DLA DESC-DWG-89089 REV C-2013 CAPACITORS FIXED CERAMIC CHIP HIGH VOLTAGE.pdf

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Editorial changes throughout. 31 July 2000 Kendall A. Cottongim B Editorial changes throughout. 10 April 2006 Michael A. Radecki C Editorial changes throughout. 21 May 2013 Michael A. Radecki Prepared in accordance with ASME Y14.100 REV STATUS REV C C C C C

2、 C C OF PAGES PAGES 1 2 3 4 5 6 7 PMIC N/A PREPARED BY ROBERT E. GRILLOT DESIGN ACTIVITY DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444-5000 Original date of drawing 17 JULY 1989 CHECKED BY EDWARD H. BACK TITLE CAPACITORS, FIXED, CERAMIC, CHIP, HIGH VOLTAGE APPROVED BY DAVID E. MOORE SIZE A CODE

3、 IDENT. NO. 14933 DWG NO. 89089 REV C PAGE 1 OF 7 AMSC N/A 5910-2013-E11 CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER, DAYTON,

4、 OHIO 45444-5000 SIZE A CODE IDENT NO. 14933 DWG NO. 89089 REV C PAGE 2 1. SCOPE 1.1 Scope. This drawing and MIL-PRF-55681 describe the requirements for high voltage, ceramic, chip capacitors. 1.2 Part or Identifying Number (PIN) The complete PIN is as follows: 89089 -XXX Drawing number Dash number

5、(see table I) 2. APPLICABLE DOCUMENTS 2.1 General The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every

6、effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents in sections 3 and 4 of this specification, whether of not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks.

7、The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract (see 6.2). DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-55681 - Capacitor, Chi

8、p, Multiple Layer, Fixed, Un-encapsulated, Ceramic Dielectric, Established Reliability, and Non-established Reliability, General Specification For. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-202 - Test Methods for Electronic and Electrical Component Parts. MIL-STD-1285 - Marking of Electrical and Elect

9、ronic Parts. (Copies of these documents are available online at http:/quicksearch.dla.mil/ from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.3 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflic

10、t between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Interface and physical dimensions. The int

11、erface and physical dimensions shall be as specified in MIL-PRF-55681 and herein (see figure 1). 3.1.1 Termination. Chip capacitors shall be provided with palladium silver termination, 50 micro-inches minimum nickel barrier, coated with SN60 or SN62 (see figure 1) and shall be solderable when tested

12、 in accordance with MIL-STD-202, method 208. 3.1.2 Pure tin. The use of pure tin, as an underplate or final finish is prohibited both internally and externally. Tin content of capacitor components and solder shall not exceed 97 percent, by mass. Tin shall be alloyed with a minimum of 3 percent lead,

13、 by mass (see 6.3). 3.1.3 Operating temperature range. The operating temperature range shall be -55C to +125C. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER, DAYTON, OHIO 45444-5000 SIZE A CODE IDENT NO. 14933 DWG N

14、O. 89089 REV C PAGE 3 3.2 Electrical characteristics. 3.2.1 Rated voltage. See table I. 3.2.2 Dielectric type. Ceramic. 3.2.3 Temperature coefficient. +90 30 ppm/C (-55 to +125C). 3.2.4 Operating frequency. Up to 50 GHz. NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general

15、 information only. 3. The solder coated device may exceed the above body dimensions by a maximum of.006 inches. FIGURE 1. Case dimensions and configuration. Inches mm .006 0.15 .010 0.25 .015 0.38 .170 4.32 .390 9.91 .395 10.03 Dimensions L Max W Max T Max Y .395 .390 .170 .015 .010 Provided by IHSN

16、ot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER, DAYTON, OHIO 45444-5000 SIZE A CODE IDENT NO. 14933 DWG NO. 89089 REV C PAGE 4 3.2.5 Measurement frequency. 1 MHz for values up through 1000 pF; 1 KHz for values above 1000 pF. 3.2.6 C

17、apacitance. See table I. Measured in accordance with method 305 of MIL-STD-202, 1 MHz at 10 V rms at +25C. 3.2.7 Dissipation factor (+25C). 0.1 percent maximum measured under the same conditions as capacitance. 3.2.8 Insulation resistance. Measured in accordance with method 302 of MIL-STD-202, at ra

