DLA DSCC-DWG-04028-2004 CONNECTOR HIGH DENSITY BLADE AND FORK BACKPANEL EIGHT ROW 452 CONTACT POSITIONS《452接触 立场八排 后面板刀片和叉子板高密度连接器》.pdf

1、REVISIONS LTR DESCRIPTION DATE APPROVED Prepared in accordance with ASME Y14.100 REV PAGE 16 17 REV REV STATUS OF PAGES PAGE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 PREPARED BY PMIC N/A William Carpenter DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43216-5000 CHECKED BY TITLE Lee Surowiec APPROVED BY

2、Richard L. Taylor CONNECTOR, HIGH DENSITY, BLADE AND FORK, BACKPANEL, EIGHT ROW, 452 CONTACT POSITIONS SIZE CAGE CODE 037Z3 DWG. NO.04028 Original date of drawing 27 September 2004 A REV A PAGE 1 OF 17 AMSC N/A 5935-E752 Provided by IHSNot for ResaleNo reproduction or networking permitted without li

3、cense from IHS-,-,-SIZE CAGE CODE DWG NO. 1. SCOPE 1.1 Scope. This drawing outlines the requirements for a specific member of a family of compact, high contact density (.050 inch (1.27 mm), high performance two-piece electrical connectors. These connectors are intended for printed circuit board (plu

4、g in dual heat sink daughter board modules, and fixed backplane) applications utilizing surface mount daughter board and compliant pin backpanel termination techniques. The connector family includes members that provide combinations of low power signal contacts, power contacts, shielded contacts and

5、 optical termini. These connectors may be used in severe operating environments, and may include protective hoods, contact sealing, interfacial seals, electrostatic shielding and other features. This connector family is organized and fabricated utilizing modular design, with connector module blocks

6、which can be grouped to provide for combinations of low power signal contacts, fiber optic termini, power contacts, and shielded contacts. Specific implementation groupings of these module blocks constitute elements of the connector family. This drawing details a backpanel member of the connector fa

7、mily, composed of groups of 10 insulator block contact assemblies for low power fork type contacts, providing a total of 452 signal contacts. This assembly mates with a companion daughter card connector per DSCC drawing 04027. The backpanel connector assembly also includes an electrostatic shield wh

8、ich mates with a daughter card connector metal shroud, providing an electrostatic shield for all contacts in the connector pair. The backpanel connector insulator blocks also provide for installation of three connector keyed bushings, and allows for use of a center guide pin. This family member does

9、 not include module blocks containing fiber optic, power, or shielded contact elements. These members of this connector family are included DSCC drawings 93003 through 93013. 1.2 Part or Identifying Number (PIN). The complete PIN shall be as specified on the item requirements drawing and constructed

10、 using the following format: 04028 A A 45200 E S NDSCC Insulator Termination Contact Termination Keying Contact requirement material style number tail length pin sealing drawing (see 1.2.1) (see 1.2.2) (see 1.2.3) (see 1.2.4) (see 1.2.5) (see 1.2.6) 1.2.1 Insulator material. Insulator material shall

11、 be fabricated using one of the following plastic materials: A - Thermoplastic, type GPT-30F in accordance with MIL-M-24519, or ASTM-D-5138. 1.2.2 Termination style. Connectors shall be terminated using the following termination techniques: A - Compliant pin termination. 1.2.3 Contact number. The PI

12、N shall include 5 digits to identify the total number of contacts. The first three digits will identify the number of signal contacts, with the following two digits identifying the number of special contacts (shielded, fiber optic, power). An example follows: 452 00 Number of signal contacts (3 digi

13、ts required) Number of special contacts (2 digits required) (NOT AVAILABLE) 037Z3 04028 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REVPAGE2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 1.2.4 Termination tail l

14、ength. The PIN will include a single character (A thru F) taken from table I, which will identify the termination tail length, allowing for use in various thickness backplanes, and also possible additional wire wrapping of the termination tails. TABLE I. Termination tail length. 1/ 2/ 3/ Term type T

15、ermination tail length X 4/ Inches (mm) A .160 (4.06) B .220 (5.59)C .310 (7.87) D .350 (8.89)E .400 (10.16) F .490 (12.45)1/ Dimensions are in inches. 2/ Metric equivalents are in parentheses. 3/ Metric equivalents are given for information only. 4/ X is a reference dimension only. See figure 2. 1.

