DLA DSCC-DWG-03028 REV E-2011 CAPACITORS FIXED CERAMIC CHIP 0603.pdf

1、 REVISIONS LT DESCRIPTION DATE APPROVED A Added “J” tolerance (5%) to all BR and BX capacitors. Added paragraph 6.4. Revised tables VI, VII, and VIII. 21 April 2008 Michael A. Radecki B Added vendor D. 12 March 2010 Michael A. Radecki C Changed address of vendor C 1 July 2010 Michael A. Radecki D Up

2、dated tables VII and VIII for vendor C. 9 November 2010 Michael A. Radecki E Added K and M tolerance to BP capacitors. Specified the life test sample size. Updated tables VI, VII, and VIII. 13 October 2011 Michael A. Radecki Prepared in accordance with ASME Y14.100 Source control drawing REV STATUS

3、REV E E E E E E E E E E OF PAGES PAGES 1 2 3 4 5 6 7 8 9 10 PMIC N/A PREPARED BY MICHAEL A. RADECKI DESIGN ACTIVITY DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH Original date of drawing 1 October 2004 CHECKED BY PATRICK G. KYNE TITLE CAPACITORS, FIXED, CERAMIC, CHIP, 0603 APPROVED BY KENDALL A. COTT

4、ONGIM SIZE A CODE IDENT. NO. 037Z3 DWG NO. 03028 REV E PAGE 1 OF 10 AMSC N/A 5910-2011-E16CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 HAS CHANGED NAMES TO: DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DE

5、FENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 03028 REV E PAGE 2 1. SCOPE 1.1 Scope. This drawing and MIL-PRF-55681 describe the requirements for ceramic, chip. 1.2 Part or Identifying Number (PIN) The complete PIN is as follows: 03028- BX 102 B J Z - Drawing numbe

6、r Dielectric (see 1.2.1) Capacitance value (see 1.2.2) Voltage (see 1.2.3) Capacitance tolerance (see 1.2.4) Termination finish (see 1.2.5) Group C testing option (see 1.2.6) 1.2.1 Dielectric. The dielectric type is identified by the following 2 letters as defined in 3.3.1: BP, BR, BX. 1.2.2 Capacit

7、ance value. The nominal capacitance value, expressed in picofarads (pF) is identified by a three digit number; the first two digits represent significant figures and the last digit specifies the number of zeros to follow. When the nominal value is less than 10 pF, the letter “R” is used to indicate

8、the decimal point and the succeeding digit(s) of the group represent significant figure(s). 1R0 indicates 1.0 pF; R75 indicates .75 pF; and 0R5 indicates 0.5 pF. See tables VI, VII, and VIII for values. 1.2.3 Voltage. The rated voltage for continuous operation at +125C is identified by a single lett

9、er as shown in table I. TABLE I. Rated voltage. Symbol Rated voltage (volts, dc) W 6.3 X 10 Y 16 Z 25 A 50 B 100 C 200 1.2.4 Capacitance tolerance. The capacitance tolerance is identified by a single letter in accordance with table II. TABLE II. Capacitance tolerance. Symbol Capacitance tolerance ()

10、 Tolerance applicability C .25 pF BP 10 pF D .50 pF BP 10 pF F 1 percent BP 10 pF G 2 percent BP 10 pF J 5 percent BP 10 pF, BX, BR K 10 percent BP 10 pF, BX, BR M 20 percent BP 10 pF, BX, BR Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SU

11、PPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 03028 REV E PAGE 3 1.2.5 Termination finish. Termination finish is identified by a single letter as shown in table III. TABLE III. Termination finish. Symbol Termination finish M Palladium-silver U Base metallization-barrier me

12、tal-solder coated (tin/lead alloy, with a minimum of 4 percent lead). Solder has a melting point of +200C or less. Solder coat thickness is a minimum of 60 microinches. Z Base metallization-barrier metal-tinned (tin/lead alloy, with a minimum of 4 percent lead) 1.2.6 Group C testing option. To requi

