of compliance in lieu of the manufacturer performing the inspection of product for delivery (see 6.2.b). 4.2.3 Sampling plan. A sample of parts shall be randomly selected in accordance w

41、ith table II, normal sampling. If one or more defects are found, the lot shall be rejected. Criteria for defects are listed in 4.2.5. 4.2.4 Rejected lots. If an inspection lot is rejected after normal sampling inspection, the manufacturer may rework it to correct the defects, or screen out the defec

42、tive parts and resubmit for inspection. Resubmitted lots shall be inspected by selecting a random sample of parts in accordance with table II, tightened sampling. If one or more defects are found in this sample, the lot shall be rejected and shall not be supplied to this specification. Resubmitted l

43、ots which are acceptable shall be clearly identified as re-inspected lots. 4.2.5 Defective characteristics and properties. Dimensional characteristics are considered defective when out of tolerance. Physical and functional properties are considered defective when outside the specified minimum, maxim

44、um, or range as applicable. Workmanship characteristics are considered defective when they would be detrimental to the intended use, performance requirements, or environmental survival of the part. TABLE II. Sampling plan. Lot size Normal Tightened 2 to 25 3 5 26 to 50 5 6 51 to 90 6 7 91 to 150 7 1

45、1 151 to 280 10 13 281 to 500 11 16 501 to 1,200 15 19 1,201 to 3,200 18 23 3,201 to 10,000 22 29 10,001 and over 29 35 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 454445000 SIZE CODE IDENT NO. DWG NO.

46、 A 14933 86092 REV B PAGE 10 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsib

47、le packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activities within the Military Service or Defense Agency, or within the military services system commands. Packaging data retrieval is available from the managin

48、g Military Departments or Defense Agencys automated packaging files, CDROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general or explanatory nature which may be helpful, but is not mandatory.) 6.1 Intended use. Card holders conforming to this drawing are intended for use when performance specifications do not exist and qualified military devices that will