DLA DESC-DWG-89085 REV D-2009 CAPACITORS FIXED ELECTROLYTIC POLARIZED ALUMINUM OXIDE SNAP MOUNT LOW PROFILE.pdf

1、 REVISIONS LT DESCRIPTION DATE APPROVED A Modified table I, deleted references to MIL-STD-1285, changed capacitance tolerance. Deleted dash numbers 154 through 192 and substituted 193 through 232. 16 Jul 90 D. Moore B Editorial changes throughout. 31 July 2000 Kendall A. Cottongim C Editorial change

2、s throughout. 19 April 2006 Michael A. Radecki D Editorial changes throughout. 6 Oct 2009 Michael A. Radecki WARNING! To avoid injury to personnel or damage to equipment or property, caution must be exercised in testing or use of capacitors covered by this drawing. (see 6.1). CURRENT DESIGN ACTIVITY

3、 CAGE CODE 037Z3 DEFENSE LOGISTICS AGENCY DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 Prepared in accordance with ASME Y14.100 Source control drawing REV PAGE REV PAGE REV STATUS OF PAGES REV D D D D D D D D D D D D PAGES 1 2 3 4 5 6 7 8 9 10 11 12 PMIC N/A PREPARED BY Robert E. Grillot

4、 DESIGN ACTIVITY DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444-5000 Original date of drawing 30 AUGUST 1989 CHECKED BY David E. Moore TITLE CAPACITORS, FIXED, ELECTROLYTIC POLARIZED, ALUMINUM OXIDE, SNAP MOUNT, LOW PROFILE APPROVED BY David E. Moore SIZE A CODE IDENT. NO. 14933 DWG NO. 89085 RE

5、V D PAGE 1 OF 12 AMSC N/A 5910-E431 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DESIGN ACTIVITY DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444-5000 SIZE A CODE IDENT NO. 14933 DWG NO. 89085 REV D PAGE 2 1. SCOPE 1.1 Scope. This drawing descri

6、bes the requirements for aluminum oxide, electrolytic capacitors. 1.2 Part or Identifying Number (PIN). The complete PIN shall be as follows: 89085 XXX Drawing Dash number number (see table I) 2. APPLICABLE DOCUMENTS 2.1 GeneralThe documents listed in this section are specified in sections 3 and 4 o

7、f this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specifi

8、ed requirements of documents in sections 3 and 4 of this specification, whether of not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless

9、 otherwise specified, the issues of these documents are those cited in the solicitation or contract (see 6.3). DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-39018 - Capacitors, Fixed, Electrolytic (Aluminum Oxide), Established Reliability, and Non-established Reliability, General Specification for. S

10、TANDARDS DEPARTMENT OF DEFENSE STANDARDS MIL-STD-202 - Test Methods Standard for Electronic and Electrical Component Parts. MIL-STD-1285 - Marking of Electrical and Electronic Parts. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or from the Standardization

11、 Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applic

12、able laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Interface and physical dimensions. The interface and physical dimensions shall be as specified herein (see figure 1). 3.1.1 Terminals. Terminals shall be snap-mount (see figure 1). 3.1.2 Case. Case shall be

13、made with insulated tubular metal. 3.1.3 Operating and storage temperature range. The operating and storage temperature range shall be -40C to +105C. 3.1.4 Insulating sleeves. Insulating sleeves shall meet the requirements of MIL-PRF-39018. Provided by IHSNot for ResaleNo reproduction or networking

14、permitted without license from IHS-,-,-DESIGN ACTIVITY DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444-5000 SIZE A CODE IDENT NO. 14933 DWG NO. 89085 REV D PAGE 3 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Thermoplastic insulation sleeve t

15、o be permanently fixed to aluminum case. FIGURE 1. Case dimensions and configuration. Inches mm .004 .039 .040 .079 .25 .394 0.10 0.99 1.02 2.01 6.35 10.01 Case code Inches mm Diameter Length Diameter Length HA HB HD JA JB JC JD JE KA KB KC KD KE MB MC MD ME .87 .87 .87 1.00 1.00 1.00 1.00 1.00 1.18

16、 1.18 1.18 1.18 1.18 1.38 1.38 1.38 1.38 1.00 1.18 1.57 1.00 1.18 1.38 1.57 2.00 1.00 1.18 1.38 1.57 2.00 1.18 1.38 1.57 2.00 22.1 22.1 22.1 25.4 25.4 25.4 25.4 25.4 30.0 30.0 30.0 30.0 30.0 35.1 35.1 35.1 35.1 25.4 30.0 39.9 25.4 30.0 35.1 39.9 50.8 25.4 30.0 35.1 39.9 50.8 30.0 35.1 39.9 50.8 Prov