16、2.5 Keying pins. The PIN will contain a single character for this feature. S - To be ordered separately, see DSCC drawing 04023. 1.2.6 Sealing. The PIN will contain a single character (N or S) to indicate if the connector termination area is sealed from the contact blades which extend above the conn

17、ector insulator blocks. (CONTACT SEALING NOT AVAILABLE) 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this drawing. This section does not include documents cited in other sections of this drawing or recommended for additional informati

18、on or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all requirements of documents cited in sections 3 and 4 of this drawing. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The followi

19、ng specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-M-24519 - Molding Plastic, Electrical, Thermopla

20、stic. (Copies of this document are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 037Z3 04028 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-50

21、00 A REVPAGE3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 2.2.2 Other Government documents, drawings, and publications. The following other Government documents, drawings, and publications form a part of this document to th

22、e extent specified herein. Unless otherwise specified, the issues are those cited in the solicitation or contract. 89065 - General Specification for High Performance, High Density, Two Piece, Printed Circuit Board Connectors (Copies of this document are available online at http:/www.dscc.dla.mil/ or

23、 Defense Supply Center, Columbus, ATTN: DSCC-VAI, P.O. Box 3990 Columbus, Ohio 43216-5200.) 2.3 Non-Government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitat

24、ion or contract. ASTM INTERNATIONAL ASTM A582 - Free-Machining Stainless and Heat-Resisting Steel Bars ASTM B194 - Copper-Beryllium Alloy Plate, Sheet, Strip, and Rolled Bar ASTM B488 - Gold for Engineering Uses, Electrodeposited Coatings of ASTM B768 - Copper-Cobalt-Beryllium Alloy Strip and Sheet

25、(Copies of these documents are available online from http:/www.astm.org or ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, Pennsylvania, USA 19428-2959.) NATIONAL CONFERENCE OF STANDARDS LABORATORIES (NCSL) NCSL Z540.1 - Laboratories Calibration and Measuring and Test Equi

26、pment (Copies of this document are available online from http:/www.ncsli.org/ or National Conference of Standards Laboratories (NCSL), 2995 Wilderness Place Suite 107, Boulder, CO 80301-5404). SOCIETY OF AUTOMOTIVE ENGINEERS (SAE) SAE-AMS-2404 - Nickel Electroless Plating SAE-AMS-QQ-P-35 - Passivati

27、on Treatments for Corrosion-Resistant Steel SAE-AMS-QQ-N-290 - Nickel Plating (Electrodeposited) (Copies of these documents are available online from http:/www.sae.org or SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001). 2.4 Order of precedence. In the event of a conflict betwee

28、n the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 037Z3 04028 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A

29、REVPAGE4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 3. REQUIREMENTS 3.1 DSCC requirements. Items shall meet the requirements of DSCC drawing 89065 for blade and fork type connectors except as specified herein. Any requirem

30、ents included in this drawing shall be in addition to, or supersede those requirements included in DSCC drawing 89065. In case of conflict between the requirements in this drawing and those in DSCC drawing 89065, the requirements of this drawing shall take precedence. 3.2 Design configuration. The d

31、esign, construction, and physical dimensions shall be as specified in this drawing and DSCC drawing 89065. 3.2.1 Design documentation. Design documentation shall be in accordance with DSCC drawing 89065, shall be retained by the manufacturer, and shall be available upon request for review by the con

32、tracting activity, DSCC, or contractor. 3.3 Electrical and environmental performance characteristics. The electrical and environmental characteristics shall be in accordance with DSCC drawing 89065 unless otherwise specified in this drawing. 3.4 Marking. The connector shall be marked with the DSCC d

33、rawing PIN, the manufacturers name or CAGE code, and the production date code in accordance with DSCC drawing 89065. The marking shall be permanent and legible. PIN marking position and details shall be as indicated in 1.2. 3.5 Material requirements. The materials to be used in construction and fabr