18、ted voltage. At +25C: 100,000 megohms minimum. At +125C: 10,000 megohms minimum. 3.2.9 Dielectric withstanding voltage. Two times working voltage (WVDC). 3.2 10 Capacitance tolerance: C = 0.25 pF D = 0.5 pF J = 5 percent K = 10 percent M = 20 percent 3.3 Solderability of terminals. In accordance wit

19、h MIL-PRF-55681 (see 3.1.1). 3.4 Immersion cycling. In accordance with MIL-PRF-55681. 3.5 Moisture resistance. In accordance with MIL-PRF-55681 with 20 continuous cycles. 3.6 Life. 150 percent of rated voltage for 2,000 hours at +125C in accordance with MIL-STD-202, method 108, test condition F. 3.7

20、 Thermal shock. MIL-STD-202, method 107, test condition B, except low temperature is -55C. 3.8 Voltage conditioning. In accordance with MIL-PRF-55681, 100 percent of rated voltage. 3.9 KVA rating. The KVA rating is determined from the maximum voltage or maximum current (see table I). 3.10 Marking. M

21、arking shall be on the package only due to the small size of the chips and be in accordance with MIL-STD-1285, except the PIN shall be as specified in 1.2 with manufacturers name or CAGE code and date code. 3.11 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or en

22、vironmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.12 Manufacturer eligibility. To be eligible for listing as an approved

23、 source of supply, a manufacturer shall be listed in the MIL-PRF-55681 Qualified Products Database for at least one part, or perform the group A and group C inspections of MIL-PRF-55681 on a sample of parts agreed upon by the manufacturer and DLA Land and Maritime-VAT. 3.13 Certificate of compliance

24、. A certificate of compliance shall be required from manufacturers requesting to be an approved source of supply. 3.14 Workmanship. The capacitors shall be uniform in quality and free from any defects that will affect life, serviceability, or appearance. 4. VERIFICATION 4.1 Qualification inspection.

25、 Qualification inspection is not required. 4.2 Conformance inspection. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of all tests specified in group A inspection of MIL-PRF-55681 provided they are listed in this drawing. PPM testing and calculation is not

26、 applicable. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER, DAYTON, OHIO 45444-5000 SIZE A CODE IDENT NO. 14933 DWG NO. 89089 REV C PAGE 5 TABLE I. Electrical characteristics. DSCC drawing 89089- Capacitance pF Tole

27、rance WVDC Maximum RF volt RMS at +25C Power storage (KVA) Vendor CAGE number Similar vendor type 1/ 001 1.0 C 3600 2500 12 29990 ATC100E1R0CP3600X 002 1.0 D 3600 2500 12 29990 ATC100E1R0DP3600X 003 1.2 C 3600 2500 12 29990 ATC100E1R2CP3600X 004 1.2 D 3600 2500 12 29990 ATC100E1R2DP3600X 005 1.5 C 3

28、600 2500 12 29990 ATC100E1R5CP3600X 006 1.5 D 3600 2500 12 29990 ATC100E1R5DP3600X 007 1.8 C 3600 2500 12 29990 ATC100E1R8CP3600X 008 1.8 D 3600 2500 12 29990 ATC100E1R8DP3600X 009 2.2 C 3600 2500 12 29990 ATC100E2R2CP3600X 010 2.2 D 3600 2500 12 29990 ATC100E2R2DP3600X 011 2.7 C 3600 2500 12 29990

29、ATC100E2R7CP3600X 012 2.7 D 3600 2500 12 29990 ATC100E2R7DP3600X 013 3.3 C 3600 2500 12 29990 ATC100E3R3CP3600X 014 3.3 D 3600 2500 12 29990 ATC100E3R3DP3600X 015 3.9 C 3600 2500 12 29990 ATC100E3R9CP3600X 016 3.9 D 3600 2500 12 29990 ATC100E3R9DP3600X 017 4.7 C 3600 2500 12 29990 ATC100E4R7CP3600X