13、re MIL-PRF-55681 group C testing, use the appropriate letter from table IV. If group C testing is not desired, leave this location blank. NOTE: Ordering group C options that contain a 2,000 hour life test may extend the processing time by 90 days or more. TABLE IV. Group C testing option. Letter Gro

14、up C testing option C Full group C L 2,000 hour life test only M 1,000 hour life test only H Low voltage humidity only N/A No group C testing. 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not incl

15、ude documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents in sections 3 and 4

16、 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these docume

17、nts are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-55681 - Capacitor, Chip, Multiple Layer, Fixed, Unencapsulated, Ceramic Dielectric, Established Reliability and Non-Established Reliability, General Specification For. DEPARTMENT OF DEFENSE STANDARDS MI

18、L-STD-202 - Electronic and Electrical Component Parts, Test Methods for. MIL-STD-1285 - Marking of Electrical and Electronic Parts. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building

19、 4D, Philadelphia, PA 19111-5094.) 2.3 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applic

20、able laws and regulations unless a specific exemption has been obtained. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 03028 REV E PAGE 4 T W Y L NOTES: 1. Dimension

21、s are in inches. 2. Metric equivalents are given for general information only. 3. Dimensions and tolerances are for bare chips. For solder coated terminations (symbol U), add .020 inch (0.51 mm) to the positive length tolerance and .015 inch (0.38 mm) to the positive width and thickness tolerances.

22、FIGURE 1. Case dimensions and configuration. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-55681, and as specified herein. Unless otherwise stated, these capacitors shall be capable of meeting all electrical, environmental, and mechanical

23、 requirements of MIL-PRF-55681. 3.2 Interface and physical dimensions. The interface and physical dimensions shall be as specified in MIL-PRF-55681 and herein (see figure 1). 3.2.1 Tin plated finishes. Tin plating is prohibited as a final finish or as an undercoat. Tin-lead (Sn-Pb) finishes are acce

24、ptable provided that the minimum lead content is 4 percent (see 6.4). 3.3 Electrical characteristics. Inches mm .006 0.15 .014 0.36 .032 0.81 .036 0.91 .063 1.60 Dimensions L .006 W .006 T Max Y .006 .063 .032 .036 .014 Provided by IHSNot for ResaleNo reproduction or networking permitted without lic

25、ense from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 03028 REV E PAGE 5 3.3.1 Dielectric type. The dielectric type shall be BP (30 ppm/C), BR (+15, -40 percent) or BX (+15, -25 percent) ceramic in accordance with MIL-PRF-55681. TABLE V. Voltage-tempera

26、ture limits. Symbol Capacitance change with reference to +25C Step A through step D of MIL-PRF-55681 table XIII Percent rated voltage Step E through step G of MIL-PRF-55681 table XIII BP 0 30 ppm/C 100 0 30 ppm/C BR 15 percent 100 +15, -40 percent BX 15 percent 100 +15, -25 percent 3.3.2 Capacitance

27、. Capacitance shall be in accordance with tables VI, VII, and VIII when measured in accordance with method 305 of MIL-STD-202. The following conditions shall apply: a. Test frequency: 1 MHz 50kHz (for all BP characteristic capacitors 1,000 pF); or 1kHz 50Hz for all other capacitors. b. Test voltage:

28、 1.0 volt 0.2 volt rms. 3.3.3 Dissipation factor (+25C). The dissipation factor shall not exceed 0.15 percent for BP characteristic capacitors, 5.0 percent for 6.3V to 10V BR and BX characteristic capacitors, 3.5 percent for 16V to 25V BR and BX characteristic capacitors, and 2.5 percent for 50V to

29、200V BR and BX characteristic capacitors. 3.3.4 Insulation resistance. At +25C: minimum of 100,000 megohms or 1,000 megohm-microfarads, whichever is less. At +125C: minimum of 10,000 megohms or 100 megohm-microfarads, whichever is less for BR and BX dielectrics; and minimum of 1,000 megohms or 10 me