17、ided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DESIGN ACTIVITY DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444-5000 SIZE A CODE IDENT NO. 14933 DWG NO. 89085 REV D PAGE 4 3.2 Electrical characteristics. 3.2.1 Rated voltage. The rated voltage shall be

18、 in accordance with table I. 3.2.2 Dielectric. The dielectric shall be aluminum oxide in accordance with MIL-PFR-39018. 3.2.3 Capacitance. Nominal capacitance shall be within +20 percent of the value shown in table I at +25C, measured at 120 Hz and 1.0 V rms maximum. 3.2.4 Equivalent series resistan

19、ce (ESR). Equivalent series resistance at 120 Hz and 10-40 kHz shall not exceed the values shown in table I at +25C, when measured with a maximum of 1.0 V rms applied. 3.2.5 DC leakage current. DC leakage current shall not exceed values determined from the equation: Where I = leakage current in micr

20、oamperes k = a constant: 4.0 at +25C 32.0 at +105C C = rated capacitance in microfarads V = rated dc voltage In no case, however, shall the dc leakage current exceed 20,000 A when normally stabilized at +105C. 3.2.6 Ripple current. Capacitors shall withstand the rms ripple current of 120 Hz and 10-4

21、0 kHz at +105C (see table I). 3.2.7 Life test. One hundred percent of rated voltage shall be applied at +105C for 2,000 hours. a. Capacitors shall then be removed from the test chamber and stabilized at room temperature. b. The capacitance, when measured in accordance with 3.2.3, shall not have chan

22、ged more than 15 percent from the initial value. c. The equivalent series resistance, when measured in accordance with 3.2.4, shall not have increased to more than 150 percent of the initial requirement. d. The leakage current shall meet the requirement specified in 3.2.5. 3.2.8 Reverse voltage. Not

23、 applicable. 3.2.9 Reverse voltage agingCVkI =. Not applicable. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DESIGN ACTIVITY DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444-5000 SIZE A CODE IDENT NO. 14933 DWG NO. 89085 REV D PAGE 5 3.3 Environ

24、mental characteristics. 3.3.1 Altitude operation. The altitude operation shall not exceed 200,000 feet. 3.3.2 Shelf test. Capacitors shall be subjected to a shelf test at +105C 3C for 500 hours. No voltage shall be applied. After test, capacitors shall be removed from the test chamber and stabilized

25、 at room temperature. a. The capacitance, when measured in accordance with 3.2.3, shall be within 15 percent of the initial measured value. b. The equivalent series resistance, when measured as specified in accordance with 3.2.4, shall not exceed 130 percent of the initial requirement. c. The leakag

26、e current, when measured as specified in 3.2.5, except, 10 minutes after reaching rated working voltage, shall not exceed 200 percent of the initial requirement. 3.4 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be u

27、sed to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.5 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be a sug

28、gested source of supply. 3.6 Marking. Marking shall be in accordance with MIL-STD-1285, except the (part name) shall be marked with the PIN as specified herein (see 1.2), the manufacturers name or Commercial and Government Entity (CAGE) code, and date lot codes. 3.7 Workmanship. The capacitor shall

29、be uniform in quality and free from any defects that will affect life, serviceability, or appearance. 4. VERIFICATION 4.1 Qualification inspection. Qualification inspection is not required. 4.2 Conformance inspection. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall

30、 consist of the group A solderability and terminal strength test of group B of MIL-PRF-39018. 4.2.2 Certification. The acquiring activity, at its discretion, may accept a certificate of compliance with group B inspections in lieu of performing group B tests (see 6.3c). 4.2.3 Inspection of packaging.

31、 Inspection of packaging shall be in accordance with MIL-PRF-39018. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DESIGN ACTIVITY DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444-5000 SIZE A CODE IDENT NO. 14933 DWG NO. 89085 REV D PAGE 6 5. PACK

32、AGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.3). When actual packaging of materiel is to be performed by DoD personnel, these personnel need to contact the responsible packaging activity to ascertain requisite packagi

33、ng requirements. Packaging requirements are maintained by the Inventory Control Points packaging activity within the Military Department or Defense Agency, or within the Military Departments System Command. Packaging data retrieval is available from the managing Military Departments or Defense Agenc

34、ys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general or explanatory nature, which may be helpful, but is not mandatory.) 6.1 Warning. The watt-second ratings of the capacitors listed in this drawi

