DLA DESC-DWG-91019 REV J-2012 CAPACITORS FIXED CERAMIC CHIP 56 礔 THROUGH 1 礔.pdf

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Added suggested source of supply. Added 1 F at 25 V dc, .065 T maximum. Editorial changes throughout. 16 May 94 D. Moore B Page 4 Revised inspection of product for delivery requirements. 23 May 96 Andrew R. Ernst C Page 2 - Added termination finish options.

2、 Page 3 - Added footnote for dimensional tolerance change for solder coated parts. Page 4 - Added Voltage Temperature Limit requirements. Changed insulation resistance requirements. Revised marking and workmanship paragraphs. Added environmental and mechanical requirements paragraph. Table I; Change

3、d -05 T max dimension. Page 5 - Incorporated inspection of product for delivery requirements into drawing from MIL-PRF-55681. Page 6 - Added note regarding tin plated finish. Page 7 - Revised sources of supply list. Editorial changes throughout. 2 June 99 Kenneth A. Bernier D Added suggested source

4、of supply that was added by letter dated January 15, 1999. 11 August 99 Kendall A. Cottongim E Added suggested source of supply. 16 November 00 Kendall A. Cottongim F Added suggested source of supply. 5 February 02 Kendall A. Cottongim G Page 7 - Corrected vendor E part numbers 7 August 02 Kendall A

5、. Cottongim H 5 year review. Editorial changes throughout. 22 January 08 Michael A. Radecki J Added eligibility requirement. Updated vendor C. Removed termination finish “Y”. 3 July 2012 Michael A. Radecki Prepared in accordance with ASME Y14.100 Source control drawing REV STATUS OF PAGES REV J J J

6、J J J J PAGES 1 2 3 4 5 6 7 PMIC N/A PREPARED BY ROBERT GRILLOT DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OH Original date of drawing 91-09-11 CHECKED BY EDWARD H. BACK TITLE CAPACITORS, FIXED, CERAMIC, CHIP, .56 F THROUGH 1 F APPROVED BY DAVID E. MOORE SIZE A CODE IDENT. NO. 14933 DWG NO. 91019 REV

7、J PAGE 1 OF 7 AMSC N/A 5910-2012-E09CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 HAS CHANGED NAMES TO: DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CO

8、DE IDENT NO. 14933 DWG NO. 91019 REV J PAGE 2 1. SCOPE 1.1 Scope. This drawing and MIL-PRF-55681 describe the complete requirements for ceramic chip capacitors. 1.2 Part or Identifying Number (PIN). The complete PIN shall be as follows: 91019 -XX - Drawing Dash number Termination finish Number (see

9、table I) (if required (see 3.1.1) 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as e

10、xamples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents cited in sections 3 and 4 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications,

11、 standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-123 -

12、 Capacitors, Fixed, Ceramic Dielectric, (Temperature Stable and General Purpose), High Reliability, General Specification for. MIL-PRF-55681 - Capacitor, Chip, Multiple Layer, Fixed, Ceramic Dielectric, Established Reliability and Non-Established Reliability, General Specification for. DEPARTMENT OF

13、 DEFENSE STANDARDS MIL-STD-202 - Test Methods Standard Electronics and Electrical Component Parts. MIL-STD-1285 - Marking of Electrical and Electronic Parts. (Copies of these documents are available online at https:/assist.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Rob

14、bins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.3 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, howev

15、er, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Interface and physical dimensions. The interface and physical dimensions shall be as specified in MIL-PRF-55681 and herein (see figure 1). 3.1.1 Termination finish. The termination finis

16、h shall be solder coated over a base metallization and barrier metal (as specified in MIL-PRF-55681, “U” termination finish). When requested by the acquiring activity, an optional termination finish shall be identified by a single letter following the dash number as follows: Z: Base metallization -

17、barrier metal - tinned (tin/lead alloy, with a minimum of 4 percent lead): as specified in MIL-PRF-55681. Note: Termination finish Y (tin, 100 percent) has been removed from this specification (see 3.1.1.1). Termination finishes U and Z are substitutable for termination finish Y. Provided by IHSNot

