DLA DESC-DWG-88020 REV C-2011 RESISTOR NETWORK 6-PIN LEADLESS CHIP CARRIER.pdf

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Revise par. 3.4 and Section 5. Editorial changes throughout. 20 Dec 1994 D. Moore B Revise to present DoD policy requirements. Editorial corrections throughout. 27 Jul 2000 Kendall A. Cottongim C 5 year review cycle. Editorial corrections throughout 21 Sept

2、 2011 Prepared in accordance with ASME Y14.100 Source control drawing REV STATUS OF PAGES REV C C C C C C C C PAGES 1 2 3 4 5 6 7 8 PMIC N/A PREPARED BY Dennis L. Cross DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OH Original date of drawing: 26 APR 1988 CHECKED BY David E. Moore TITLE RESISTOR NETWORK,

3、 6-PIN, LEADLESS CHIP CARRIER APPROVED BY David E. Moore SIZE A CODE IDENT. NO. 14933 DWG NO. 88020 REV C PAGE 1 OF 7 AMSC N/A 5905-E619CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 DLA LAND AND MARITIME COLUMBUS OHIO 43218-3990 Provided by IHSNot for ResaleNo reproduction or networking permitted without

4、license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 88020 REV C PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for a 6-pin, leadless chip carrier, resistor network. 1.2 Part or Identifying Number (PIN). The complete PIN is as fo

5、llows: 88020 - 001 | | Drawing number Dash number 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications and standards. The following specifications, standards and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these d

6、ocuments are those listed in the cited in the solicitation or contract (see 6.2). DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-914 - Resistors Networks, Fixed, Film, Surface Mount, Nonestablished Reliability, and Established Reliability, General Specification For. DEPARTMENT OF DEFENSE STANDARDS MIL-

7、STD-1285 - Marking of Electrical and Electronic Parts. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094). 2.2 Order of precedence. Unless otherwise

8、noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein (except for related specification sheets), the text of this document takes precedence unless otherwise noted. Nothing in this document, however, supersedes applicable laws an

9、d regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-914 and as specified herein. 3.2 Interface and physical dimensions. The resistor shall meet the interface and physical dimensions a

10、s specified in MIL-PRF-914 and herein (see figure 1). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 88020 REV C PAGE 3 Inches mm Inches mm Inches mm Inches mm Inches

11、 mm .002 0.005 .020 0.051 .028 0.071 .050 0.127 .210 0.533 .003 0.008 .020 0.051 .030 0.076 .080 0.203 .004 0.010 .025 0.064 .035 0.089 .150 0.381 .010 0.025 .027 0.069 .040 0.102 .170 0.432 NOTES: 1. Dimensions are in inches. Metric equivalents are given for general information only. 2. Unless othe

12、rwise specified, tolerances are .005 (0.13 mm) for three decimal places and .010 (0.25 mm) for two decimal places. 3. The picturization of the style above is given as representative of the envelope of the item. Slight deviations from the outline shown, which are contained within the envelope and do

13、not alter the functional aspects of the device, are acceptable. 4. Terminal 1 indicator shall be a notch, dot, or the numeral 1. This should be located at a point that clearly indicates terminal 1 FIGURE 1. Resistor network. Provided by IHSNot for ResaleNo reproduction or networking permitted withou

14、t license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 88020 REV C PAGE 4 3.3 Electrical characteristics. 3.3.1 Resistance. The resistance shall be as specified in table I. 3.3.2 Resistance tolerance. Resistors are available in (F) 1 percent toleran

15、ce. TABLE I. Resistance values. Dash number Resistance (in kohms) R1 R2 R3 R4 001 1.0 1.0 1.0 1.0 002 1.0 10.0 4.32 2.0 003 1.0 2.981 N/A N/A 004 1.0 1.82 N/A N/A 005 1.0 3.41 N/A N/A 006 1.0 6.94 N/A N/A 007 2.74 1.0 N/A N/A 008 2.0 2.0 2.2 N/A 3.3.3 Ratio accuracy. The ratio accuracy shall be 0.02

16、 percent for -001 and 0.05 percent for the remaining dash numbers. 3.3.4 Power rating. The power rating shall be 0.10 watt at 70OC derated to zero power at 125OC in accordance with figure 2. FIGURE 2. Derating curve 3.3.5 Package power rating. The package power rating shall be 0.10 watt times the nu

17、mber of individual elements. 3.3.6 Schematic. The schematic of the resistor network shall be identified as shown on figure 3. The resistor element RREFshall be the reference resistor element used in determining the ratio accuracy (when applicable). -60 -40 -20 0 20 60 80 100 120 140 160 180 Temperat

18、ure (OC) 125OC 100 80 60 40 20 0 70OC -55OC Percentofrated powerProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 88020 REV C PAGE 5 3.3.7 Operating voltage. The maximum

19、 operating voltage shall be 30 Vdc. 3.3.8 Operating temperature. The operating temperature shall be -55OC to +125OC. 3.3.9 Resistance temperature characteristic. The resistance temperature characteristic shall conform to characteristic “V” of MIL-PRF-914. NOTE: Pins 2 and 5 are unused for dash numbe

