DLA DSCC-DWG-04013-2004 CONNECTOR RECEPTACLE ELECTRICAL SERIES BMZ SOCKET CONTACT FOR SEMIRIGID CABLE《半刚性电缆用BMZ系列插座接触电机贮器连接器》.pdf

1、REVISIONS LTR DESCRIPTION DATE APPROVED Requirements of DSCC drawing 84148 are applicable. Prepared in accordance with ASME Y14.100 REV PAGE REV REV STATUS OF PAGES PAGE 1 2 3 4 5 PREPARED BY PMIC G Ron Gary DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43216-5000 CHECKED BY Lee Surowiec APPROVED B

2、Y Richard Taylor TITLE CONNECTOR, RECEPTACLE, ELECTRICAL, SERIES BMZ, SOCKET CONTACT, FOR SEMIRIGID CABLE SIZE CAGE CODE 037Z3 DWG. NO. 04013 Original date of drawing 30 June 2004 A REV PAGE 1 OF 5 AMSC N/A 5935-E740 Provided by IHSNot for ResaleNo reproduction or networking permitted without licens

3、e from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 04013 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV PAGE 2 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Wrench flats are to accommodate standard wrench opening in accordance with FED-S

4、TD-H28, appendix 10. 4. All undimensioned pictorial configurations are for reference purposes only. 5. Dimension .576 (14.63 mm) defines the maximum overall length of the connector when assembled to the cable. 6. Method of assembly to the cable shall be solder. 7. Unless otherwise specified, toleran

5、ces are .005 (0.13 mm). 8. Series BMZ interface in accordance with MIL-STD-348, socket contact. FIGURE 1. General configuration. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 04013 DEFENSE SUPPLY CENTER, COLUMBUS COLUMB

6、US, OH 43216-5000 A REV PAGE 3 ENGINEERING DATA: Nominal impedance: 50 ohms. Frequency range: 2 - 18 GHz. (Connector performance only, frequency range is dependent on cable used.) Voltage rating: 335 V rms at sea level. 85 V rms at 70,000 feet. Temperature rating: -65C to +165C. REQUIREMENTS: Requir

7、ements of drawing 84148 is applicable. Dimensions and configuration: See figure 1 and MIL-STD-348. Force to engage and disengage: Longitudinal force: Not applicable. Torque: Not applicable. Mating characteristics: Center contact: Oversize test pin: .0215 +.0001/-.0000. Test pin finish: 16 micrinches

8、. Insertion depth: .070. Number of insertions: 1. Insertion force test: Steel test pin diameter: .0210 +.0000/-.0001. Insertion depth: .070. Test pin finish: 16 microinches. Insertion force: 12 ounces, max. Withdrawal force test: Steel test pin diameter: .0195 +.0001/-.0000. Insertion depth: .070. W

9、ithdrawal force: 2 ounces, min. Test pin finish: 16 microinches. Coupling proof torque: Not applicable. Hermetic seal: Not applicable. Leakage (pressurized connectors): Not applicable. Insulation resistance: Method 302, test condition B, MIL-STD-202; 10,000 megohms minimum. Center contact retention:

10、 4 pounds minimum, axial force Radial torque: Not applicable. Voltage standing wave ratio (VSWR): 1.07 + .010 F (GHz), maximum. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 04013 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBU

11、S, OH 43216-5000 A REV PAGE 4 Moisture resistance: Method 106, MIL-STD-202, no measurements at high humidity. Insulation resistance shall be at least 200 megohms within 5 minutes after removal from humidity. Contact resistance (in milliohms, maximum): Initial After environment Center contact: 4.0 4.

12、0 Outer contact: 2.0 Not applicable Outer conductor to body: 0.5 Not applicable Dielectric withstanding voltage at sea level: 1000 V rms, minimum. 250 V rms at 70,000 feet. Vibration, high frequency: Method 204, test condition D, MIL-STD-202. Corona level: Altitude: 70,000 feet. 250 V rms, minimum.

13、Shock (specified pulse): Method 213, test condition I, MIL-STD-202. Thermal shock: Method 107, test condition B, MIL-STD-202, except test high temperature shall be +85C. Barometric pressure (reduced): Not applicable. RF high potential withstanding voltage: 670 V rms, minimum. Frequency: 5 MHz. Leaka

14、ge current: Not applicable. Cable retention force: 30 pounds, minimum. Torque: 16 ounce-inches, minimum. Coupling mechanism retention force: Not applicable. RF leakage: -85 F (F in GHz) dB, minimum. Test at a frequency between 2 and 3 GHz. RF insertion loss: .04 F, GHz dB, maximum. Note: These parts

15、 are for use in general radio frequency applications. Part or Identifying Number (PIN): See table I. TABLE I. Connector to cable reference. PIN Cable accommodation 04013ZSPA M17/133-RG405 M17/133-0001 through -00005 Provided by IHSNot for ResaleNo reproduction or networking permitted without license

16、 from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 04013 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV PAGE 5 Approved sources of supply are listed herein. Additional sources will be added as they become available. The vendors listed on the requirements drawing have agreed to this drawing an

17、d a certificate of compliance has been submitted to DSCC-VAI. DSCC drawing PIN 1/ Vendor CAGE number Vendor reference PIN 04013ZSPA 95077 SF8934-6008 1/ Parts must be purchased to this DSCC PIN to assure that all performance requirements and tests are met. Vendor CAGE Vendor Name and Number address 95077 S/V Microwave, Inc. 2400 Centrepark West Dr. WPB, Fl 33409 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-