30、018 4.7 D 3600 2500 12 29990 ATC100E4R6DP3600X 019 5.6 C 3600 2500 12 29990 ATC100E5R6CP3600X 020 5.6 D 3600 2500 12 29990 ATC100E5R6DP3600X 021 6.8 C 3600 2500 12 29990 ATC100E6R8CP3600X 022 6.8 D 3600 2500 12 29990 ATC100E6R8DP3600X 023 8.2 C 3600 2500 12 29990 ATC100E8R2CP3600X 024 8.2 D 3600 250

31、0 12 29990 ATC100E8R2DP3600X 025 10.0 J 3600 2500 12 29990 ATC100E100JP3600X 026 10.0 K 3600 2500 12 29990 ATC100E100KP3600X 027 10.0 M 3600 2500 12 29990 ATC100E100MP3600X 028 12.0 J 3600 2500 12 29990 ATC100E120JP3600X 029 12.0 K 3600 2500 12 29990 ATC100E120KP3600X 030 12.0 M 3600 2500 12 29990 A

32、TC100E120MP3600X 031 15.0 J 3600 2500 12 29990 ATC100E150JP3600X 032 15.0 K 3600 2500 12 29990 ATC100E150KP3600X 033 15.0 M 3600 2500 12 29990 ATC100E150MP3600X 034 18.0 J 3600 2500 12 29990 ATC100E180JP3600X 035 18.0 K 3600 2500 12 29990 ATC100E180KP3600X 036 18.0 M 3600 2500 12 29990 ATC100E180MP3

33、600X 037 22.0 J 3600 2500 12 29990 ATC100E220JP3600X 038 22.0 K 3600 2500 12 29990 ATC100E220KP3600X 039 22.0 M 3600 2500 12 29990 ATC100E220MP3600X 040 27.0 J 3600 2500 12 29990 ATC100E270JP3600X 041 27.0 K 3600 2500 12 29990 ATC100E270KP3600X 042 27.0 M 3600 2500 12 29990 ATC100E270MP3600X 043 33.

34、0 J 3600 2500 12 29990 ATC100E330JP3600X 044 33.0 K 3600 2500 12 29990 ATC100E330KP3600X 045 33.0 M 3600 2500 12 29990 ATC100E330MP3600X 046 39.0 J 3600 2500 12 29990 ATC100E390JP3600X 047 39.0 K 3600 2500 12 29990 ATC100E390KP3600X 048 39.0 M 3600 2500 12 29990 ATC100E390MP3600X 049 47.0 J 3600 250

35、0 12 29990 ATC100E470JP3600X 050 47.0 K 3600 2500 12 29990 ATC100E470KP3600X 051 47.0 M 3600 2500 12 29990 ATC100E470MP3600X 052 56.0 J 3600 2500 12 29990 ATC100E560JP3600X 053 56.0 K 3600 2500 12 29990 ATC100E560KP3600X 054 56.0 M 3600 2500 12 29990 ATC100E560MP3600X 055 68.0 J 3600 2500 12 29990 A

36、TC100E680JP3600X 056 68.0 K 3600 2500 12 29990 ATC100E680KP3600X 057 68.0 M 3600 2500 12 29990 ATC100E680MP3600X See footnote at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER, DAYTON, OHIO 45444-5000 S

37、IZE A CODE IDENT NO. 14933 DWG NO. 89089 REV C PAGE 6 TABLE I. Electrical characteristics. DSCC drawing 89089- Capacitance pF Tolerance WVDC Maximum RF volt RMS at +25C Power storage (KVA) Vendor CAGE number Similar vendor type 1/ 058 75.0 J 3600 2500 12 29990 ATC100E750JP3600X 059 75.0 K 3600 2500

38、12 29990 ATC100E750KP3600X 060 75.0 M 3600 2500 12 29990 ATC100E750MP3600X 061 82.0 J 3600 2500 12 29990 ATC100E820JP3600X 062 82.0 K 3600 2500 12 29990 ATC100E820KP3600X 063 82.0 M 3600 2500 12 29990 ATC100E820MP3600X 064 100.0 J 3600 2500 12 29990 ATC100E101JP3600X 065 100.0 K 3600 2500 12 29990 A