30、gohm-microfarads, whichever is less for BP dielectric. 3.4 Solderability. In accordance with MIL-PRF-55681, except the sample size shall be 5 pieces with zero defectives permitted. 3.5 Moisture resistance. In accordance with MIL-PRF-55681, with the following exceptions: a. Polarizing voltage shall b

31、e rated voltage. b. Testing may be performed on chips with a larger width and/or length as long as they are cut from the same wafer(s) as those used for production. 3.6 Marking. As a minimum, marking shall be on the package due to the small size of the chips. The package marking shall be in accordan

32、ce with MIL-STD-1285, except the PIN shall be as specified in paragraph 1.2 with manufacturers name or CAGE code and date code. The manufacturer may, at their option, mark some information on the chips. 3.7 Manufacturer eligibility. To be eligible for listing as an approved source of supply, a manuf

33、acturer shall be listed in the MIL-PRF-55681 Qualified Products Database for at least one part, or perform the group A and group C inspections specified herein on a sample of parts agreed upon by the manufacturer and DLA Land and Maritime-VAT. 3.8 Certificate of compliance. A certificate of complian

34、ce shall be required from manufacturers requesting to be an approved source of supply. 3.9 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exce

35、eds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.10 Workmanship. In accordance with MIL-PRF-55681. 4. VERIFICATION 4.1 Qualification inspection. Qualification inspection is not required. Provided by IHSNot for ResaleNo reproduction or netwo

36、rking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 03028 REV E PAGE 6 4.2 Conformance inspection. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of all tests specified in group A

37、of MIL-PRF-55681. ESR testing and PPM testing and calculation are not applicable. When optional group C testing is requested, terminal strength and series resonance are not applicable. In addition, the life test sample shall be 25 with one defective permitted. 5. PACKAGING 5.1 Packaging. For acquisi

38、tion purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging

39、 requirements are maintained by the Inventory Control Points packaging activities within the Military Service or Defense Agency, or within the military services system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files,

40、 CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general or explanatory nature that may be helpful, but is not mandatory.) 6.1 Intended use. Capacitors conforming to this drawing are intended for use when military specifications

41、do not exist and qualified military devices that will perform the required function are not available for OEM application. This drawing is intended exclusively to prevent the proliferation of unnecessary duplicate specifications, drawings, and stock catalog listings. When a military specification ex

42、ists and the product covered by this drawing has been qualified for listing, this drawing becomes obsolete and will not be used for new design. 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery of one copy of the c

43、onformance inspection data or certificate of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Requirements for notification of change of product to acquiring activity, if applicable. d. Requirements for packaging and packing. 6.3 Replaceabi

44、lity. Capacitors covered by this drawing will replace the same commercial device covered by a contractor-prepared specification or drawing. 6.4 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker growth problems after manufacture. Tin whis

45、kers may occur anytime from a day to years after manufacture and can develop under typical operating conditions, on products that use such materials. Conformal coatings applied over top of a whisker-prone surface will not prevent the formation of tin whiskers. Alloys of 3 percent lead, by mass, have

46、 shown to inhibit the growth of tin whiskers. For additional information on this matter, refer to ASTM-B545 (Standard Specification for Electrodeposited Coatings of Tin). 6.5 Users of record. Coordination of this document for future revisions is coordinated only with the approved sources of supply a

47、nd the users of record of this document. Requests to be added as a recorded user of this drawing should be in writing to: DLA Land and Maritime, ATTN: VAT, Post Office Box 3990, Columbus, OH 43218-3990, by e-mail to capacitorfilterdla.mil, or by telephone (614) 692-4709 or DSN 850-4709. 6.6 Approved

48、 sources of supply. Approved sources of supply are listed herein. Additional sources will be added as they become available. For assistance in the use of this drawing, contact DLA Land and Maritime, ATTN: VAT, Post Office Box 3990, Columbus, OH 43218-3990, by e-mail to capacitorfilterdla.mil, or by

49、telephone (614) 692-4709 or DSN 850-4709. 6.7 Changes from previous issue. The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to eval