35、ng are relatively high and if they are improperly tested or used an EXPLOSION could occur or a SHOCK HAZARD could result. If the capacitors are to be used IN LARGE BANKS it is important that suitable precaution be observed in the testing and use of these capacitors. For example, adequate bleeder res

36、istors should be provided and the mechanical structure of capacitor banks should be such as to withstand any large fault currents, which may occur in the event of a short circuit. Capacitor bank design should be such as to eliminate, so far as reasonably possible, any exposure to a shock hazard. 6.2

37、 Intended use. Capacitors conforming to this drawing are intended for use when military specifications do not exist and qualified military devices that will perform the required function are not available for OEM application. This drawing is intended exclusively to prevent the proliferation of unnec

38、essary duplicate specifications, drawings, and stock catalog listings. When a military specification exists and the product covered by this drawing has been qualified for listing, this drawing becomes obsolete and will not be used for new design. 6.3 Ordering data. The contract or purchase order sho

39、uld specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery of one copy of the conformance inspection data or certificate of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Requirements for packaging and packing. 6.4

40、 Replaceability. Capacitors covered by this drawing will replace the same commercial device covered by contractor-prepared specification or drawing. 6.5 Users of record. Coordination of this document for future revisions is coordinated only with the suggested sources of supply and the users of recor

41、d of this document. Requests to be added as a recorded user of this drawing should be in writing to: Defense Supply Center, Columbus (DSCC), ATTN: DSCC-VAT, Post Office Box 3990, Columbus, OH 43218-3990, by e-mail to capacitorfilterdla.mil or by telephone (614) 692-0561 or DSN 850-0561. 6.6 Approved

42、 source of supply. Approved source of supply is listed herein. Additional sources will be added as they become available. For assistance in the use of this drawing, contact Defense Supply Center, Columbus, ATTN: DSCC-VAT, P. O. Box 3990, Columbus, OH 43218-3990, capacitorfilterdla.mil , or by teleph

43、one (614) 692-0561 or DSN 850-0561. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DESIGN ACTIVITY DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444-5000 SIZE A CODE IDENT NO. 14933 DWG NO. 89085 REV D PAGE 7 TABLE I. Electrical characteristics. DS

44、CC drawing 89085- F 20 percent Maximum ESR at +25C (M) Maximum rms ripple at +85C amperes Maximum rms ripple at +105C amperes Case code Vendor CAGE number Similar 1/ vendor type 100/120 Hz 20-40 kHz 100/120 Hz 20-40 kHz 100/120 Hz 20-40 kHz 6.3 V dc working, 8 V dc surge 01 02 03 04 05 06 07 08 09 1

45、0 11 12 13 14 15 16 17 6,800 10,000 10,000 12,000 15,000 15,000 18,000 22,000 22,000 27,000 27,000 27,000 33,000 39,000 47,000 47,000 56,000 119 109 91 84 102 95 79 73 60 56 94 90 65 60 53 49 73 69 42 39 60 57 40 37 49 46 33 31 39 37 27 25 21 20 2.4 2.5 2.9 3.0 2.8 2.9 3.4 3.5 4.0 4.1 3.3 3.3 3.9 4.

46、1 4.7 4.9 3.9 4.1 5.6 5.8 4.6 4.7 5.9 6.2 5.3 5.5 6.9 7.1 6.5 6.7 8.0 8.3 9.8 10.0 1.2 1.2 1.4 1.4 1.4 1.4 1.7 1.7 2.0 2.0 1.6 1.6 1.9 2.0 2.3 2.4 1.9 2.0 2.8 2.8 2.3 2.3 2.9 3.1 2.6 2.7 3.4 3.5 3.2 3.3 4.0 4.1 4.9 5.0 HA HB JA JB HD KA JC JD KB JE KC MB KD MC KE MD ME 7M138 7M138 7M138 7M138 7M138

47、7M138 7M138 7M138 7M138 7M138 7M138 7M138 7M138 7M138 7M138 7M138 7M138 81D682P6R3HA2 81D103P6R3HB2 81D103P6R3JA2 81D123P6R3JB2 81D153P6R3HD2 81D153P6R3KA2 81D183P6R3JC2 81D223P6R3JD2 81D223P6R3KB2 81D273P6R3JE2 81D273P6R3KC2 81D273P6R3MB2 81D333P6R3KD2 81D393P6R3MC2 81D473P6R3KE2 81D473P6R3MD2 81D563P6R3ME2 10 V dc working, 12 V dc surge 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 5,600 6,800 8,200 10,000 12,000 12,000 12,000 15,000 15,000 18,000 22,000 22,000 27,000 27,000 33,000 33,000 47,000 121 109 93 84 111 95