39、TC100E101KP3600X 066 100.0 M 3600 2500 12 29990 ATC100E101MP3600X 067 120.0 J 3600 2500 12 29990 ATC100E121JP3600X 068 120.0 K 3600 2500 12 29990 ATC100E121KP3600X 069 120.0 M 3600 2500 12 29990 ATC100E121MP3600X 070 150.0 J 3600 2500 12 29990 ATC100E151JP3600X 071 150.0 K 3600 2500 12 29990 ATC100E

40、151KP3600X 072 150.0 M 3600 2500 12 29990 ATC100E151MP3600X 073 180.0 J 3600 2500 12 29990 ATC100E181JP3600X 074 180.0 K 3600 2500 12 29990 ATC100E181KP3600X 075 180.0 M 3600 2500 12 29990 ATC100E181MP3600X 076 220.0 J 3600 2500 12 29990 ATC100E221JP3600X 077 220.0 K 3600 2500 12 29990 ATC100E221KP3

41、600X 078 220.0 M 3600 2500 12 29990 ATC100E221MP3600X 079 270.0 J 3600 2500 12 29990 ATC100E271JP3600X 080 270.0 K 3600 2500 12 29990 ATC100E271KP3600X 081 270.0 M 3600 2500 12 29990 ATC100E271MP3600X 082 330.0 J 3600 2500 12 29990 ATC100E331JP3600X 083 330.0 K 3600 2500 12 29990 ATC100E331KP3600X 0

42、84 330.0 M 3600 2500 12 29990 ATC100E331MP3600X 085 390.0 J 3600 2500 12 29990 ATC100E391JP3600X 086 390.0 K 3600 2500 12 29990 ATC100E391KP3600X 087 390.0 M 3600 2500 12 29990 ATC100E391MP3600X 088 470.0 J 2500 1800 6 29990 ATC100E471JP2500X 089 470.0 K 2500 1800 6 29990 ATC100E471KP2500X 090 470.0

43、 M 2500 1800 6 29990 ATC100E471JP2500X 091 560.0 J 2500 1800 6 29990 ATC100E561JP2500X 092 560.0 K 2500 1800 6 29990 ATC100E561KP2500X 093 560.0 M 2500 1800 6 29990 ATC100E561MP2500X 094 680.0 J 2500 1800 6 29990 ATC100E681JP2500X 095 680.0 K 2500 1800 6 29990 ATC100E681KP2500X 096 680.0 M 2500 1800

44、 6 29990 ATC100E681MP2500X 097 820.0 J 1000 700 6 29990 ATC100E821JP1000X 098 820.0 K 1000 700 6 29990 ATC100E821KP1000X 099 820.0 M 1000 700 6 29990 ATC100E821MP1000X 100 1000.0 J 1000 700 6 29990 ATC100E102JP1000X 101 1000.0 K 1000 700 6 29990 ATC100E102KP1000X 102 1000.0 M 1000 700 6 29990 ATC100

45、E102MP1000X 103 1200.0 J 1000 700 6 29990 ATC100E122JP1000X 104 1200.0 K 1000 700 6 29990 ATC100E122KP1000X 105 1200.0 M 1000 700 6 29990 ATC100E122MP1000X 106 1500.0 J 1000 700 6 29990 ATC100E152JP1000X 107 1500.0 K 1000 700 6 29990 ATC100E152KP1000X 108 1500.0 M 1000 700 6 29990 ATC100E152MP1000X

46、109 1800.0 J 1000 700 6 29990 ATC100E182JP1000X 110 1800.0 K 1000 700 6 29990 ATC100E182KP1000X 111 1800.0 M 1000 700 6 29990 ATC100E182MP1000X 112 2200.0 J 1000 700 6 29990 ATC100E222JP1000X 113 2200.0 K 1000 700 6 29990 ATC100E222KP1000X 114 2200.0 M 1000 700 6 29990 ATC100E222MP1000X 1/ Parts mus

47、t be purchased to the DSCC PIN to assure that all performance requirements are met. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER, DAYTON, OHIO 45444-5000 SIZE A CODE IDENT NO. 14933 DWG NO. 89089 REV C PAGE 7 5. PA

48、CKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD personnel or in-house contractor personnel, these personnel need to contact the responsible packaging activity to

49、 ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activity within the Military Department or Defense Agency, or within the Military services system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-RO