18、for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 91019 REV J PAGE 3 Dimensions (See note 3) L +.025 -.010 W +.010 -.020 Y Min .225 .210 .010 Notes: 1. Dimensions are in inches. 2. Metric

19、equivalents are given for general information only. 3. For solder coated parts an additional +.025 to the length and width tolerance is allowed. An additional +.020 tolerance is allowed on the thickness (see table I). FIGURE 1. Case dimensions and configuration. Inches mm .010 0.25 .020 0.51 .025 0.

20、64 .210 5.33 .225 5.72 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 91019 REV J PAGE 4 3.1.1.1 Pure tin. The use of pure tin, as an underplate or final finish is pr

21、ohibited both internally and externally. Tin content of resistor components and solder shall not exceed 97 percent, by mass. Tin shall be alloyed with a minimum of 3 percent lead, by mass (see 6.2). 3.1.2 Operating temperature range. The operating temperature range shall be -55C to +125C. 3.2 Electr

22、ical characteristics. 3.2.1 Rated voltage. The rated voltage shall be in accordance with table I. 3.2.2 Dielectric type. The dielectric type shall be ceramic. 3.2.3 Temperature coefficient and voltage temperature limits (VTL). The temperature coefficient shall be 0 15 percent (-55C to +125C) and sha

23、ll meet the VTL requirements of characteristic BR of MIL-PRF-55681. 3.2.4 Operating frequency. Operating frequency shall be up to 50 GHz. 3.2.5 Capacitance. See table I. Measured in accordance with method 305 of MIL-STD-202, 1 kHz at 1.0 V rms 0.2 V rms at +25C. 3.2.6 Dissipation factor (+25C). 2.5

24、percent maximum (measured under the same conditions as capacitance). 3.2.7 Insulation resistance. Measured in accordance with method 302 of MIL-STD-202 at rated voltage. At +25C: 100,000 megohms or 1,000 megohm-microfarads, whichever is less. At +125C: 10,000 megohms or 100 megohm-microfarads, which

25、ever is less. 3.2.8 Dielectric withstanding voltage. 2.0 times rated voltage. 3.2.9 Capacitance tolerance. K = 10 percent. 3.3 Environmental and mechanical requirements. The environmental and mechanical requirements shall be in accordance with MIL-PRF-55681. 3.4 Marking. Capacitors may be marked wit

26、h the PIN as specified in 1.2, but are not required to be marked. Marking shall be on the package and shall be in accordance with MIL-STD-1285, except the PIN shall be as specified in 1.2, with the manufacturers name or CAGE code and date code. 3.5 Manufacturer eligibility. To be eligible for listin

27、g as an approved source of supply, a manufacturer shall be listed in the MIL-PRF-55681 or MIL-PRF-123 Qualified Products Database (QPD) for at least one part, or perform the group A and group B inspections specified herein on a sample of parts agreed upon by the manufacturer and DLA Land and Maritim

28、e-VAT. 3.6 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be an approved source of supply. TABLE I. Electrical characteristics DSCC drawing PIN 91019- 1/ Capacitance F Capacitance tolerance WV dc T Max 01- 02- 03- 04- 05- .56 .68 .82 1.0 1.0

29、 K K K K K 50 50 50 50 25 .065 .065 .090 .090 .070 1/ Complete PIN shall include an additional symbol to indicate termination finish where applicable (see 1.2). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON,

30、 OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 91019 REV J PAGE 5 3.7 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and ma

31、intenance requirements, and promotes economically advantageous life cycle costs. 3.8 Workmanship. Capacitors shall be so processed that when inspected under 20X to 40X magnification, they shall be uniform in quality and shall be free from pits, cracks, rough edges, adhered foreign material, and othe