34、ication shall be as specified in this drawing. Materials required, but not specified in this drawing, shall be in accordance with DSCC drawing 89065. 3.5.1 Connector materials. 3.5.1.1 Connector insulator. The connector insulator blocks shall be thermoplastic, glass reinforced, in accordance with MI

35、L-M-24519, type GPT-30F. 3.5.1.2 Tuning fork contact and termination tails. Tuning fork contacts and termination tails shall be beryllium copper in accordance with ASTM-B194 C17200, or ASTM-B768. 3.5.1.2.1 Tuning fork contact and termination tail finish. The tuning fork contacts and termination tail

36、s shall be plated with a minimum of 50 microinches of gold over all areas in accordance with ASTM-B488, type 3, code C, class 1.27, over 50 to 150 microinches of nickel in accordance with SAE-AMS-QQ-N-290, class 2. 3.5.1.3 EMI shield. The EMI shield shall be constructed from beryllium copper in acco

37、rdance with ASTM-B194 or ASTM-B768. 3.5.1.3.1 EMI shield finish. The EMI shield finish shall be nickel in accordance with SAE-AMS-2404. 3.5.1.4 Polarizing key material. The key pin shall be stainless steel in accordance with ASTM A582, 300 series, low magnetic permeability. 3.5.1.4.1 Polarizing key

38、finish. The polarizing key finish shall be passivated in accordance with SAE-AMS QQ-P-35. 3.6 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible, provided that the material meets or

39、exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 037Z3 04028 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REVPAGE5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CO

40、DE DWG NO. 4. VERIFICATION 4.1 Classification of inspections. The inspection requirements specified herein are classified as follows: a. Qualification inspection (see 4.2). b. Conformance inspection (see 4.3). 4.1.1 Equipment calibration. All test equipment and inspection facilities shall be maintai

41、ned in accordance with NCSL Z540.1. 4.2 Qualification inspection. Qualification inspection for connectors specified herein shall not be required. 4.3 Quality conformance. Shall be in accordance with DSCC drawing 89065. 4.4 Certification as an approved source of supply. In order to be listed as an ap

42、proved source of supply, a manufacturer shall: a. Agree to make available to DSCC, upon request, all pertinent test data on the subject part indicating compliance to the tests outlined in DSCC drawing 89065. 037Z3 04028 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REVPAGE6 b. Provide to

43、 DSCC-VAI, or its designated agent, upon request, free of change and without obligation, current production samples of the types and quantities requested. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. NOTES: 1. Dimensions are

44、 in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified, the tolerance for 2 place decimals is .01 inch (0.3 mm); the tolerance for 3 place decimals is .005 inch (0.13 mm); angular tolerance is 030. FIGURE 1. Connector face view. 037Z3 04028 DEFENSE SUPPLY CEN

45、TER, COLUMBUS COLUMBUS, OH 43216-5000 A REVPAGE7 Inches mm .050 .075 .250 2.800 3.075 5.850 6.150 6.37 1.27 1.90 6.35 71.12 78.10 148.59 156.21 161.80 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE (See table I for dimension X) (Shown

46、 installed in PWB, rotated 90 CW) NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified, the tolerance for 2 place decimals is .01 inch (0.3 mm); the tolerance for 3 place decimals is .005 inch (0.13 mm); angular tolerance is 030. FIG

47、URE 2. Connector cross sectional view. 037Z3 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REVProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHSDWG NO. 04028 PAGE8 Inches mm .016 .100 .125 .150 .200 .240 .257 .350 .465 .50 0.41 2.54 3.17 3.81 5.

48、08 6.10 6.53 8.89 11.81 12.70 -,-,-SIZE CAGE CODE DWG NO.NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified, the tolerance for 2 place decimals is .01 inch (0.3 mm); the tolerance for 3 place decimals is .005 inch (0.13 mm); angula

49、r tolerance is 030. FIGURE 3. Printed wiring board layout. 037Z3 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REVInches mm .002 0.05 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-.025 .050 0.64 1.27 04028 PAGE9 .118 .144 .150 .200 .275 .350 2.800 3.050 3