20、rs 003 through 008. FIGURE 3 Schematic. 3.3.10 TC tracking. The TC tracking shall be 5 ppm/OC. 3.4 Pure tin. The use of pure tin, as an underplate or final finish, is prohibited both internally and externally. Tin content of resistor components and solder shall not exceed 97 percent, by mass. Tin sh

21、all be alloyed with a minimum of 3 percent lead, by mass (see 6.3). - Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 88020 REV C PAGE 6 3.5 Marking. Marking shall be

22、in accordance with MIL-STD-1285, except the PIN shall be as specified in 1.2, with the manufacturers CAGE number or trade mark and date code. 3.6 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum e

23、xtent possible provided that the material meets or exceeds the operational and maintenance requirements and promotes economically advantageous life cycle costs. 3.7 Manufacturer eligibility. To be eligible for listing as a approved source of supply, a manufacturer shall be listed on the MIL-PRF-914

24、Qualified Products List for at least one part, or perform the group A and group B inspections specified herein on a sample of parts agreed upon by the manufacturer and DLA Land and Maritime - VA. 3.7.1 Certificate of compliance. A certificate of compliance shall be required from manufacturers reques

25、ting to be listed as a suggested source of supply. 3.8 Workmanship. Resistors shall be uniform in quality and free from any defects that will affect life, serviceability, or appearance. 4. VERIFICATION 4.1 Qualification inspection. Qualification inspection in accordance with MIL-PRF-914 is not appli

26、cable to this document. 4.1.1 Failure rate qualification. The failure rate qualification specified in MIL-PRF-914 is not applicable to this document. 4.2 Conformance inspections. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of group A and group B inspect

27、ions of MIL-PRF-914. 4.2.2 Certification. The acquiring activity, at its discretion, may accept a certificate of compliance with group B requirements in lieu of performing group B tests (see 6.2d). 4.4 Inspection of packaging. Inspection of packaging shall be in accordance with MIL-PRF-914. 4.5 Visu

28、al and mechanical examination. Resistors shall be examined to verify that the materials, design, construction, physical dimensions, marking, and workmanship are in accordance with the applicable requirements of MIL-PRF-914. 5. PACKAGING 5.1 Packaging. For acquisition purpose, the packaging requireme

29、nts shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the In

30、ventory Control Points packaging activities within the Military Service or Defense Agency, or within the military services system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the

31、 responsible packaging activity. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 88020 REV C PAGE 7 6. NOTES (This section contains information of a general or explana

32、tory nature that may be helpful, but is not mandatory.) 6.1 Intended use. Resistor networks are used in surface mounting applications where space is a major concern. 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for deliver

33、y: One copy of the conformance inspection data or a certificate of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Packaging requirements (see 5.1). (i.e. Electrostatic discharge sensitive packaging). d. Whether the manufacturer performs t

34、he group B tests or provides certificate of compliance with group B (see 4.2.2). 6.3 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker growth problems after manufacture. Tin whiskers may occur anytime from a day to years after manufactur

35、e and can develop under typical operating conditions, on products that use such materials. Conformal coatings applied over top of a whisker-prone surface will not prevent the formation of tin whiskers. Alloys of 3 percent lead, by mass, have shown to inhibit the growth of tin whiskers. For additiona

36、l information on this matter, refer to ASTM-B545 (Standard Specification for Electrodeposited Coatings of Tin). 6.4 Electrostatic charge. Under several combinations of conditions, these resistors can be electrically damaged, by electrostatic charges, and drift from specified value. Users should cons

37、ider this phenomena when ordering or shipping resistors. Direct shipment to the Government is controlled by MIL-DTL-39032 that specifies a preventive packaging procedure 6.5 Pulse applications. Designers are CAUTIONED on using these resistors in pulse applications. Since they have not been qualified

38、 nor tested for such applications, damage and premature failure are possible. These resistors only see a onetime pulse (Short-time overload) as part of the group B inspection. 6.6 User of record. Coordination of this document for future revisions is coordinated only with the approved sources of supp

39、ly and the users of record of this document. Requests to be added as a recorded user of this drawing may be achieved on-line at resistordla.mil or in writing to: DLA Land and Maritime, ATTN: VAT, P.O. Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-8754 or DSN 850-8754. Provided by IHSNo

40、t for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 88020 REV C PAGE 8 6.7 Sources of supply. Approved sources of supply are listed herein. Additional sources will be added as they become

41、available. Assistance in the use of this drawing may be obtained on on-line at resistordla.mil or contact DLA Land and Maritime, ATTN: VAT, P.O. Box 3990, Columbus, OH 43218-3990, or by telephone (614) 692-8754 or DSN 850-8754. DLA Land and Maritime drawing PIN Vendor similar designation or type num

42、ber 1/ Vendor CAGE Vendor name and address 88020- 001 002 003 004 005 006 007 008 L018 L020 L005 L006 L007 L008 L009 L015 57027 IRC, Inc. Advance Film Division 4222 S. Staples Street Corpus Christi, TX 78411-2702 1/ Parts must be purchased to the DLA Land and Maritime PIN to assure that all performance requirements and test are met. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-