32、r defects which will affect life or serviceability. The capacitors shall exhibit no delamination (separation in the layers of ceramic) or demetallization (lift-off) on the terminations. 4. VERIFICATION 4.1 Qualification inspection. Qualification inspection is not required. 4.2 Conformance inspection

33、. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of groups A and B inspections of this drawing (see tables II and III). 4.2.2 Certification. The acquiring activity, at its discretion, may accept a certificate of compliance for group B requirements in lieu

34、of performing group B tests (see 6.3f). TABLE II. Group A Inspection. Inspection Requirement paragraph of MIL-PRF-55681 Test method paragraph of MIL-PRF-55681 Sampling Procedure Subgroup 1 Voltage conditioning 3.6 4.8.3 100 percent inspection Subgroup 2 IR (at +125C) Visual and mechanical examinatio

35、n 3.9 3.1, 3.4, 3.5, 3.5.1, 3.24 through 3.26 inclusive 4.8.6 4.8.2 Table X, column A of MIL-PRF-55681 Table X, column B of MIL-PRF-55681 Subgroup 3 Solderability 3.13 4.8.10 13 samples/0 failures allowed Subgroup 4 Voltage-temperature limits 3.14 (and 3.2.3 herein) 4.8.11 13 samples/ 0 failures all

36、owed TABLE III. Group B inspection. Inspection Requirement paragraph of MIL-PRF-55681 Test method paragraph of MIL-PRF-55681 Number of Sample units to be inspected Number of defectives permitted Subgroup 1 Thermal shock and immersion 3.15 4.8.12 12 0 Subgroup 2 Resistance to soldering heat Moisture

37、resistance 3.16 3.17 4.8.13 4.8.14 12 0 Subgroup 3 Life (at +125C) 3.19 4.8.16 25 0 Subgroup 4 Humidity, steady state, low voltage 3.18 4.8.15 12 0 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A

38、CODE IDENT NO. 14933 DWG NO. 91019 REV J PAGE 6 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.3). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to co

39、ntact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activities within the Military Service or Defense Agency, or within the military services system commands. Packaging data retrieval is availab

40、le from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general or explanatory nature which may be helpful, but is not mandatory.) 6.1 Intended use.

41、Capacitors conforming to this drawing are intended for use when military specifications do not exist and qualified military devices that will perform the required function are not available for original equipment manufacturer application. This drawing is intended exclusively to prevent the prolifera

42、tion of unnecessary duplicate specifications, drawings, and stock catalog listings. When a military specification exists and the product covered by this drawing has been qualified for listing, this drawing becomes obsolete and will not be used for new design. 6.2 Tin whisker growth. The use of alloy

43、s with tin content greater than 97 percent, by mass, may exhibit tin whisker growth problems after manufacture. Tin whiskers may occur anytime from a day to years after manufacture and can develop under typical operating conditions, on products that use such materials. Conformal coatings applied ove

44、r top of a whisker-prone surface will not prevent the formation of tin whiskers. Alloys of 3 percent lead, by mass, have shown to inhibit the growth of tin whiskers. For additional information on this matter, refer to ASTM-B545 (Standard Specification for Electrodeposited Coatings of Tin). 6.3 Order

45、ing data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery of one copy of the conformance inspection data or certificate of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c.

46、 Requirements for packaging and packing. d. Title, number, and date of the specification. e. Whether the manufacturer performs the group B tests or provides certification of compliance for group B requirements. f. Requirements for notification of change of product to acquiring activity, if applicabl

47、e. 6.4 Replaceability. Capacitors covered by this drawing will replace the same commercial device covered by contractor prepared specification or drawing. 6.5 Changes from previous issue. The margins of this specification are marked with vertical lines to indicate where changes from the previous iss

48、ue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and rel

49、ationship to the previous issue. 6.6 Users of record. Coordination of this document for future revisions is coordinated only with the approved source(s) of supply and the users of record of this document. Requests to be added as a recorded user of this drawing may be achieved online at capacitorfilterdla.mil or if in writing to: DLA Land and Maritime, ATTN: VAT, Post Office Box 3990, C